How to start a Harley Davidson that wont start?

Insert 1 wire into the female terminal that would be #30 in the fuse panel socket. Insert the other WIRE (NOT END of 1st wire) into #87 of the fuse panel socket. 6) Make SURE bike is in NEUTRAL. 7) Turn on ignition ON and Kill switch to run. When you touch both of your installed wires together DOES bike crank./start? Click to expand…

Why is my Harley Davidson Road King not starting?

If you have a Tachometer, disconnect it. A bad tach can interrupt proper coil function. i have problem error code U1301 in Harley Davidson Road King 2009 and test everything not starts . I have a 92 FXRSP, I recently replaced my switches and I had a new battery.

Can you start a Harley Davidson HD without a fob?

Starting your HD without a Fob! Your HD has the ability to be started without a Fob present jus in case the Fob is lost or the battery goes dead! Your Pin# to over-ride the security system is usually loaded up with the last 5 numbers of your Harley’s serial # backwards! (EX: serial # last 5 is 1 2 3 4 5……….it was entered as 5 4 3 2 1).

What’s the voltage on a Harley Davidson starter?

I check the voltage at the kill switch and get 12.3 from the black and white wire that goes to the kill switch and the start button. But, I only get 9.2 volts from the black and red wire from the start switch to the start relay. All the fuses are good and there are 12 volts to the starter and the solenoid.

What should I do if my Harley Davidson won’t start?

Here’s where to start your search when your bike won’t start and you have no idea why. This article applies to the Harley Davidson Touring models (2009-present). So the weekend has finally arrived. Boots on, gloves, jacket and helmet: check. You even checked your tires: 36 front and 38 rear.

Are there any problems with the Street Glide?

One problem that I have with the Street Glide (though this is by no means the only bike with which I’ve had this issue) is wind buffeting.

What do you need to start a Harley Davidson?

The bike has to have a signal from the key fob before it will allow the bike to start. The TSSM is the – turn signal security module ( Japan & Korean markets only) I asked the dealer is they could test the ECM and they said yes if it on the bike.

Is it good to buy a starter motorcycle?

No need to be discouraged, though. Choosing your starter motorcycle wisely can help you enjoy a smoother learning experience, so you can eventually move on to premium bikes (or an entire collection!)

What to do if your bike won’t start?

Your battery may have enough charge to run the electronics, the fuel pump even, but not enough to turn over the motor. With a digital multimeter, test the battery’s voltage. If is isn’t reading over 12V, you’re under charged and it’s a good place to start. Plug in your battery charger, and come back in an hour to try again.

Where is the start relay on a Harley Davidson?

It is the GRAY one. On the inside cover there is a label that will identify the START Relay. 4) Look at the bottom of the removed gray relay closely. You will see pin notation as follows. 87,,87A,,30,,85,,86. 5) Leave the relay REMOVED from the bike.

Why does my Dyna FXDC bike not start?

Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing. Not even a click or a buzz. Bike has been sitting for about 2 weeks.

What does the Check Engine light on a Harley Davidson mean?

The check engine light is designed for a reason; it is there to tell you that there is something wrong with your Harley Davidson Dyna Glide. The dealership will charge you over $100 to read and clear the code for you.

What to do if your Harley Davidson is not starting?

If you only have spark on the front cylinder, swap plug wires (front to rear, rear to front ). Now see if you (only) have spark on the rear cylinder. If you do not have power to the coil; Use a small jumper wire and power your coil directly from the battery. This will will bypass your harness and switches.

How to reset check engine on Harley Davidson Dyna Glide?

Press and hold the trip reset button located on the side of your speedometer. Turn the ignition key to on. Hold the button until the word “diag” appear on the odometer screen, which stands for diagnose. Figure 2. Hold trip button. Figure 3.

What to do when your motorbike wont start?

Look up direct start button cover. It can get you out of a jam when the solenoid acts up. Won’t help if the battery is to low to crank the engine though. Was this answer helpful? I dont own a motorbike.

What to do when your car won’t start?

In that case you need a new starter motor or you could try to rebuild your solenoid. The starter motor and is very easy to swap out. First, disconnect your battery. Do not skip this step. Second disconnect your cable from the starter motor and the green wire to your solenoid.

Why does my motorcycle not start with the side stand down?

Newer bikes (and some older ones) may refuse to start with the side stand down. Along with all the other high-tech sensors that are on board, your motorcycle might have a built-in code that keeps the ignition from starting if your kickstand is engaged.

What to do when your Harley Davidson won’t start?

Try neutral with clutch pulled in. Also battery connections , solenoid wire. The security system lights only flash after I turn off the bike. I have the bike in neutral and I even tried pulling in the clutch a couple of times. I checked the wire to the solenoid and it had power.

When did I replace the battery on my Street Glide?

I have a 2014 Street Glide Special with about 40k miles. I replace the main battery in February and then last week I took the bike for a ride. After stopping for a drink, the bike would not start.

Why does my bike not start when I Turn on the ignition?

If okay, check that the switch is getting power from the ignition switch when the ignition switch is turned on. If not, your ignition switch may be faulty at the lead that supplies power to the starter switch and is probably the culprit because we know the ignition circuit works – it’s the starter circuit in question.

What should I do if my motorcycle won’t start?

If the reading stays steady, your battery is good to go—and your motorcycle likely has another problem (or a few problems). Fortunately, there are other troubleshooting means that can help determine why your bike won’t start.

Why does my Harley Davidson crank but not start?

There have been a few reports of a P1009 code – incorrect password also. It appears the turn signal and stalls or cranks but will not start. Try removing the ecm and security fuses, wait ten minutes and reinstall the fuses. This “reboots” the turn signal module and the motorcycle will then start from that point on.

What does it mean when your bike won’t start?

This is usually an indication that the fuel or bike ignition is the culprit. With time, the gas will start breaking down which will make it hard for it to combust. If this happens, you will find that the bike will crank but will not be able to start.

What causes a motorcycle engine to not start?

1. Ignition switch turned off. 2. A faulty ignition switch. 3. Engine run switch in off position. 4. A defective engine run switch. 5. Loose or corroded starter and battery cables (solenoid chatters). 6. A discharged or defective battery. 7. A defective starter motor. 8. A defective starter solenoid. 9. A defective starter shaft pinion gear. 10.

What should I do if my motorcycle battery wont start?

If you don’t see these symptoms or are otherwise unsure what to look for, the first step is ensuring that the battery is operational and providing the maximum voltage. To confirm your battery is still good, you should visually inspect it, check the voltage, and load test the battery. A visual battery inspection should involve:

Why does my Harley Davidson start and stall?

All in all it’s a strong running bike and this is usually just a minor annoyance, still if there’s a quick fix I’d love to hear it.Thanks -Bob A: Bob, the most common reason a m/c will act this way is because of an intake leak. Start the bike cold. Mist the intake flanges with brake cleaner.

What does Softail mean on a Harley Davidson?

Harley Davidson Softail will not crank refers to when the crankshaft will not turn so as to start the engine. In other words, not only will the Softail engin… Harley Davidson Softail will not crank refers to when the crankshaft will not turn so as to start the engine.

How to fix a Harley Davidson Softail Sportster?

Style and Performance Upgrades Milwaukee Eight Touring Softail & Dyna Sportster Everyday Hog How-To Fix My Hog Projects M8 Cam Upgrade Cam Chain Tensioner Shoe Cam Gear Drive Conversion Carburetor Rebuild Electrical Systems Handlebars 101

What to do when your Harley starts stalling?

Start the bike cold. Mist the intake flanges with brake cleaner. If your bike’s idle drops, or the engine stalls, you have an intake leak. If this is the case, replace the intake seals along with the front & rear intake flanges. If the bike passes the intake test; have the dealer or your mechanic scan the m/c for possible codes.

What causes a Harley Davidson engine to stall?

A: Bob, the most common reason a m/c will act this way is because of an intake leak. Start the bike cold. Mist the intake flanges with brake cleaner. If your bike’s idle drops, or the engine stalls, you have an intake leak.

Where can I buy a 2006 Harley Davidson?

Find 2006 Harley-Davidson listings for sale near you. #1 insurer: 1 out of 3 insured riders choose Progressive. Savings: We offer plenty of discounts, and rates start at just $75/year. OEM parts in repairs: We use OEM parts in repairs and don’t depreciate anything.

What happens if you dont have a key fob for a Harley Davidson?

You start your beloved Harley and ride off into the sunset. You stop at your favorite watering hole completely unaware you do not have your key fob. You pick up a hot chick and she jumps on the back of your Harley. Ooooops, you look like a fool and you can’t start or turn on your Harley. Don’t worry, you can save yourself.

Is the Harley Davidson V-Rod a muscle car?

It was big, tough, and powerful, yet subdued, not unlike a classic muscle car. The Harley-Davidson V-Rod will be missed. It was the Harley for the non-Harley rider that stood out as proof that the brand was capable of doing something different.

Are there any stoppies on a Harley Davidson?

Nope. Stoppies are not happening with a wheelbase this long, but stopping sure is. Cross-drilled twin discs are grabbed by Brembo calipers controlled by a wonderful ABS system. Photo by Ryan Schultz. Let’s talk a minute about that wheelbase, because it’s the drag racer style of this bike that mostly defines its character.

How can I start my Harley Davidson without a key fob?

Unless you know how to override your Harley Davidson security system by a sequence of things you can to enter your security PIN code, which includes ignition switches, signal switches, and Run/Off switches. Ultimately, this will allow you to start your Harley Davidson without the key fob present and ride on!

What does transport mode do on a Harley Davidson?

Transport mode allows the vehicle to be picked up and moved in an armed state, however, any attempt to start the engine when the fob is not within range will trigger the alarm. We have found that there are different procedures for pre 2014 Harley models and 2014 and above models.

Why does my GM car say no start no crank?

How to diagnose a no start no click on GM vehicle. If you have a late model GM vehicle and turn the key only to hear nothing, you’ll most likely think you have a dead battery—and you may. But a no start, no crank, no click condition can be far more involved than that.

Why does my car not start when I Turn on the ignition?

The most common causes are in the ignition (for example, a bad ignition coil) or fuel system (for example, a clogged fuel filter). However, the source may also be a mechanical fault (for example, a leaking valve), or faulty components in other systems.

Why does my Chevy 1500 turn over but not start?

There could be something wrong with that transition. In older cars this was done by using a low resistance wire in series with the coil primary duing “Start”, then switching (via a solenoid switch) to a higher resistance wire in “Run”.

Navigation