When to turn off the water pump in an RV?
RV water pumps should turn on every time you flush the toilet or turn on a faucet. If after you complete your tasks and turn off the water, and the pump continues to run and run, your RV water pump is likely leaking somewhere. The first thing to do is check for a broken check valve. This valve tells the water pump when to stop.
How do you replace the thermostat on a Ford Ranger?
Remove the wiring harness from the rear of the thermostat (located behind the radiator). Use the socket wrench to remove the thermostat and its gasket. Wipe the are clean with a rag and discard the old gasket. Mount the new thermostat and gasket to the radiator with the torque wrench.
How can I tell if my RV water pump is grounded?
Use a volt meter to check to see if you have a full 12 volts at the pump, then double check that the pump is grounded. (It won’t work if it’s not grounded.) If you have checked all of these issues and you checked the areas mentioned in the first question, then you may need to fully replace the RV water pump.
How to tell if your car water pump needs replacement?
Part 1 of 2: How to tell if a car’s water pump needs replacement. There should be no movement, if there is, this along with the noise is a good indication you may have a water pump problem. Step 5: Check for leaks. It is possible to see signs of coolant leaking before you experience your vehicle’s engine overheating.
How do you change the gasket on a Ford Ranger?
Wipe the are clean with a rag and discard the old gasket. Mount the new thermostat and gasket to the radiator with the torque wrench. The proper torque level for the Ford Ranger is 89 inch-pounds for four-cylinders and 4.0 L V6 engines.
What should the coolant level be on a Ford Ranger?
The proper level for the 3.0 L V6 engine is between 15 and 22 foot-pounds. Replace the drain plug, wiring harness and engine coolant. Reconnect the negative battery cable and start the engine to check for leaks. If there are no leaks, replace the engine brush guard.
Remove the wiring harness from the rear of the thermostat (located behind the radiator). Use the socket wrench to remove the thermostat and its gasket. Wipe the are clean with a rag and discard the old gasket. Mount the new thermostat and gasket to the radiator with the torque wrench.
What should the torque level be on a Ford Ranger?
Wipe the are clean with a rag and discard the old gasket. Mount the new thermostat and gasket to the radiator with the torque wrench. The proper torque level for the Ford Ranger is 89 inch-pounds for four-cylinders and 4.0 L V6 engines. The proper level for the 3.0 L V6 engine is between 15 and 22 foot-pounds.
RV water pumps should turn on every time you flush the toilet or turn on a faucet. If after you complete your tasks and turn off the water, and the pump continues to run and run, your RV water pump is likely leaking somewhere. The first thing to do is check for a broken check valve. This valve tells the water pump when to stop.
What should I do if my water pump is not working?
Now re-establish suction by refilling the water line with water. Connect it again with the pump and turn the pump back on to see if the water begins to move toward the faucets. This could take a couple minutes to be sure the faucets are fully open and have someone watch for the outpour. Anything? D.
Where can I buy a water pump repair kit?
Water pump repair kits and impellers for all other Yamaha outboard motors are available here on Boats.net. NOTE: We recommend you buy the complete Yamaha water pump repair kit, as it includes the various gaskets, O-rings and other parts that usually need replacing when you repair the water pump.
How do you change the trim on a Yamaha water pump?
Step 1. Remove the trim tab by prying off the cap from the foot of the upper casing and taking off the 12mm trim tab bolt beneath it. PRO TIP: Before removing the trim tab, draw a mark across the trim tab and lower casing so you can reinstall it in precisely the same position.