How much does it cost to get a new stator?
Create a Battery-op Ignition System for Less Than $50 The cost of a new stator can be hundreds of dollars. Without a good stator, your engine will run poorly or not at all. This solution completely bypasses the stator by using a 12 volt battery to power the ignition system.
What to do if you have a bad stator?
Without a good stator, your engine will run poorly or not at all. This solution completely bypasses the stator by using a 12 volt battery to power the ignition system. Everything required can be purchased for under $50. It will work on all contact breaker point engines (old style), and some electronic controlled ignition (newer style) ones.
How do you remove a nut from a stator?
1- To remove the nut, the flywheel must be locked in place or else it will simply turn. You can lock it in place by using a special tool. Alternatively, you can lock it this way: remove the spark plug and feed wire or rope down into the cylinder.
What happens when a stator dies on an engine?
While a stator is dying, it can produce a weak spark, causing the engine to miss or run poorly. Symptoms are often worsened as the engine warms up. This needs to be a fairly heavy duty coil. I previously tried using two universal coils intended for small engines.
Is there a way to bypass the stator?
This solution completely bypasses the stator by using a 12 volt battery to power the ignition system. Everything required can be purchased for under $50. It will work on all contact breaker point engines (old style), and some electronic controlled ignition (newer style) ones. The guide is for contact breaker systems.
Where do you put the wire for a new stator?
The wire marked red (coming from the engine) in the diagram is going to attach directly to the contact breaker points. There should already be a wire connected to the breaker points right where we need to put the new one. You need to remove that old wire and put the wire for the new system RIGHT WHERE THE OLD ONE WAS.
What should I do if my Honda stator is weak?
Note that as written this system will bypass the CDI portion of your ignition system (if present) and replace it with a more traditional one. I devised this system when the stator on my Honda XR-100 got so weak that it couldn’t power the spark plug, preventing the engine from running.
Create a Battery-op Ignition System for Less Than $50 The cost of a new stator can be hundreds of dollars. Without a good stator, your engine will run poorly or not at all. This solution completely bypasses the stator by using a 12 volt battery to power the ignition system.
This solution completely bypasses the stator by using a 12 volt battery to power the ignition system. Everything required can be purchased for under $50. It will work on all contact breaker point engines (old style), and some electronic controlled ignition (newer style) ones. The guide is for contact breaker systems.
Note that as written this system will bypass the CDI portion of your ignition system (if present) and replace it with a more traditional one. I devised this system when the stator on my Honda XR-100 got so weak that it couldn’t power the spark plug, preventing the engine from running.
Where does the spark plug go on a stator?
-The two primary terminals on the ignition coil are shared by multiple components, and therefore will have two wires coming out of each. -The raised center terminal on the ignition coil feeds the power that goes to the spark plug. This is where the spark plug wire will connect.
What kind of multimeter do I need to test a stator?
You will need a multimeter set to Ohms for this test. Test every lead of the stator’s connector and note the readings. The reading of each combination should be the same (test leads 1-2, 2-3, and 3-1). If they are different, your stator is defective. Set your multimeter to Ohms.
Without a good stator, your engine will run poorly or not at all. This solution completely bypasses the stator by using a 12 volt battery to power the ignition system. Everything required can be purchased for under $50. It will work on all contact breaker point engines (old style), and some electronic controlled ignition (newer style) ones.
Which is the best site to test a Suzuki stator?
Testing The Stator, a Pictorial Guide Testing The Stator, a Pictorial Guide (by BassCliff) The GS Resources website has a very complete fault finding chart in The Stator Papers available on the In The Garage page. This resource is very useful for understanding and troubleshooting the charging system on these classic Suzuki GS motorcycles.
What should I know about a Harley Davidson stator replacement?
The Harley Davidson stator replacement and upgrade is being done with quality parts made in the USA. The unique design of Cycle Electric Inc. stators offer: Insulation able to withstand temperatures of 600° F to eliminate stator burn out. Better low speed output to reduce battery discharge at an idle.
What should I do if I get a reading on my stator?
Set your multimeter to Ohms. Put the negative lead on the engine’s ground and the positive lead on each wires of the stator’s connector one by one. You shouldn’t get a reading at all. If you get a reading, even very small, on any wire, the stator is defective and must be changed. Put your multimeter to AC Volts and start you vehicle.
You will need a multimeter set to Ohms for this test. Test every lead of the stator’s connector and note the readings. The reading of each combination should be the same (test leads 1-2, 2-3, and 3-1). If they are different, your stator is defective. Set your multimeter to Ohms.
1- To remove the nut, the flywheel must be locked in place or else it will simply turn. You can lock it in place by using a special tool. Alternatively, you can lock it this way: remove the spark plug and feed wire or rope down into the cylinder.
The wire marked red (coming from the engine) in the diagram is going to attach directly to the contact breaker points. There should already be a wire connected to the breaker points right where we need to put the new one. You need to remove that old wire and put the wire for the new system RIGHT WHERE THE OLD ONE WAS.