How do you reset the turn signal on a Dyna Glide?

Press left turn signal switch once, and light will flash a number of times to indicate an error code. There is 1.5 seconds between flashes to indicate 1st and 2nd digit of codes and four second pause between codes. Press and hold left switch down for five seconds, and light will flash twice to indicate the TSSM is reset. Turn ignition to off.

How do you reset the turn signal on a Harley Davidson?

Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice. Press right turn signal switch once, pause, and lights will flash three times.

Why does my turn signal on my Dyna not flash?

I have a ’94 dyna wide glide and whenever I use the turn signals they do not flash, if I hit the right signal it just lights up soild and does not flash and that goes for the left side as well. I went to the dealer and asked what would cause this problem my first guess was a relay but the dealer said it was most likely the turn signal module.

Why is my left turn signal not working?

I have 2005 Road king Classic, the alarm light is coming while riding and the fob is not being touched to arm or disarm the alarm. The light comes on for the alarm and stays on while riding and at that time my right turn signal stops working, the left one still works fine.

How does the turn signal on a Harley Davidson work?

The Turn Signal Security Module monitors the signals and the alarm system for the bike. When there is a problem, the red light key will illuminate. Diagnosing and clearing the codes on each module is really simple, as explained below.

What causes a Harley Davidson to lose all power?

This can be caused by a loose neck or loose spokes (models w/spoke rims). Check your neck and tighten if nessacary. Also, can be caused by a bad wheel bearing. My first thought would be to load test the battery. 10v is low and if it he only gets a clicking when trying to start, that’s one sign of a bad battery.

When was the last time my Harley died?

Yesterday (Thursday) I road her to work, going out after work, and home (~40mi) just fine, nothing out of the ordinary. Figured I was in the clear and it was just some freaky coincidence the day before

Why is my Harley Davidson Dyna Glide not starting?

If your battery voltage and connections are in good condition, but your engine is still refusing to turn over, the problem may be in the starter circuit. Perhaps the easiest place to begin is at the starter solenoid on the right side of the motorcycle.

What should the voltage be on a Harley Davidson Dyna Glide?

Use a voltmeter to measure the available voltage at the battery. A battery that is 100% charged will have approximately 12.6 volts, whereas a battery with a 0% charge will read 11.8 volts or lower. If your battery is low, charge the battery on a setting no higher than five amps for a few hours.

Where is the starter relay on a Dyna Glide?

Starter solenoid electrical connections. Another component to inspect is the starter relay, which is located in the electrical fuse box underneath the side cover on the left side of the motorcycle. Relays have the potential to go bad and prevent high current from reaching the starter.

What kind of engine does a FXD Dyna have?

This bike exists for riders who love a sporty custom ride. Set low in a vibration-damping frame is the Twin Cam 88™ engine, filled to the brim with torque. In 2000, the FXD received a new XR-style flat track handlebar which created a more aggressive stance and performance-minded look and feel.

Where is the Kill Switch on a Dyna Glide?

The kill switch is the button located on the right side of your handlebar, next to the starter button. Position it on the “run” position. Figure 1. Turn kill switch on. Press and hold the trip reset button located on the side of your speedometer. Turn the ignition key to on.

What does the Check Engine light on a Dyna Glide mean?

The check engine light is designed for a reason; it is there to tell you that there is something wrong with your Harley Davidson Dyna Glide. The dealership will charge you over $100 to read and clear the code for you. The good news is, you can do the very same thing for free.

What to do if left turn signal is not working?

If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled. If you apply 12 vdc to the (Lt out) pin -the Left turn signal lights should come on. (you’ve just bypassed the TSM) Next.. connect a jumper from (Lt in)pin to (Lt out) pin & press the Left turn signal switch.

How can I tell if my turn signal module is faulty?

You can pretty much determine if the module is faulty by following the troubleshooting steps outlined in the manual. If you don’t have a manual, then have a look at the TS module and hopefully the pins are labled.

How do you turn off lights on a bike?

This method should work with all bikes built after 2001. Move kill switch to off position, turn ignition on-off-on-off-on. Press left turn signal switch twice, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash. Press right turn signal switch once, pause, and lights will flash twice.

Why does my turn signal keep turning on?

Before resetting the Turn Signal Security Module, you should check some of the basic reasons as to why the red light is turned on. These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse. Fixing these problems could lead to the module clearing its own code.

What kind of turn signal does a Street Glide use?

Akmties Led motorcycle turn signals 1157 front turn signal 2” Bullet Style Running Light Kit Compatible for dyna sportster street glide road king Motorcycle (1157-White+Amber) 4.4 out of 5 stars335 $28.66$28.66

What kind of turn signal does a Harley Davidson use?

PBYMT 1156 LED 2” Bullet Turn Signal Light Rear Brake Bulb Compatible for Harley Davidson Touring Road King Street Glide Electra Glide 1986-2020 4.2 out of 5 stars70 $15.90$15.90

How much does livtee Street Glide turn signal cost?

LivTee Extremely Bright Front Turn Signals & Running Switchback LED Lights Panel with 1157 Base Compatible for Harley Dyna Street Glide Road King, White/Amber 4.4 out of 5 stars674 $29.99$29.99 Get it as soon as Wed, Jun 16 FREE Shipping by Amazon

Why is my hazard light not working on my Harley?

Check the hazard light box and make sure all signal wires are attached. Check the flasher for functionality (turn signal relay). The wiring for the turn signal lights goes through the turn signal switch. This means that the turn signal switch may be bad. If only one light (or one side) isn’t working, check the power to the bulb plug-in connections.

Why is my turn signal not working on my Harley?

These reasons include a dying key fob battery, blown turn signal bulb, or bad fuse. Fixing these problems could lead to the module clearing its own code. Accessing the diagnostics menu requires you to press several of the accessory switches in a very specific manner, within a short amount of time.

Why is there a code on my Harley Davidson?

Codes are helpful when diagnosing an issue with your bike. Sometimes codes can come up from a simple mis-start, a small cough or backfire. A stored code does not necessarily mean that you have an issue that needs attention.

Are there rear running lights on a Harley?

You don’t say anything about year but unless something has changed, rear turn signals on Harley’s have never been running lights unless you add the kit to make them so. Can’t figure it out. Brake light works, rear turns work, but no rear running lights.

When did the Dyna security circuit come out?

MODELS, SECURITY CIRCUIT, SHEET 12 OF 12 2003 ALL DYNA DOMESTIC AND INTERNATIONAL MODELS (Except FXDWG), LIGHTS, INST. & IND., SHEET 2 OF 11

What kind of circuit does a Harley Davidson use?

MODELS, HORN & INSTRUMENTS CIRCUIT, SHEET 8 OF 12 2003 ALL EFI SOFTAIL DOM. and INT. MODELS, HORN & INSTRUMENTS CIRCUIT, SHEET 9 OF 12 2003 ALL EFI SOFTAIL DOM. and INT. MODELS, STARTING CIRCUIT, SHEET 10 OF 12 2003 ALL EFI SOFTAIL DOM. and INT.

Is there a 2003 Dyna Wide Glide for sale?

Up for sale: 2003 100th Anniversary Edition, Dyna Wide Glide. Bike only has 8,205 miles. Bike has had forward controls and taller riser installed to make bike more comfortable for long rides.Bike was just fully serviced, all fluids changed and a new battery just put in. Tires are 80%Only minor wear and tear, bike is in excellent condition.

What does the start button on a Dyna FXDC do?

Alarm, clutch inhibit & neutral safety all come from the TSSM. The TSSM controls the start relay. 09 Dyna FXDC, got power everywhere. Lights,Horn,Turn`s,Fuel Pump,Dash, Turn the key on, hit the run/stop switch, push the start button and Nothing.

What happens when you press the starter button?

Battery is almost fully charged , what I had expected after 4 months of sitting. Also, press starter button with lights pointed on wall nearby no dimming of lights at all. Otherwords no load being put on battery. Will go play with it when it warms up a bit.

What to do when you press the starter button on a V twin?

You can jumper a wire from your battery positive post or the battery post on your starter to your green wire solenoid connection to see if the starter activates (make sure your in neutral and the ignition is shut off). If it does starter is ok and suspect the bad relay.

How to diag a Harley Davidson Dyna Glide?

Press and hold the odometer reset button. Turn the key to “on” and the speedometer will then twist full range, while the rest of the dash lights up. Once the word “diag” shows up, your are in the diagnostic menu.

How to get the menu on a Dyna Glide?

Accessing the menu requires inputting a special code using the following buttons and switches. Turn the key ignition to OFF, and Run/Stop switch is to Run. Press and hold the odometer reset button. Turn the key to “on” and the speedometer will then twist full range, while the rest of the dash lights up.

Where is the DTC module on a Dyna Glide?

Earlier Dyna models may differ in terms of accessing the DTC module. The diagnostics menu is all accessed and read from the digital odometer. Accessing the menu requires inputting a special code using the following buttons and switches. Turn the key ignition to OFF, and Run/Stop switch is to Run.

How does the turn signal work on a Dyna Glide?

This article applies to the Harley Davidson Dyna Glide. There are many modules on your Harley Davidson that track as well as monitor the state of your powertrain and accessories. The Turn Signal Security Module monitors the signals and the alarm system for the bike. When there is a problem, the red light key will illuminate.

What to do if your Dyna Glide won’t start?

Typical Dyna Glide fuse box layout. It usually a good idea to open up the right handlebar switch assembly and check for corrosion on the starter and run switches. While it is not a very common problem, checking for a faulty starter switch is one last area to inspect before setting your sights on the starter assembly itself. Figure 6.

Where is the speed sensor located on a Dyna Wide Glide?

I have a 2007 dyna wide glide, where is the speed sensor located? I do not have a service manual. Behind the transmission top cover and near the starter. Had the same problem on my 2000 ultra. Had to change to what my mechanic called a maxi fuse. The one under the seat left side that has the starter wires to it.

How to turn off the security system on a Harley Davidson?

Press the RIGHT turn signal switch one time and the security system alarm is turned off 1. Select 5 digit code ( each digit being a 1 thru 9) and record it on the wallet card in the owners manual. 2. With an assigned FOB present, turn IGN key ON – OFF – ON – OFF – ON 3. Press left turn signal switch 3 times 4.

When do I use the turn signals, both tail lights blink like hazard lights?

Q: When I use the turn signals, both tail lights blink like hazard lights. Hello! I need help with a tail light problem. This morning I got pulled over and given a warning about one of my brake lights not turning on when I use the brake, so I got home and fixed it doing some rewiring. It worked. Until I noticed the right side didn’t work.

When do I Turn left the turn signal will not turn off?

When I’m turning left and activate the turn signal, and complete the turn the signal will turn off. However, when I’m turning right and activate the turn signal, and complete the turn the signal will not turn off.

Is it illegal to not have a turn signal on a bike?

It’s not a showstopper because you can still ride. But turn signals are an essential part of bike safety. Hand signals are fine during the day, yet are hard to see at night. A broken signal light is illegal in many states. So, don’t let this problem persist. Get those signals fixed as soon as you can.

Why is my turn signal not working on my Road King?

Im going through the same thing right now with my 15 road king, I ordered a new harness got it plugged it in now neutral light comes on with switch turned off or on, everyone said change wiring harness mine signals work but lt turn and high beam don’t, Help Schmiddty? Click to expand… I haven’t run into this problem yet.

Where is the turn signal on a Harley Davidson?

The turn signal module is a grey rectangular module with a grey plug into the front side. It is located under the seat in front of the circuit breaker block. Problem may be the module, but definitely not the ignition module if the bike runs.

Why is the right turn signal light not working?

The right turn signal light and the neutral light does not light. What do you call these indicators lights and where can you get them? Hi William. Those are, simply, indicator lights. They are sealed. There are no bulbs to change for the indicators on your year/model. Usually, when one fails, however, it is due to a bad connection or switch.

Navigation