What kind of engine does a Mitsubishi Lancer Mirage have?
Mitsubishi Lancer – Mirage 96 – 05 with 4G15 1.5 SOHC 12v engine. Dummies Guide to Vehicle Modifications! The Mitsubishi Lancer – Mirage 1.5 model is the base range model and was more commonly known as the GLi model until the recent introduction by Mitsubishi of the GLi 1.8 model for greater power.
When did the Mitsubishi Mirage model come out?
The current Mirage model is a subcompact hatchback and it replaces the Mitsubishi Colt sold between 2002 and 2012. Get notified for new files? We’ll send you a quick email when a new Mitsubishi Mirage document is added.
What was the compression ratio of a Mitsubishi Mirage?
The small turbocharger, of Mitsubishi’s own manufacture, unusually sat between the intake and the twin-barrel carburetor. The engine was equipped with a knock sensor, enabling it to run on petrols of various octane ratings. The compression ratio was also unusual, fairly high for its time at 8.7 to 1.
What’s the backseat split on a Mitsubishi Mirage?
The Fiore was often abbreviated to Lancer or Lancer F in international markets, eschewing the “Fiore” suffix. The sedan’s backseat folded in a 60/40 split, just as for the hatchback.
What kind of engine does the Mitsubishi Mirage have?
Another new version for the Japanese market was the 1600SX, a well-equipped five-door automatic fitted with the 1600GT’s 88-PS engine. At the same time as this facelift, Mitsubishi introduced a four-door sedan variant to Japan under the names Mirage Saloon and Lancer Fiore, which is not to be confused with the unrelated regular Lancer.
When did the Mitsubishi Mirage liftback come out?
The liftback introduced in 1988 complemented the sedan as an additional compact offering, and the coupé of 1991 fitted in with the subcompact range. The current Mirage model is a subcompact hatchback and sedan and it replaces the Mitsubishi Colt sold between 2002 and 2012.
When did the Mitsubishi Mirage Space Star come out?
However, New Zealand sold a very different Mirage from 2002—a rebadged Dutch-manufactured Mitsubishi Space Star labeled Mirage Space Star. This vehicle was not very popular and was discontinued in 2003. Mitsubishi launched the Mirage as a front-wheel drive three-door hatchback in March 1978, as a response to the 1973 oil crisis.
When did the Mitsubishi Mirage 1400 GT Turbo come out?
A more sporting turbocharged 105 PS (77 kW) version of the 1.4-liter engine was made available in Japan from September 1982 as the 1400 GT Turbo. The small turbocharger, of Mitsubishi’s own manufacture, unusually sat between the intake and the twin-barrel carburetor.
What are the trouble codes on a Mitsubishi?
Diagnostic trouble codes may be cleared by disconnecting the battery ground cable for at least 20 seconds. Reconnect negative battery cable and recheck codes to confirm the repair. Oxygen sensor fault. Airflow sensor fault. Intake air temp sensor fault. Throttle position sensor (TPS) fault. Idle speed control (ISC) motor position sensor fault.
When to use 1995 / 96 Mitsubishi diagnostics protocol?
The 1995/96 protocol rides on top of the OBDII stuff, so it is VERY slow, only 7-9 samples per second. So, when logging you should only select 1-2 items at a time. All following info has been verified on my Mitsubishi Galant E33A (4G63 SOHC), but it should apply on other pre-OBDII ECUs as well.
What is the EFI pin for Mitsubishi diagnostics?
<< Pin1 Very important for mitsubishi diagnostics, ensure this is connected to EFI ECU pin 56 (evo4-8). << Pin7 Very important for diagnostics, ensure this is connected to EFI ECU pin 85 (evo9) or pin 62 (evo4-8).
Mitsubishi Lancer – Mirage 96 – 05 with 4G15 1.5 SOHC 12v engine. Dummies Guide to Vehicle Modifications! The Mitsubishi Lancer – Mirage 1.5 model is the base range model and was more commonly known as the GLi model until the recent introduction by Mitsubishi of the GLi 1.8 model for greater power.
<< Pin1 Very important for mitsubishi diagnostics, ensure this is connected to EFI ECU pin 56 (evo4-8). << Pin7 Very important for diagnostics, ensure this is connected to EFI ECU pin 85 (evo9) or pin 62 (evo4-8).
The 1995/96 protocol rides on top of the OBDII stuff, so it is VERY slow, only 7-9 samples per second. So, when logging you should only select 1-2 items at a time. All following info has been verified on my Mitsubishi Galant E33A (4G63 SOHC), but it should apply on other pre-OBDII ECUs as well.
Can You disconnect pin9 on Mitsubishi evoscan cable?
• Yes disconnecting pin9 on the EvoScan Cable with pliers is ecommended for Mitsubishi AYC/ACD usage (pin9 is only used for subaru reflashing) (the reason for removing pin9 is because Mitsubishi ETACS and AYC/ACD ecus will not datalog until pin9 is removed from the 16pin end of the USB cable.)