What are the stop lights on a Mitsubishi Lancer?
Stop lights (Brake lights), ETACS-ECU, high-mounted stoplight, rear combination light and shift switch assembly ETACS-ECU, front door lock actuator, trunk lid actuator and switch and rear door lock actuator
What kind of engine does a Mitsubishi Lancer use?
For the 4B11 engine, the aluminum die-cast cylinder block has been adopted to achieve the top level of this class in high performance, good fuel effi- ciency, while being compact and lightweight.
What was the fourth generation of the Lancer?
A reliable car with many aliases, the Lancer was known and sold under numerous name tags, such as Colt Lancer, Eagle Summit, Mitsubishi Carisma and Mirage to name only a few. 1988 saw the introduction of the fourth generation Lancer, a mor…
What is the CVT on a Mitsubishi Lancer?
Primary pulley speed sensor <CVT>, secondary pulley speed sensor <CVT> and transaxle control module <CVT>
What do you need to know about the Mitsubishi Lancer?
A/C control panel, A/C-ECU, CVT control relay, ABS-ECU, center panel unit, column switch, combination meter, heated seat relay, KOS-ECU, rear window defogger relay, shift switch assembly, SRS-ECU, sunroof motor assembly, wireless control module and receiver antenna module
How to read circuit diagrams Mitsubishi Lancer f90-5?
ACX02361AB TSB Revision f90-5 CIRCUIT DIAGRAMS HOW TO READ CIRCUIT DIAGRAMS Indicates input/output to/from control unit (current flow direction). Input Output Input/ output Indicates a wiring connector which is inside the equipment and which is not shown in the wiring harness configuration diagram.
Where is the inertia switch on a Chevy?
Push the button on the inertial switch; it should be clearly marked as the fuel pump reset, and may be in a contrasting color to the case. You may need to turn the ignition key to the on or accessory position to energize the module and reset the switch.
What is the fuse box on a Mitsubishi Lancer?
Center exhaust pipe heated oxygen sensor, engine control module, engine oil control valve, evaporative emission purge solenoid, evaporative emission ventilation solenoid, injector No.1 to 4, mass airflow sensor, heated oxygen sensor and vehicle speed sensor
What to do when your third brake light is not working?
When the lower lights do not come on and only the third-brake light works, the brake-light switch may be ruled out. Again try the emergency-flashers to check for wiring, socket and lamp problems. If the flashers work, check for blown fuses as a few vehicles use separate circuits for the lower and third brake lights.
What causes brake lights to go out but lower lights work?
If the plunger of the switch does not contact the pedal, check for an adjustment. In rare instances, the brake booster may fail, and the pedal will not rise enough to contact the switch. Pull up on the brake pedal and if the lights go out, switch mis-alignment or pedal position error is the likely cause.
Where is the brake light switch on my car?
Fuse Box and Light Switch. You have to find the fuse box or the power distribution center (PDC). You will get the fuse panel under the dashboard and the PDC under the hood. The brake light switch is also to be found under the dashboard and check if its plunger touches the brake pedal arm.
When the lower lights do not come on and only the third-brake light works, the brake-light switch may be ruled out. Again try the emergency-flashers to check for wiring, socket and lamp problems. If the flashers work, check for blown fuses as a few vehicles use separate circuits for the lower and third brake lights.
If the plunger of the switch does not contact the pedal, check for an adjustment. In rare instances, the brake booster may fail, and the pedal will not rise enough to contact the switch. Pull up on the brake pedal and if the lights go out, switch mis-alignment or pedal position error is the likely cause.
Where are the fuses located on a Mitsubishi Lancer?
Keep in mind that the fuse designations can vary between model years and various trims. Located on the driver’s side of the engine is the main fuse box. The main fuse panel also has several relays. Under the dashboard on the driver’s side are located the interior fuses.
Can a bad brake light cancel a turn signal?
With a bad turn-signal switch, the third-light should still function. On this type system, the turn signals and brakes use the same circuit. When we use the turn signal switch, it cancels the brake light signal, on the side selected.