When is the p0507 GMC diagnostic trouble code set?
The P0507 Diagnostic Trouble Code (DTC) is set when the Powertrain Control Module detects an engine speed outside of the Idle Air Control range of control. Need more information on how to fix the P0507 GMC code?
How do you clear a GMC fault code?
Once you locate the battery, the method for clearing the code is the same, regardless of the year, make or model of GMC vehicle. Fault codes can be set off in a vehicle for a variety of reasons, ranging from a loose gas cap to a major mechanical problem. Turn off the vehicle. Pop the hood by pulling on the hood release under the dashboard.
Where is the negative battery on a GMC?
Locate the battery. The location depends on the make, model and year, but it will be in one of the four corners of the engine bay. Put the adjustable wrench on the bolt that holds the negative battery clamp on the negative battery terminal. Loosen the bolt, and remove the clamp. Hold the negative battery clamp and wait for one minute.
How much does a GMC Sierra 3500HD cost?
RIZZA BUICK GMC CADILLAC, INC. Includes $950 in cash and discounts. CIRCLE BUICK GMC, INC. Includes $1,450 in cash and discounts. WOODY BUICK-GMC, INC. Includes $450 in cash and discounts. Includes $450 in cash and discounts. Includes $950 in cash and discounts.
What are all the trouble codes for GM?
These codes are from PowerTrain series (P0XXX, P2XXX, P34XX), Body Series (B0XXX), Chassis series (C0XXX), Network series (U0XXX, U2XXX, U3XXX). Also there is a list of more than 13500 additional manufacturer specific codes.
Why do I have a p0370 code on my engine?
Possible causes for this P0370 code include: Begin by visually inspecting the engine position sensor and the corresponding wiring. Look for loose connections, damaged wiring, etc. If damage is found, repair as necessary, clear the code and see if it returns. Also, check the engine for any metal particulates that may affect sensor operation.
What is the diagnostic code for a Chevy Duramax?
Below are common check engine light trouble codes for the Chevy/GM Duramax diesel. This list has been updated to includes Chevy/GM Duramax diagnostic trouble codes. At Thoroughbred Diesel we are a real diesel performance and repair shop that offers free advice. Call us at 1-866-737-4966 with any questions you may have about your diesel.
What does the GM code for over 3V mean?
Key on, the PCM detected over 3v on Cruise Direction circuit with Quad Driver turned off. Cold engine startup, then the PCM detected a fault in the PCM pullup resistor used to revise ECT resolution in engine operation. Key on, then the PCM received an unrecognized password from the IPC (controller) or it received a “bad” timing cycle from the IPC.
The P0507 Diagnostic Trouble Code (DTC) is set when the Powertrain Control Module detects an engine speed outside of the Idle Air Control range of control. Need more information on how to fix the P0507 GMC code?
How to read GM OBD diagnostic codes for free?
How to read the codes 1 Ground terminals A and B (see diagram below) with the ignition “ON” and engine not running. The system will enter the… 2 After Code 12 is displayed, any stored trouble codes will be displayed by flashing the “CHECK ENGINE”, “SERVICE… More
What kind of diagnostic interface does a GMC use?
GMC, Holden, Opel, Vauxhall. Most GM cars produced in 1996-2003 use J1850-VPW interface. GM cars produced in 2003-2006 use J1850-VPW interface or CAN. Most cars produced after 2006 are equipped with CAN bus. Since 2002, there is another pinout – GM-LAN (for vehicles equipped with CAN bus) Note that list is not 100% complete!
How many GMC trucks have throttle body injection?
New and Remanufactured Throttle Body Assemblies for 305, 350, 454 Chevy, GM, GMC Trucks, Cars, Vans and 6 Liter and 7 Liter Trucks. Serving our valued customers for over 30 years.