Why does the fuse keep blowing on my ignition switch?
When the circuit is live and the short is present, the bulb will be full brightness and hot so be sure it is not laying on the carpet or against a plastic door panel. Now you can unplug electrical connectors and move things around to see what makes the short go away. When it does, the bulb will get dim or go out.
Why does the 10A IGN fuse keep blowing out?
When the PGM-FI unit goes bad it can blow the 10A ign fuse, don’t know why or how cause they’re sealed and for added insurance, recommend replacing the regulator as well, but as shadetree mentions above check for corroded grounds or open wires first, before blowing 200 bucks for new parts. bad CDI?
What’s the ignition fuse on a Honda 10A?
10A is the ignition fuse. Same thing happened to me couple months ago and I have the same model and year. Kept blowing the ignition fuse, no FI light, no fuel pump, etc. Checked all the wiring, good.
What causes the fuse to fail when I turn the key to the start?
If the WHITE wire coming off terminal “S” is shorted anywhere between the ignition switch and the clutch/brake switch and the attachment clutch and solenoid it will cause the fuse to open/fail or if “clutch/brake switch or “attachment switch is shorted it will cause the fuse to fail/open whenever the key is turned to the start position.
What does it mean when the AM2 fuse blows?
Battery—-AM2 Fuse—-Ignition Switch—-IGN Fuse—-Relays for Ignition Coil and Fuel Pump. So, if the AM2 Fuse is blowing, that must mean there’s a short between the AM2 fuse and the ignition switch, or there’s an internal short in the ignition switch. So now the question is how do I test which it is?
What to do if your fuse blows on your car?
If I change a fuse right after I tried starting the car, it will blow instantly when the ignition is turned to ON. However, if I leave the car sit for a while and replace the fuse, the car will start and run, but only for a few minutes.
What causes a fuse to blow on an ignition switch?
The good news is that there aren’t too many things in the ignition system itself that can blow your fuse, particularly if the the ignition coil draws its current directly from the battery or alternator via a relay. If that’s the case, then your fault is almost certainly in the ignition switch itself or the wires going to it.
If the WHITE wire coming off terminal “S” is shorted anywhere between the ignition switch and the clutch/brake switch and the attachment clutch and solenoid it will cause the fuse to open/fail or if “clutch/brake switch or “attachment switch is shorted it will cause the fuse to fail/open whenever the key is turned to the start position.
Why are the fuses blowing on my computer?
Inspect your wires carefully; hot parts on the engine can easily burn through the wiring’s insulation and short the wires, and metal edges will cut through the wires and short them out. If you’ve got fuel injection, then you might be experiencing an internal short in the computer itself.
Why does my lawn mower keep blowing the fuse?
So every time I turned the key to start mower it blew the fuse. I got a switch with same prong letters in same place on them an problem solved. First make sure the battery is fully charged.
If this power fuse blows only when you turn the key to the START position, remove the 3/8″ terminal wires from the solenoid, then retry (with new fuse installed) turning the key to that START position again. If the fuse still blows, there is a short in the wire leading from the “S” terminal of the ignition switch to the 3/8″ nut solenoid terminal.
What to do when your fuse keeps blowing?
If the fuse blows simply when you turn the key to the ON position, some component or wire is shorted out that leads from (connects to) the “A” (accessory) terminal of the ignition switch. In this case, finding the problem would consist of a matter of elimination…… disconnecting items until the fuse no longer blows.
So every time I turned the key to start mower it blew the fuse. I got a switch with same prong letters in same place on them an problem solved. First make sure the battery is fully charged.
What happens when a fuse blows on an ignition switch?
Insert a new fuse into the holder and turn the key to the run position. Turn the key off and pull out the fuse to see if it blew. If the fuse blows. When you turn the key to the run position, an internal ignition switch contact sends current from the B terminal on the ignition switch to the A1 terminal to energize the blue wire.
How to find the cause of a blown fuse on a riding mower?
The final steps in finding the cause of the blown fuse are to test the blue wires in the wire harnesses. This tractor has wire harnesses for the dash, chassis and engine. Check the dash wire harness first. The dash wire harness. Unplug the engine and chassis wire harness from the dash wire harness.
What should I do if my fuse blew?
If you didn’t measure voltage through the fuse holder with the key turned off, pull the meter probes out of the fuse holder. Insert a new fuse into the holder and turn the key to the run position. Turn the key off and pull out the fuse to see if it blew. If the fuse blows.