How to change the fuse on a 120A Alt?
1 Open the fuse box cover. Remove the ECU cable from the “metal plate” on the left of the fuse box. 2 Open the bolt (red arrow) and unclip the three (yellow arrows) wire connectors. 3 You will need to open the plastic clips from around (outside) the fuse box to separate the lower and upper bodies.
Where is the ECU cable on a 120A fuse?
Remove the ECU cable from the “metal plate” on the left of the fuse box. Makes things a bit easier. Remove the two bolts (10mm) shown by arrows in picture. You will have lift the ECU plate from the front bolt. Step 2: Open the bolt (red arrow) and unclip the three (yellow arrows) wire connectors.
Where is the fuse located on a 120 amp?
As mentioned earlier, the 120 amp fuse is in fact bolted in on each terminal located inconveniently at the underside of the fuseable link. The fuse box has both an upper and lower cover, both must be removed. While you’re at it, remove the battery, the lower portion of the air filter and the module thingy attached to the side of the fusebox.
Where is the alt’s fuse on a Toyota?
The “ALT-S” fuse is the charging system fuse. Step 6 Locate the fuse removal tool within the fuse box. The fuse removal tool is a plastic set of tweezers held in place with a plastic clip.
As mentioned earlier, the 120 amp fuse is in fact bolted in on each terminal located inconveniently at the underside of the fuseable link. The fuse box has both an upper and lower cover, both must be removed. While you’re at it, remove the battery, the lower portion of the air filter and the module thingy attached to the side of the fusebox.
What kind of Fuse is 120 amp alternator?
It must’ve been brief, because I didn’t see/hear/feel a spark. So the 120 amp fuse for the alternator is a PAL type fuse, and it is a bit of a PIA to remove. I’m a mechanic, so it wasn’t very difficult for me, just time consuming.
Remove the ECU cable from the “metal plate” on the left of the fuse box. Makes things a bit easier. Remove the two bolts (10mm) shown by arrows in picture. You will have lift the ECU plate from the front bolt. Step 2: Open the bolt (red arrow) and unclip the three (yellow arrows) wire connectors.
What should I do if my Honda fuse blew?
Unhook negative battery cable to be safe, remove two screws holding this in, and then you can wiggle it up and out. Reverse procedure to replace. Also check your other under-hood fuses when replacing this. When I blew this also blew two other fuses in the small underhood fuse box.
Where is the blown fuse on a Mazda Protege 5?
SOURCE: Blown main fuse on 2003 mazda protege 5. There are two bolts on the side of the fuse itself. Under the fuse box on each side. Unbolt those and it will come out. You can’t post conmments that contain an email address.
Is there a 120A fuse on the battery terminal?
Discussion in ‘ FX (03-08) – Electronics & Lighting ‘ started by tchuck, Jan 9, 2012 . So at some point during the course of the installation of my headers I managed to blow the little 120A fuse that is on the positive battery terminal.
SOURCE: Blown main fuse on 2003 mazda protege 5. There are two bolts on the side of the fuse itself. Under the fuse box on each side. Unbolt those and it will come out. You can’t post conmments that contain an email address.
Unhook negative battery cable to be safe, remove two screws holding this in, and then you can wiggle it up and out. Reverse procedure to replace. Also check your other under-hood fuses when replacing this. When I blew this also blew two other fuses in the small underhood fuse box.
How do you remove a fuse box from a car?
Once the lid is off and set aside, find and disconnect the power supply to the fuses. There is a possibility the power supply is routed through the bottom. In that case, skip to step 4 to remove the fuse box housing to access the wires, and then come back to step 3 before proceeding.
The “ALT-S” fuse is the charging system fuse. Step 6 Locate the fuse removal tool within the fuse box. The fuse removal tool is a plastic set of tweezers held in place with a plastic clip.