How to replace a Mercury Sable speed sensor?
Pull the sensor out. If you have trouble removing the sensor after the bolt has been removed, use a screw driver to pry the sensor out. Take the new sensor and place it in the slot where the old sensor sat. Put the sensor in place by lining up where the bolt will be wrenched into place.
Where can I find the transmission speed sensor?
Drive the vehicle around the block to see if the speedometer will operate. Step 2: Check under the vehicle. When returning from the test drive, grab a flashlight and go under the vehicle. Look for the transmission speed sensor and see if the harness is attached and secured. Step 1: Park your vehicle on a flat, hard surface.
What’s the best way to replace a wheel speed sensor?
Step 1: Prepare your work area. Make sure the vehicle is on a level, safe surface, and you have set the parking brake. Step 2: Loosen the lug nuts. Use a ½ inch drive breaker bar and a lug nut socket set to loosen all the lug nuts before you jack the vehicle up in the air.
What happens if the speed sensor comes off?
If the magnet comes off the speed sensor, it will lodge itself into the transmission making a grinding noise. Depending on how the sensor failed, an engine light will illuminate to inform the driver that there is a problem. Step 1: Turn on the ignition and start the engine. Drive the vehicle around the block to see if the speedometer will operate.
Pull the sensor out. If you have trouble removing the sensor after the bolt has been removed, use a screw driver to pry the sensor out. Take the new sensor and place it in the slot where the old sensor sat. Put the sensor in place by lining up where the bolt will be wrenched into place.
How do you remove a speed sensor from a car?
The electrical cord that is connected to the vehicle speed sensor will need to be removed. You can do this easily by pinching the end of the cord so it releases its grip on the sensor. Pull it straight off and let it hang. With the electrical cord removed you can now screw out the sensor.
When to replace the speedometer in your car?
If you notice that the speedometer does not work any longer, replace the vehicle speed sensor as it is the most likely cause. It is important to make sure that you purchase the correct vehicle speed sensor for your car.
How do you replace ABS wheel speed sensor?
Pull up the metal C clip and unplug the old sensor from the connector. To get to the connector, you may have to remove the wheel well liner. Separate the two connectors. You will need a small screwdriver to pry out the clips and separate the ABS and brake pad wear sensor.
How do you replace a vehicle speed sensor?
Use a rag and clean out the threads of the sensor housing. Set the new vehicle speed sensor into the threaded area and make sure it is straight. Start to tighten it by hand. Once it gets snug, use the wrench again to tighten it a few more turns.
If you notice that the speedometer does not work any longer, replace the vehicle speed sensor as it is the most likely cause. It is important to make sure that you purchase the correct vehicle speed sensor for your car.
How do you remove a motion sensor from a car?
With the electrical cord removed you can now screw out the sensor. Use a socket, or open end, wrench and twist the sensor in a counterclockwise direction. Be careful not to put too much pressure on it or it will break off in the threads. Continue to loosen the sensor up until you can remove it.
What’s the price of a 2008 Mercury Sable?
The 2008 Mercury Sable’s Manufacturer’s Suggested Retail Price (MSRP) starts just a little under $25,000. Adding AWD adds about $1,800 and the more up-market Premier trim with AWD comes in a little over $30,000, and up to about $35,000 when fully-loaded.
Are there any problems with the Mercury Sable?
The 2008 Mercury Sable has 73 problems & defects reported by Sable owners. The worst complaints are steering, accessories – interior, and engine problems.
When was the Mercury Sable front wheel drive introduced?
Introduced on December 26, 1985 as the replacement for the Mercury Marquis, the Sable marked the transition of the mid-size Mercury product range to front-wheel drive. For its entire production life, the Sable served as the Mercury counterpart of the Ford Taurus (no Sable equivalent of the Taurus SHO was ever produced),…