When to replace idle control motor in Ford?
Fords are designed to operate with the resistance in the solenoid in a range between 7.0 to 13.0 ohms. If the resistance is outside that range, the idle control motor needs to be replaced.
What to do if your fuel pump fuse is blown?
Check in your owner’s manual for the location of the fuse box, then find the fuse that corresponds to the fuel pump. Pull it out and inspect it for signs of failure. If the fuse is blown, it will be broken or burned.
How to troubleshoot the fuel pump on a 50 hp Johnson?
Remove the inline fuel filter with pliers. Turn on the air compressor and blow out the line with a hand-held air attachment. Attach a new inline fuel filter to the line. Attach the line back to the gas tank and the carburetor. Also use a screwdriver to pry the fuel pump bulb off of the fuel pump.
What should I do if my fuel pump needs replacing?
If your fuel pump does needs replacing, a rebuilt one is often as good as a new one, and a lot less expensive. If you’re feeling adventurous, some manufacturers supply rebuild kits. You can take your pump apart with a screwdriver and rebuilt it yourself, following directions on the kit.
Where does the fuel go in a Mercedes 190E?
With the cover removed you can see how the fuel flows from the tank to the engine. The main supply line comes from the tank and enters the first pump (yellow arrow), it exits the first pump (red arrow and enters the second pump (purple arrow), the fuel then exits the second pump (blue arrow) and is sent to the fuel filter.
When to re-wire a fuel pump off a relay?
Contributed By: Enginebasics.com When putting in an aftermarket fuel pumpor looking to get more fuel out of your factory pump, one mod worth doing is re-wiring that fuel pump.
When do you need to change your fuel pump?
Your fuel pumps are an integral part of the fuel delivery system. A clogged or faulty pump can cause all kinds of problems, from a rough running engine to leaving you stranded on the side of the road. It is a good idea to change your pumps at the first signs of it going bad (trouble starting).
Where is pin 86 on a fuel pump?
Being that pin 86 is wired straight to the battery this will send a nice, clean voltage straight to the battery with no other obstructions to the fuel pump.
How can I tell if my idle control valve is working?
To check if an idle control valve is working properly, start by turning on your engine and letting it run for a minute or 2. Then, when it’s at an idling speed, take note of the RPMs in your car. Next, turn the engine off and disconnect the idle control motor under your hood.
What does it mean when your engine idle does not increase?
Use the command in the scan tool to increase the engine’s idle. If the engine idle does not increase, it means there is an issue at the idle control motor of its circuit preventing the signal from changing the idle. You can purchase a bidirectional scan tool at your local auto parts store.
What happens when the idle control motor is disconnected?
With the Idle Control Motor disconnected, get back into the vehicle and start the engine again. The engine should still start and run without any issue despite the idle control motor being disconnected. Be sure to tuck the wiring you disconnected up in the engine bay so it doesn’t get caught in any moving parts.
How to troubleshoot an automotive engine high idle?
The troubleshooting procedure for high and low idle conditions are similar, which are included in the following: Step 1 – If the check engine or service engine light soon has illuminated retrieving the diagnostic trouble codes could lead you in the right direction of what the problem is, or is related too.
Can a bad throttle position sensor cause idle surging?
Idle surging can be caused due to other issues in the car, but if it happens in conjunction with other throttle position sensor symptoms, the culprit is often the TPS. At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. 3) Check Engine Light
The troubleshooting procedure for high and low idle conditions are similar, which are included in the following: Step 1 – If the check engine or service engine light soon has illuminated retrieving the diagnostic trouble codes could lead you in the right direction of what the problem is, or is related too.
What causes the Check Engine light to turn off at idle?
At idle, the ECM will not get the correct information and the throttle will variate randomly causing idle surges. The check engine light will randomly turn on and off even if the car is running smoothly without any jerks and stalling.
When to remove an idle air control valve?
Because of the nature of this valve (large air volume processed) it should be serviced when a tune up is performed to remove “coking” which will hinder the valve’s performance. To perform a rough check of the idle air control, remove the valve while reconnecting the wiring harness.
Fords are designed to operate with the resistance in the solenoid in a range between 7.0 to 13.0 ohms. If the resistance is outside that range, the idle control motor needs to be replaced.
What does it mean when your engine idle is too low?
If your idle is too low, it could be the IAC not talking to the computer correctly. Disconnect the IAC connector for a couple seconds while your engine is idling. If your engine idle didn’t change, you can suspect it to be the IAC. If it is working properly, unplugging it would cause your idle to freak out.
Can a bad idle control valve cause stalling?
This is controlled by the engine’s computer. Sometimes parts go bad, which results in your car idling strangely or stalling. Check to see if your idle control valve is functioning properly before attempting to replace it. Look for a high engine idle. A common symptom of a faulty idle control valve can be a high idle.
With the Idle Control Motor disconnected, get back into the vehicle and start the engine again. The engine should still start and run without any issue despite the idle control motor being disconnected. Be sure to tuck the wiring you disconnected up in the engine bay so it doesn’t get caught in any moving parts.