What should I use to reset the Dashboard Light on my Mercedes Vito?
If you need to reset a dashboard light or diagnose a fault on your Mercedes Vito/Viano we recommend the Mercedes iCarsoft i980.
What does the fuel warning light on a Vito mean?
It will allow you to read live data such as throttle position, IAT, o2 sensor 1, o2 sensor 2, o2 sensor 3, o2 sensor 4, RPM, fuel trim, coolant temperature, transmission fluid temperature and much more. Mercedes Vito/Viano 639 Mk2 water in fuel warning light – this symbol indicates that water has made its way into the water seperator.
How to diagnose a Mercedes Vito parking brake fault?
To diagnose glowplug faults you can use the Mercedes iCarsoft i980. It might not be the glowplugs but it might be the glowplug module/ECU. The i980 kit will allow you to read & clear fault codes and turn off the dash warning light. Mercedes Vito/Viano 639 Mk2 (P) PARK warning light – indicates that the parking brake is in the ON position.
What does the coolant warning light on a Vito 639 mean?
Mercedes Vito/Viano 639 Mk2 coolant warning light – the coolant symbol like this means that the temperature is too high and you should pull over immediately and not drive any further to prevent engine damage.
What are the warning lights on a Mercedes Vito?
On start up I had two warning lights, glowplug light on (always) and the EDC light on (always). The glow plugs have current for the heat up process and then there is no currnet to them after a couple of seconds so performing properly but the light remains on.
Why does my Vito CDI 110 2000 shut off?
Hi My Vito CDI 110 2000 has Shut off Fault Code, Boost Pressure Code. 7.5a ECU Fuse causes grey smoke rough running when inserted. Merc Star Can not communicate with the CDI. Van starts and runs ok without the 7.5a fuse but in limp mode. Help.
Are there any problems with the Mercedes Vito ECU?
Similar problem with the bas brake assist, had it diagnosed, replaced g force sensor and brake sensor, as that what fault codes came up, reset it, but light is back on!! Spent allot of money on original parts, and it is still the same, could it be the ECU it’s self?
Why is the EDC light always on in my Vito?
The wires in question run from a plug attached to something on the left had side of the engine (as you look at it) down by the alternator up to the wiring loom which runs across the rocker cover, not sure quite where they go to. Click to expand… Me too, i have same problem, EDC light always on.
What do the warning lights on a Vito mean?
Tire Pressure Monitoring System/Flat Tire Monitor Symbols, indicate that the inflation on one of the tires is down 25% or more. If your are at high speed, reduce your speed. For other dashboard Mercedes-Benz Vito warning lights you can read: Automobile dashboard RED warnings lights symbols.
What does the low coolant symbol on a Mercedes Vito mean?
Mercedes Vito/Viano 639 Mk2 coolant level low – this is the low coolant level symbol in the Mercedes Vito/Viano 639 Mk2 and indicates that you should top up your expansion tank as soon as possible with coolant to prevent the engine from overheating and causing damage.
Tire Pressure Monitoring System/Flat Tire Monitor Symbols, indicate that the inflation on one of the tires is down 25% or more. If your are at high speed, reduce your speed. For other dashboard Mercedes-Benz Vito warning lights you can read: Automobile dashboard RED warnings lights symbols.
Where is the coolant temperature sensor on a Mercedes Vito?
The coolant temperature sensor is located on the front of the thermostat. This is on the left hand side of the engine bay tucked in behind the oil filter and near the alternator. Easiest access is through the front – pop the grill off and you can get your arm in.
What is the fault code for the Vito oil sensor?
Have fault codes P1482 (glow) P2006 (mainifold air control) P1470 Boost Pressure P1188 ( Piston cutoff solenoid) and P1192 oil sensor but the last 2 only show up if I plug in Fuse 23. (ecu feed ) Engine fan then comes on an van will rev irratic to 1500rpm up and down like a misfire. Without fuse 23 it runs ok but in limp mode.
Is the CCS sensor on the Vito too sensitive?
If you put the correct amount in ccs according to the manual it would be fine and the level would be bang smack in the middle of the full and low marks . So you have to ask the question is the sensor on the vito too sensitive or is the dipstick just slightly inaccurate did someone get it wrong and not allow for the expansion of oil.
How to check the Mercedes Vito Viano 639 Mk2?
Mercedes Vito/Viano 639 Mk2 LIVE DATA – to retrieve live data stream from your Mercedes Vito/Viano 639 Mk2 we highly recommend using the Mercedes iCarsoft i980 diagnostic kit.
What should I do if my Mercedes Vito has an ABS warning light?
You should use a diagnostic tool which covers the airbag system such as the the Mercedes iCarsoft i980. The kit will tell you where within the airbag system the fault is occuring, and also allow you to clear the dashboard airbag light. Mercedes Vito/Viano 639 Mk2 ABS warning light – indicates a problem within the ABS or Anti Lock Braking System.
What does the warning light on Vito 639 SRS mean?
Mercedes Vito/Viano 639 Mk2 SRS airbag warning light – indicates a problem within the airbag system and needs to be checked out ASAP. You should use a diagnostic tool which covers the airbag system such as the the Mercedes iCarsoft i980.
Mercedes Vito/Viano 639 Mk2 LIVE DATA – to retrieve live data stream from your Mercedes Vito/Viano 639 Mk2 we highly recommend using the Mercedes iCarsoft i980 diagnostic kit.