How do I fix error code H6 on Daikin?
Re: Daikin H6 error You could try switching the power off to the outdoor unit, wait 3 minutes and then turn it back on. You might be lucky and the system will reset itself. H6 is “compressor motor overcurrent sensor is abnormal.”
How do I fix H6 error in AC?
H6: Indicates a fan motor malfunction. Try restarting the unit to see if the error code will disappear. If it does not, please contact a qualified professional for service. E5: Indicates a communication error between the indoor and outdoor units.
What does H6 mean in Gree AC?
Gree AC Error Code: H6. The feedback terminal of PG motor is not connected tightly. The control terminal of PG motor is not connected tightly. Fan blade rotates roughly due to improper installation. Motor is not installed properly and tightly.
What does Voltas AC H6 mean?
More videos on YouTube
| Error Codes | Problem |
|---|---|
| H6 | PG motor does not operate ( indoor fan motor) |
| HC | PFC overcurrent malfunction |
| L9 | High protection of power |
| LP | Indoor and outdoor units cant match with each other |
Why does my air conditioner say error?
The typical error codes can display for a variety of reasons including communication faults between the outdoor and indoor units (usually due to burnt out or faulty PC boards), blocked filters or low refrigeration gas charge.
What causes E3 error in AC?
An E3 error code occurs when the fan speed of your MRCOOL DIY Ductless Mini Split air handler is too low for a certain amount of time. This could be due to a wiring mistake, faulty fan assembly, faulty fan motor, or a faulty control board.
What is compressor drive error?
A P4 error code is caused by an error in the compressor drive. This error code is could be caused by a faulty outdoor board, a faulty outdoor fan motor or a compressor malfunction.
How to erase diagnostic trouble codes in Mercedes medic?
Proceed to ERASING DIAGNOSTIC TROUBLE CODES. 1) After display window shows “En° d”, press AUTO push button once again. Display window should show “dE L” (delete). 2) To erase DTCs, simultaneously press down and up arrow push buttons for more than 5 seconds.
How to delete a / C Diagnostic Trouble Codes?
Proceed to ERASING DIAGNOSTIC TROUBLE CODES. 1) After display window shows “En° d”, press AUTO push button once again. Display window should show “dE L” (delete). 2) To erase DTCs, simultaneously press down and up arrow push buttons for more than 5 seconds. The display window should show “- –“. If not erasing DTCs, press the AUTO push button.
What’s the fault code for a 2001 Mercedes Benz?
Click to expand… For the ML class it does not apply to the 2001 models. Also the fault code in the bulletin is for DTC B9103 and DTC B9123. No others would be covered by the DTB. Post # 34 in this thread lists the DTB the parts, and all affected models.
How to check Mercedes Benz air conditioner trouble codes?
Push the left “AUTO” button to scroll forward and right auto button to scroll back. Depress right AUTO switch repeatedly. Note trouble codes Purchase a larger refill can of 134a with a gauge on it so you can read the low side pressure – helps as a guide to filling the system to the correct level.
Proceed to ERASING DIAGNOSTIC TROUBLE CODES. 1) After display window shows “En° d”, press AUTO push button once again. Display window should show “dE L” (delete). 2) To erase DTCs, simultaneously press down and up arrow push buttons for more than 5 seconds.
Proceed to ERASING DIAGNOSTIC TROUBLE CODES. 1) After display window shows “En° d”, press AUTO push button once again. Display window should show “dE L” (delete). 2) To erase DTCs, simultaneously press down and up arrow push buttons for more than 5 seconds. The display window should show “- –“. If not erasing DTCs, press the AUTO push button.
Why is my a / C compressor not working on my Mercedes?
One other reason why the A/C compressor does not engage is the fact that the system may be low on R134 refrigerant. Typically older cars may have very slow leaks that may require top off with refrigerant every couple of years. You can use a R134a recharge kit to recharge your system if the A/C compressor is not working.
Push the left “AUTO” button to scroll forward and right auto button to scroll back. Depress right AUTO switch repeatedly. Note trouble codes Purchase a larger refill can of 134a with a gauge on it so you can read the low side pressure – helps as a guide to filling the system to the correct level.