How long is the drive cycle for a Mercedes?
2. On-Board Diagnostic System (OBDII) used on the vehicle, are ME1.0, ME2.0 or ME2.1 systems. 3. Performing the drive cycle on the vehicle will take up to 1 1/2 hours. 4. Required tools are: SDS equipment and all required cables. Readiness/function codes cannot be displayed for tests performed on vehicles at altitudes above 8200 feet.
Can a 2002 Mercedes Benz drive cycle be incomplete?
Also, one customer with a 2002 Mercedes was unable to complete the secondary air injection monitor until one evening he allowed his vehicle to idle for 5-20 minutes in his driveway. He then turned off his vehicle and restarted the vehicle the next morning and allowed it to idle for another 5-10 minutes.
How to reset a Mercedes air conditioning system from Japan?
To be on the safe side, hold them until their LED lights start flashing. Step 3: Wait for about a minute for the LED lights to stop flashing. When they do, turn the car off. Wait one more minute before restarting the engine. The AC system is reset now and the hot air blowing problem is likely to be solved.
When to disengage the a / C clutch on a Mercedes?
Purpose of the A/C Compressor Clutch. If no problems are detected such as low refrigerant in the system, it sends a signal to disengage the A/C compressor clutch. Otherwise the A/C compressor engages and starts to compresses the refrigerant. By compressing the refrigerant we add pressure to the system.
When did the Mercedes Benz GL450 come out?
Times have changed for these mechanical bovines from when nearly a million Americans bought them every year. In 2013, the class managed only about 350,000 sales. But the GL is a survivor. This second-generation GL, which arrived for the 2013 model year, has been outselling the Cadillac Escalade and Lincoln Navigator combined.
How long does it take to get to 60 mph in a GL450?
Powertrain performance was never a concern. The 5855-pound GL450 got to 60 mph in 5.9 seconds at the beginning of its stay with us, and dropped an insignificant tenth of a second to 5.8 seconds after 40,000 miles. The quarter-mile remained a steady 14.4 seconds from beginning to end.
What kind of car is the Mercedes GL Class?
Mercedes-Benz GL-Class. Jump to navigation Jump to search. The Mercedes-Benz GL-Class is a full-size luxury SUV produced by Mercedes-Benz since 2006. It is a three-row, seven-passenger vehicle positioned above the GLE-Class, and is the flagship of the Mercedes-Benz SUV line. The GLS shares the same unibody architecture with the GLE-Class.
Where do the Buffalo roam Mercedes Benz GL450?
Where the Buffalo Roam: Racking up 40,000 on this big, brown beast. Like its spirit animal, the massive, majestic American buffalo, the American-made Mercedes-Benz GL450 is ideally suited to the wide-open spaces of our vast continent, where it can roam widely, consuming a vast amount of natural resources.
What happens at the end of the drive cycle test?
The last step of the general drive cycle test is to complete a final OBD-II scan for trouble codes. This is something that will verify that the drive cycle test has been completed successfully. Sometimes a drive cycle test will discover other hidden emission problems that did not register initially.
How to check for incomplete readiness on a Mercedes?
If using a Hand-Held Scan Tool verify Step 3 test completion. This will be indicated by a check mark in the 4. Self-adjustment of the air/fuel mixture (idle speed & self adaptation) (do not interrupt this applied to the vehicle, i.e. Air conditioning OFF) for 3 minutes.
How long does a Mercedes Drive Cycle take?
Lambda (02) Sensor Signal (do not interrupt this portion of the test, to be conducted directly after • Drive vehicle for 3 minutes at 70km/h (43 mph). • After the 3 minutes has been reached proceed to step 3 below.
Also, one customer with a 2002 Mercedes was unable to complete the secondary air injection monitor until one evening he allowed his vehicle to idle for 5-20 minutes in his driveway. He then turned off his vehicle and restarted the vehicle the next morning and allowed it to idle for another 5-10 minutes.
What to do when the drive cycle won’t start?
But if the oxygen sensor and catalyst monitor are ready, then the heater has to be working or the other two monitors would fail and set codes. If the EVAP monitor is not ready, verify that your fuel cap is tight and the level of fuel is between 1/4 and 3/4 full. If all the other monitors are ready, then do a couple more “cold” starts.
What to know about Mercedes Benz 320 CLK drive cycle?
EVAP MONITOR – Fuel System Leak test (EVAP): No DTC codes should be present in memory for the EVAP canister purge valve, fuel tank pressure sensor, or the shut-off valve. – The engine temperature less than 100°C with air intake temperature less than 45°C.