Why is the SRS light flashing on my Mercedes Benz?
SRS stands for Supplemental Restraint System, any it is refered as the SRS or Airbag Warning Light. This could be because the AirBag Control Unit is not programmed correctly. SRS Control Unit is not parameterized or as some may refer taught-in. This can cause the blinking of the airbag / SRS light on the instrument cluster.
How to reset SRS / airbag light on Mercedes Benz?
Find the port that fits the OBD cable and plug the scan tool’s cable into this port. 2. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts. Look at your OBD scan tool and write down the codes it displays. 3. Check your owner’s manual for what the codes mean. 4.
What causes the SRS airbag light to stay on?
Check the belt buckle. The red buckle release on the driver and passenger seat. Loose contact may trigger the airbag light. If the light is triggered it will stay ON and needs to be reset using one of the scanners below. Steering Wheel Clockspring Ring. Can cause the AirBag / SRS light to stay on.
Why is the airbag light blinking on my Mercedes?
In some of the older Mercedes-Benz models, a blinking airbag light could be due to the age of the airbag or loose connections to the airbag components.
Find the port that fits the OBD cable and plug the scan tool’s cable into this port. 2. Put the key into the ignition and turn it to the “Run” position. This is the position just before the engine starts. Look at your OBD scan tool and write down the codes it displays. 3. Check your owner’s manual for what the codes mean. 4.
Why is the SRS warning staying on on a Mercedes Benz?
Why is the SRS warning staying on? Here is a list of some of the most common problems with the SRS system on a Mercedes Benz. Seat Occupancy Senor in the passenger seat. Low voltage in the electrical system. Battery issue or charging. Seat belt latch. Damaged Wire Contacts at the doors. Defective, damaged or loose contact at the impact sensors.
Why does the SRS / airbag light stay on?
Very often the SRS/Airbag light goes on mainly because of a dying battery. But, if the light is on, it will stay on when you install a new battery, until you manually reset it. That is, 2 steps to solve SRS/Airbag light on. Install a new battery; Reset SRS/ Airbag light.
Why is the SRS light on my SL500 not working?
The most common fault is the SRS connections under the passenger seat, all the yellow plugs and 1 each side. often just disconnecting the plugs and spraying with a non drying switch cleaner will fix the problem, but once the lamp is on the car usually has to go onto STAR or other to turn the warning off.
What are the fault codes for Mercedes SRS?
Child seat:”Signal” transmission fault between front passenger seat and “Babysafe” Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. C1011. BAS light, play in steering column causes steering angle sensor to lose memory (?) C1401.
Where is the yellow connector on a Mercedes SRS?
There is a yellow connector beneath the seat, this houses all the connections to the seat pad sensor and links its signals to the ABCM.
SRS stands for Supplemental Restraint System, any it is refered as the SRS or Airbag Warning Light. This could be because the AirBag Control Unit is not programmed correctly. SRS Control Unit is not parameterized or as some may refer taught-in. This can cause the blinking of the airbag / SRS light on the instrument cluster.
Child seat:”Signal” transmission fault between front passenger seat and “Babysafe” Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. C1011. BAS light, play in steering column causes steering angle sensor to lose memory (?) C1401.
What are the fault codes for Mercedes airbags?
Call us at 888-779-9029 M-F 9-5 EST Review the table below for information on Mercedes airbag fault codes: The cause is the cable routing under the passenger seat. The wire was dressed from the factory such that the cabling to the connector was under tension.