How do you replace brake pads on a Mercedes C class?
The process for the rear is similar to the front, although there are some keys differences: There are metal clips that keep tension on the brake pad that must be removed from the caliper. There are two bolts (sliding pins) that require a t45 socket to be removed. There are rubber boots that cover these bolts.
How much does it cost to change brake pads on a Mercedes?
The typical cost to change Mercedes-Benz rear brake pads yourself averages $100. The average cost to change the brake pads at an auto mechanic or dealer range between $250 and $500. If you plan to replace the rotors, the cost would be two to three times more than just changing the brake pads.
How do you remove SBC brakes from Mercedes?
Recommended method: Deactivate the SBC brake system using Star Diagnosis Mercedes-Benz, which these days you can order on eBay, if your car has SBC brakes. Alternative method: You can disconnect the SBC brakes by unplugging the wire harness to the ABS pump.
Can a Mercedes Benz brake system be disabled?
If your Mercedes-Benz has an SBC brake system (common on early E-Class W211 and CLS models), it should be disabled before you work on the brake system. Recommended method: Deactivate the SBC brake system using Star Diagnosis Mercedes-Benz, which these days you can order on eBay, if your car has SBC brakes.
Do you need to replace the brake pads on a Mercedes clk350?
This guide provides instruction on how to replace the rear brake pads on a Mercedes-Benz W209 CLK350 2006-2009. These instructions apply to the following Mercedes-Benz W209 CLK models. Hammer. Yes you will need one. W209 Rear Brake pads. Ceramic Recomended 003 420 27 20 0034202720 W209 Rear Brake Pad Wear sensors. Brake pad anti-squeal grease.
The typical cost to change Mercedes-Benz rear brake pads yourself averages $100. The average cost to change the brake pads at an auto mechanic or dealer range between $250 and $500. If you plan to replace the rotors, the cost would be two to three times more than just changing the brake pads.
Where are the brake pads on a Mercedes C class?
This is where the caliper piston meets the back of the brake pad, and where the brake pads slides onto the metal clips that snap onto the caliper bracket. Your brakes pads may be directional and marked with an arrow. Install the arrows in the direction of wheel rotation unless the directions say otherwise. Figure 17.
Where is the brake fluid located on a clk350?
Open the hood and remove the cap from the brake fluid reservoir. This will allow the brake fluid to return into the reservoir when you press the pistons into the brake caliper. Note the location on the right top corner marked with “Brake Fluid”. Location of power steering fluid, coolant, brake fluid and windshield washer.
The process for the rear is similar to the front, although there are some keys differences: There are metal clips that keep tension on the brake pad that must be removed from the caliper. There are two bolts (sliding pins) that require a t45 socket to be removed. There are rubber boots that cover these bolts.
Where are the brake rotors on a Mercedes Benz?
Identification of the braking system components. To determine if your brake rotor is in specification, locate the minimum thickness stamp on the rotor. It may be on the front, back, or side. The spec will most likely be listed in millimeters.
How to replace front brake pads and rotors?
Measuring rotor thickness. To make this how-to more organized, the front brake pad and rotor replacement will be covered first. Lift your vehicle up and support it on jack stands. Your W204 has several jacking points that can be used, including the rear differential, the front subframe and the side jack stand mount pads.
How do you remove rotor from Mercedes C class?
Remove the Torx bolt. The rotor will now wiggle off the hub; pull towards you as you wiggle. If the rotor is stuck, use the mallet to break the rotor free. You will have to tap the middle section of the rotor. Figure 16. Tap the rotor at the circled areas to remove it. Installation is the reverse of the removal.
Measuring rotor thickness. To make this how-to more organized, the front brake pad and rotor replacement will be covered first. Lift your vehicle up and support it on jack stands. Your W204 has several jacking points that can be used, including the rear differential, the front subframe and the side jack stand mount pads.
Remove the Torx bolt. The rotor will now wiggle off the hub; pull towards you as you wiggle. If the rotor is stuck, use the mallet to break the rotor free. You will have to tap the middle section of the rotor. Figure 16. Tap the rotor at the circled areas to remove it. Installation is the reverse of the removal.
What should I use to clean my brake pads?
Clean the rotor and caliper by spraying it down with brake cleaner. This helps keep the brakes from becoming noisy. Be careful not to spray brake cleaner on rubber (brake line, caliper piston boot, dust covers, etc). Apply disk brake pad grease on the contact areas of the brake pad.
When to replace the front brake pads on a Mercedes C Class W203?
We took this video to show you how to replace the front brake pads on a Mercedes C Class W203. This is almost the same procedure for all w203 which includes c180, c200 c230 c240 c270 c320 and more. It includes: 2001, 2002, 2003, 2004, 2005, 2006, 2007 year models. Please LIKE and SUBSCRIBE for More DIY Videos!!! 5 NEW VIDEOS Every Week!!!
When to replace brake pads and rotors step by step?
When worn, old brake hardware creates vibrations that is heard in the form of brake noise at low stopping speeds. These clips should be replaced with each brake job. Make sure to apply brake lubricant at the slider contact points before installing the hardware. Note the wear-sensor position orientation to install the pads correctly.
What to do when your brake pads go to the floor?
If the reservoir is empty then either the front or rear brake pads need to be replaced or their is a leak somewhere in the brake system. Inspect for Brake System Leaks: Using a flashlight check the rear of the master cylinder where it bolts to the brake booster.
How do you replace disc brakes on a car?
On some rear disc brakes, the caliper pistons screw in, and require the disc brake pad spreader set to be seated properly. Take the caliper off the bungee cord and put it back on. VERY IMPORTANT – DO NOT OVERTIGHTEN the caliper bolts.