Are there any problems with Mercedes Benz W164?
Wear to the timing chain can also occur. When changing the filter, inspect the base of the housing that connects to the block for leaks. Also, inspect the oil cooler connections that are next to the oil filter for leaks. A lot of 2006-’07 model year Mercedes-Benz W164s came with M272 and 273 engines.
Why are the flaps on my Mercedes W164 not moving?
When the flaps can’t move due to damage to the actuators or the linkages, the driver may complain of poor idle, loss of power and a check engine light with a P2006 code and other codes that can include changes to the long-term fuel trim.
Where are the fuses on a Mercedes Benz W164?
Fuse locations on Mercedes-Benz M-Class W164 2006-2011. Main fuse box and relay box is located in the engine compartment. Rear, passenger side in the trunk. Inside the cabin. Passenger side of dash. Prefuse box in the engine compartment. Near the hood hinge, passenger side. Prefuse box by the battery.
Is there rust on my Mercedes Benz W164?
On older W164 SUVs in the salt belt states, rust is starting to eat away at the doors and wheel arches. Mercedes-Benz vehicles are not immune to rust and corrosion of the brake lines. The most common area for corrosion is above the fuel tank.
Wear to the timing chain can also occur. When changing the filter, inspect the base of the housing that connects to the block for leaks. Also, inspect the oil cooler connections that are next to the oil filter for leaks. A lot of 2006-’07 model year Mercedes-Benz W164s came with M272 and 273 engines.
Why is the compressor not working on my Mercedes W164?
If a reservoir is low or depleted, it will run the compressor while the engine is idling. If you’ve replaced the fuse and relay for the compressor and it now works, look at the current draw. Like all electric motors, when the electric motor starts, it draws about twice the amount of amperage to get the pump moving.
When the flaps can’t move due to damage to the actuators or the linkages, the driver may complain of poor idle, loss of power and a check engine light with a P2006 code and other codes that can include changes to the long-term fuel trim.
Why is the unlock button not working on my Mercedes?
Make sure it’s the button and not the antenna. If you get a message on the cluster’s MFD such as “key not detected” when you press the button, then it’s an antenna. If you get nothing, it’s the button.
Is the key fob on my SL500 not working?
My 2003 SL500 has Keyless Go (Key fob). The touch sensor on the drivers door was intermittent for about a month and has now stopped working. The passenger door touch sensor was working fine but has also stopped working. The doors unlock if I pull the handle gently.
What should I do if my Mercedes key fob is not working?
If you need a replacement battery note that Mercedes-Benz uses CR2025 battery type. Ensure you have new batteries in your key fob. Next, look carefully at your Mercedes-Benz key. When you press the button on your key you should see a small RED led light. The light should light up every time you press any of the buttons (Lock, Unlock, Panic, Trunk).
Why is the touch sensor on my Mercedes not working?
The passenger door touch sensor was working fine but has also stopped working. The doors unlock if I pull the handle gently. Any ideas on how I can sort this before what is certainly an expensive trip to the Merc workshop?
Can you read the fault code on a Mercedes Benz?
Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS
Is there a diagnostic scanner for Mercedes Benz?
Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships. Yes, it can do anything including programming of sensors and features. Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes.
What are the diagnostic codes for Mercedes Benz?
Mercedes-Benz Diagnostic Trouble Codes (DTC) for 1996+ models Powertrain P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent
What is fault code b1859 on Mercedes Benz?
There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.
Is the b1628 turn signal lamp in module e2e5 defective?
B1628 Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. B1858 Two-way radio signal. The progammed code is ok, but the programmable code is not synchronised. B2708 ?
What kind of transfer case does a W164 have?
The W164 has an optional low-range transfer case with locking differential in the center and rear for the ML550 and AMG ML53. On most models, the transfer case has its own module that controls the operation of the center differential and high- and low-range operation, as well as distribution of power under normal operation.
What kind of transmission does an AMG W164 have?
The AMG version of the W164 has the MCT transmission — essentially the 7G-Tronic automatic transmission without a torque converter. Instead of a torque converter, it uses a compact wet startup clutch to launch the car from a stop and also supports computer-controlled double-declutching.