Is the door lock actuator on a Mercedes C class broken?

If the door locks in your C-Class are bouncing up and down or are otherwise not functioning properly, the system’s actuator might be broken. This is a costly component to replace at the repair shop, but it is something you can do at home.

What kind of actuator does a Mercedes Grand Cherokee use?

G001 replaces the older G-219 ( (Usually found on Mercedes-Benz 3.0L Diesel) and G-277 actuators. There was a problem filtering reviews right now.

How much does it cost to replace door lock actuator?

Due to their frequent use, the springs in the door lock actuator mechanism wear out over time. This can result in the car’s locks malfunctioning; whereupon, they either don’t work at all or otherwise bounce up and down. It’s an expensive component to replace—with average parts and labor prices somewhere around $650.

Can a turbo actuator be installed on a 2007 sprinter?

Worked on my 2007 Sprinter van. Fixed my under boost code that I have been battling. Took me 30 minutes to install. Great replacement without having to buy a 3k turbo. Verified Purchase Early Reviewer Rewards ( What’s this?) Product was perfect replacement. Old actuator stripped gears. Bought this one and installed.

G001 replaces the older G-219 ( (Usually found on Mercedes-Benz 3.0L Diesel) and G-277 actuators. There was a problem filtering reviews right now.

When to replace the throttle possition sensor on a Mercedes Benz?

If you determine the throttle position sensor has failed on your Mercedes-Benz you will need to address this problem right away. In most cases, you will get code P0120 or P012x. Your options are to replace it with a new throttle position sensor.

Is there a problem with the Mercedes possition sensor?

Mercedes-Benz throttle body or throttle position sensor found on C-Class, E-Class, S-Class, CLK-Class, SLK-Class may fail causing idle issues, no idle or poor acceleration. Symptoms of defective Mercedes throttle body or throttle position sensor include: A common problem that you may notice is that the car drives fine under normal acceleration.

How do you remove a door lock actuator?

Carefully lever around the edge of the door trim, and lift it off. Pull up and forwards on the door trim to remove. Disconnect all hook linkage, and remove insulation in order to access actuator housing area. (Related Article: How to Remove Door Trim Panel – MBWorld.org) Remove the T30 Torx screws holding the actuator.

How do you remove the door handle on a Mercedes C class?

Once done, remove the handle’s blanking plate and unscrew the T20 Torx that holds the outer door handle. Now, in order to remove the handle, first remove small part of the handle release by removing the previous T20 Torx. Next, slide handle to the left to release from vehicle.

Where can I buy a 2004 Mercedes CLK Class?

2004 CLK-Class listings within 50 miles of your ZIP code. Get answers to buy with confidence. Save when you purchase multiple reports. Select from one or more dropdowns below, to find the right car for you.

Why is my driver’s side door lock not working?

Thanks to the good people here at Benzworld.org I was able to fix my driver’s side door lock without involving my mechanic or having to buy parts. This seems to be a huge issue with W202’s and something that many of you will also deal with. My driver’s side door lock stopped working.

Why does my drivers side window not work?

A smaller version of GM’s rebirth of the Hummer. Hard to start yesterday,drivers side window,power door locks wont work,either by buttons on both doors or on key fob.Other windows work! Replaced Battery checked door lock fuse,still no drivers side window or door locks. Answered! View the answer I have this problem too Is this a good question?

How does the power door lock work on a Chrysler 300C?

The driver side window/lock switch combines a power lock switch, a driver power window switch with an Auto-down feature, master switches for each passenger door power window, a power window lockout switch, a power mirror selector switch, and four power mirror adjustment switches in a single assembly.

Why does my driver side door lock not work?

The windows and the locks are on two separate circuits. The only part that these two have in common is the master switch. Of course it is also possible that the wiring harness between the driver side door and cowl is corroded and that some of the pins are to corroded or even broken off and do not make contact.

Where is the lock actuator on a car?

Each door in your vehicle has what is called a door lock actuator on it. A door lock actuator is mounted on the inside of a car door, and it contains a series of parts in it including an electric motor, gears, and cables that connect to lock on the door.

What to do if your door lock actuator is bad?

If you know that you have a bad door lock actuator in your car and you want to get it fixed, it should be easy tracking down someone to help you with it. Just about any ASE-certified mechanic should be able to pop your old door lock actuator out and put a new one into its place in no time.

Why is my car door lock not working?

If your car door lock actuator is not working properly, a common problem is that the plastic air reservoir (at the bottom of the actuator) is broken or cracked. Air leaks will cause the actuator to not be able to pull the door to the close position. This rebuilt kit is designed to fix the problem without changing the complete assembly. Loading…

How does a Mercedes Benz door lock work?

Mercedes-Benz vehicles such as E, C, S, ML, GL, R Class are designed to automatically lock the doors as soon as you start to drive. On those models, the door lock actuators may fail causing the door lock to bounce up and down several times.

Why are my door locks on my ML 500 not working?

Both of the door locks on the right side of my ML 500 are not working properly. They bounce up and down but do not lock. Here is a video of what they do:

What do I need to repair a Mercedes door lock?

2. You will need a torx driver with at least a 4 inch shaft to get to the torx screw for the door handle removal. 3. Buy a set of nylon trim and molding removal tools. It will help get the panels off without scratching the panels or the paint.

Both of the door locks on the right side of my ML 500 are not working properly. They bounce up and down but do not lock. Here is a video of what they do:

Navigation