What is the fault code for Mercedes Benz?
OK, as some of you probably know, i took it in for a diagnostic last week as it was cutting out when under heavy acceleration, and the fault was diagnosed as ‘loss of pressure at the fuel rail’.
What causes a Mercedes Benz to not start?
In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems
What does p0170 stand for in auto repair?
Dirty air filter, air filter housing or Mass Air Flow (MAF) sensor, or faulty MAF sensor are common causes for the P0170 code. The cost to diagnose the P0170 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
Which is the best OBD code reader for Mercedes Benz?
Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2. BlueDriver Scan Tool for iPhone and Android
What causes an OBD code of p0793?
A defective intermediate shaft speed sensor, or either the output or input speed sensor, is usually the cause of a P0793 trouble code. In addition to these causes, damaged or shorted wiring or connectors can also cause the storage of this code.
When is the p0793 Mercedes-Benz intermediate shaft speed sensor detected?
The P0793 Mercedes-Benz code is detected when the vehicle speed is more than the 31 mph and the park/neutral switch is OFF or rhe engine speed is less that 300 RPM. This sensor detects the rotation speed of the counter gear.
What is the OBD code on a Mercedes?
What about the obd code? The P0793 Mercedes-Benz code is detected when the vehicle speed is more than the 31 mph and the park/neutral switch is OFF or rhe engine speed is less that 300 RPM. This sensor detects the rotation speed of the counter gear.
OK, as some of you probably know, i took it in for a diagnostic last week as it was cutting out when under heavy acceleration, and the fault was diagnosed as ‘loss of pressure at the fuel rail’.
P1612 Voltage terminal 15 Analysis circuit is faulty. P1615 N3/9 (CDI control module) Supply voltage Signal is too large. P1615 N3/9 (CDI control module) Supply voltage Signal is too small. P1617 EEPROM or incorrectly coded AT has been coded as MT. P1617 EEPROM or incorrectly coded CAN was interrupted during coding.
Is there a problem with my Mercedes C320?
We have a 2004 Mercedes C320 with a no crank problem. We jumped the starter relay and the starter cranks. We’ve had several of this model lately … read more
What are the Mercedes OBD-II Diagnostic Trouble Codes?
This is the list of Mercedes specific OBD-II Diagnostic Trouble Codes (DTC’s) that are used by Mercedes to diagnose the vehicle problems. This codes are presented for information only. You can always refer to the list of Standard or generic OBD-II DTC. P1105 Atmospheric pressure sensor Readout too large.
Are there any problems with the Mercedes P2000?
P2000 Component N15/3 (ETC control module) is faulty. P2000 Component N15/3 (ETC control module) is faulty. P2000 N3/9 (controller CDI) hardware identification error. P2000 N3/9 (controller CDI) software ‘integration check’ error.
What’s the fault code on a Mercedes C320?
Drove it to a mechanic across the street from where this happened, and they can’t pull MB codes well, but it is firing a P203B, which the mechanic said was somehow related to the MAF. I did a search for P203B on the forum and it apparently refers to a cylinder issue (at least in vans).
Can you erase a fault code on a Mercedes Benz?
Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships.
Why is my 2001 C320 giving me an ESP warning?
So I have a 2001 C320 that I bought at auction today. It was giving me an ESP warning on the dash, then it lost all power and wouldn’t pass 7 mph or so. Drove it to a mechanic across the street from where this happened, and they can’t pull MB codes well, but it is firing a P203B, which the mechanic said was somehow related to the MAF.
What are all the codes on a Mercedes Benz?
Use an advanced OBD-II code reader to read and erase Engine CEL, Transmission, ETS, ABS, Airbag and other systems. There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner.