How to replace the hood latch on a Mercedes Benz?

How to replace the hood latch mechanism on a Mercedes-Benz. Replacing the hood release mechanism is very easy once you get the hood to open. The hood latch is held in place with two bolt. You will need a 10 mm open ended wrench or a socket. Remove the two bolts. You should be able to pull up the latch.

What happens when you open the hood on a Mercedes Benz?

Normally you will go to open the hood and you should hear a pop and the hood lifting up an inch or two. Then you manually have to release the hood. Before we start troubleshooting it is important that we understand how a hood latch works. The hood latch has a two-step lock.

What should I do if my Hood cable broke?

If your cable is broken you have a couple of options on how to open the hood. First you need to see if you can use a set of pliers to pull on the broken cable. That of course depends on where the cable broke. If the cable broke by the hood release under the dash, you may be able to use a set of pliers to pull on the cable.

Why does my car hood latch not open?

The latch can get sticky due to dust, dirt and rust. The cable can also get sticky. There could be several reasons why the hood will not open. In most cases the problem is the hood release mechanism or the hood latch. That’s why it is important to lubricate the hood latch at least once a year.

What to do if your hood latch is broken?

SOLUTION FOUND! Without replies and an extensive web search producing nothing, I went at it myself. Simply – remove the two 10mm bolts directly behind the grille holding the latch mechanism together. Caution: The airbag sensor is protected by a metal shroud which is also connected via these two bolts.

How do you open the hood on a Mercedes Benz?

Now try to lift up the hood, while your friend is holding the hood release under the dash in the open position. Depending on the Mercedes-Benz model that you have, you may be able to access the hood release through the grille. Try pushing the release lever using a long screwdriver and open the hood.

Why is the hood of my Mercedes Benz closed?

Your Mercedes-Benz may also show a open hood / close hood error message on your instrument cluster but the hood is closed. This is most typically caused by the hood latch micro switch. Part of the hood latch is a small on/off switch known as the microswitch this could be defective.

Why is the liftgate not working on my Mercedes ML350?

If you manually close the tailgate, will the latch lock and pull the tailgate tighter? A bit of history. Shortly after I bought the vehicle, the liftgate stopped working. When I would push the remote lift button, it would disengage the latch but not lift. Then the latch would re-engage and shut tight.

How do you close the hood on a Mercedes Benz ML350?

Sometimes, especially on older ML350s, you may have difficulty getting your hood to latch when you close it. In this case, the interior release lever on your 2007 Mercedes-Benz ML350 is probably stuck in the “open” position – push the release lever back and forth several times and then try to close your hood.

How does the hood latch on a Mercedes Benz work?

Before we start troubleshooting it is important that we understand how a hood latch works. The hood latch has a two-step lock. One function is to completely lock the hood in closed position and the other function is to lock the hood from opening when you drive down the highway.

Why does the hood on my Mercedes not pop up?

Sometimes, the hood on Mercedes-Benzs gets stuck and won’t pop up after the interior latch is released. If this occurs on your ML350, simply pull up on the hood and it should pop up for you to release the second latch. Sometimes, especially on older ML350s, you may have difficulty getting your hood to latch when you close it.

How to find Mercedes body and trim parts?

Mercedes Parts > Body & Trim Filter Parts By Model Range MakeMercedesSmartModel Year Apply Filter Clear Filter Saab VIN Look Up To accurately identify manufacturer specified vehicle model year (which can frequently be different to year of registration), please enter your 17 digit (vehicle identification number) VIN or Chassis number below.

What kind of clips do you use on a Mercedes?

We have Mercedes-Benz door panel retaining clips for the door cards and Mercedes door trim clips for the surrounding dress-up pieces. Fixing up the exterior? Get some of our Mercedes plastic rivets to get a good fit for fender liners, grilles and more.

How can I get my Mercedes Benz hood to release?

The second method to get the hood to release is to access the hood latch release from underneath. This is more tricky and a bit more difficult. Before you do that use a flashlight to check if the hood cable is in the right slot. Very often the cable falls off the slot and no longer can release the hood.

Why is the hood of my Mercedes Benz stuck?

At this point, you should hear the hood pop. Second, is released by pressing on the hood release tab under the hood. If your hood doesn’t open or close properly it can be because of dirty or rust in the hood latch mechanism or rust in the release cable. The good news is that typically it is not very hard to fix a hood problem.

How do you remove the hood release cable?

Remove the hood release cable at the hood latch using the needle-nose pliers. Grab the round ball on the end of the cable in the latch, and lift it up and out of the retainer spring. Remove the screw holding the cable to the latch. Pull the cable from behind the headlight and guide it with your hand until it is out past the headlight.

How do you remove the hood of a car?

Remove the hood release cable at the hood latch using the needle-nose pliers. Grab the round ball on the end of the cable in the latch, and lift it up and out of the retainer spring.

Is there a service campaign for Mercedes Benz E430?

Mercedes-Benz USA issued Service Campaign #2005-02003 which directed the inspection of Mercedes-Benz E430 parts and required replacement at no cost. Replacement of the faulty part with the updated part was made the permanent solution to this problem. Most E-classes end up with a sub 35 mile-per-hour clicking or rattling sound from the front end.

Who was the designer of the Mercedes E430?

The Mercedes-Benz E430 was known for its classic W210 E-class appearance which was designed by Steve Mattin under design chief Bruno Sacco, heralding a brand-new design idiom for the Mercedes face-a characteristic twin-headlamp design. Although it was a car of many first innovations, it was hardly what you’d call perfect.

Why is the hood of my Mercedes Benz not opening?

Your hood may not open because of damage to the latch or also due to bend hook on the hood itself. Make sure the hook on the hood is not damaged or bent. On certain Mercedes-Benz models a spring is used to allow the hood to pop-up. There is either one spring at the center of the hood or two springs on the sides.

What to do if your Mercedes Benz hood is stuck?

If this happens to you, you may want to try spraying some lithium grease at the hood release. This may allow to hood latch to unstick and start operating normally. Also try having a friend help by pulling and keep open the hood release under the dash while you try to jiggle the hood up and down to open it.

Is the rollbar light on in my 1998 Mercedes SL 500?

1998 Mercedes sl 500 my rollbar light &top light on but top working & rollbar work when open and close top That all happen after battery dead and I try to start T.Y. 30 people found this helpful. schlieve I seem to have the same issue.

Why is the top of my Mercedes SL not working?

On later model SL’s – both switches need to be depressed for the top to operate. This is usually accomplished by having the cargo cover in place and closed. If it is open – the computer thinks the trunk doesn’t have room for the top so it will not operate.

Why is the hood latch on my Mercedes stuck?

Your Mercedes-Benz hood latch may get stuck or sticks due to lack of lubrication. That is why it is important to keep the dirt off the hood latch and the hood release cable. The latch can get sticky due to dust, dirt and rust. The cable can also get sticky. There could be several reasons why the hood will not open.

Why is the hood lock on my 300SD not working?

I think the lock is pulling the hood to one side . If you loosen the screws just a litlle and you try to adjust it carefully with a hammer a litllebit I think your problems are over. My 1982 300SD (126) is suffering from a balky hood latch.

How do you open the hood on a 300SD?

The 300SD with the 126 body has two release levers, one on each side of the grille. Press both towards the grill to release. The 300SD has a unique hood opening latch that is not shared by any other M-B vehicle as far as I know except maybe other w126s from that generation.

What to do if your car hood is stuck?

It is possible that one of the hood latches may open but the other may not. If this happens to you, you may want to try spraying some lithium grease at the hood release. This may allow to hood latch to unstick and start operating normally.

What do you need to know about Mercedes wiring diagrams?

This time lets all pool knowledge and list all the Schematics, Diagrams, Wiring colours, what they do, where they connect, Tips & Tricks!

Are there any Mercedes Benz parts that fit?

Genuine Mercedes-Benz Parts fit your vehicle like no others can. They’re engineered specifically to function with their fellow parts and systems, and they’re constructed from the finest materials available. They’re also subjected to rigorous testing, which means each part comes fully certified.

Navigation