What is the SBC brake failure error code c249f?
SBC Brake Failure Error CODE C249F Fault 1 Operating time of Component of A7/3 is exceeded. 2 Complete failure of the SBC/Electro-Hydraulic Brake System Hydraulic Pump 3 In a few cases a defective brake switch could cause the same error message. You can buy one on Amazon see here, for less… More …
What is the SBC brake defective stop code?
SBC Brake Failure Error CODE C249F Fault – MB Medic Brake defective Stop Vehicle! SBC Brake Failure Error CODE C249F Fault If you have a Mercedes Benz with Sensotronic Brakes also known as brake by wire you may have been greeted with the “Brakes Defective Stop Vehicle” error message in your instrument cluster.
Where is the switch on Mercedes Benz SBC?
The switch is located right above the brake pedal and can easily be replaced by anyone. We belive that Mercedes Benz set a cycle limit to the SBC Hydraulic pump based on their testing and research. The SBC module counts breaking cycles, after exciting the value of approx 300000 , an error message occurs. Some of the errors reported are:
What is the SBC error code on a Mercedes?
This error is common issue on Mercedes E Class W211, SL R230, CLS Class with SBC Error CODE C249F. After so many operation cycles the SBC looses efficiency or can completely fail while driving. So that you don’t get a failure while driving they want you to replace the SBC Hydraulic Unit before it fails catastrophically.
SBC Brake Failure Error CODE C249F Fault 1 Operating time of Component of A7/3 is exceeded. 2 Complete failure of the SBC/Electro-Hydraulic Brake System Hydraulic Pump 3 In a few cases a defective brake switch could cause the same error message. You can buy one on Amazon see here, for less… More
SBC Brake Failure Error CODE C249F Fault – MB Medic Brake defective Stop Vehicle! SBC Brake Failure Error CODE C249F Fault If you have a Mercedes Benz with Sensotronic Brakes also known as brake by wire you may have been greeted with the “Brakes Defective Stop Vehicle” error message in your instrument cluster.
How to reset the W211 SBC fault code c249f?
Carefully remove the SBC control unit , there is a special way to remove the SBC, you will have to de-activate the pump first. There is also a very special procedure to refit. NOTE: The SBC unit has to be disabled before removing. Just use a special Star diagnostic diagnostic tool (e.g. SD C4) to reset the fault
This error is common issue on Mercedes E Class W211, SL R230, CLS Class with SBC Error CODE C249F. After so many operation cycles the SBC looses efficiency or can completely fail while driving. So that you don’t get a failure while driving they want you to replace the SBC Hydraulic Unit before it fails catastrophically.
Do you have to use diagnostic scanner to replace brake pads?
With these kinds of brake calipers, you do not have to use a diagnostic scanner to replace the brake pads, you can push in the pistons with a tool like this on Amazon on the link down below, but always make sure by checking your repair manual before replacement.
When do you know your brake pads need to be replaced?
If you notice that your brake pads are worn down, you should replace them as soon as you can. Listen to your brakes as you come to a stop. Many brakes have squealers installed on them which will indicate when your brake pads start to wear thin. These squealers will let out a loud, high-pitched sound when your brake pads get too thin.
What causes error code c249f or the brakes defective stop?
For Mercedes-Benz, a cycle limit has been set for its SBC hydraulic pump. After the SBC module count reaches approximately 300,000, any of the following error below gets displayed on the instrument cluster: 2. The SBC/Electro-Hydraulic Brake System Hydraulic Pump was completely damaged.
What causes error code c26de or the brakes defective stop?
• C26DE/ C26BB Hydraulic Fault – Both error codes are caused by a malfunction in the car’s pressure supply. For error code proper evaluation and other issues requiring Mercedes Benz repair, call Laguna Niguel Auto Center at (949) 582-2191.
What does N17 mean on a brake pad?
There is an X or WX compliance marking as well that indicates an exemption from the regulation. In the recommended edge code structure, the numbers that follow the A, B or N are for dating purposes. So, N17 would mean an “N” formulation, manufactured in 2017.
What is the SBC error code for Mercedes CLS?
This error is common issue on Mercedes E Class W211, SL R230, CLS Class with SBC Error CODE C249F. After so many operation cycles the SBC looses efficiency or can completely fail while driving.
Can a defective brake switch cause an error message?
In a few cases a defective brake switch could cause the same error message. You can buy one on Amazon see here, for less than $20. The switch is located right above the brake pedal and can easily be replaced by anyone. We belive that Mercedes Benz set a cycle limit to the SBC Hydraulic pump based on their testing and research.
This error is common issue on Mercedes E Class W211, SL R230, CLS Class with SBC Error CODE C249F. After so many operation cycles the SBC looses efficiency or can completely fail while driving.
What is the SBC code for a Mercedes W211?
Mercedes E Class W211/R230 SBC Repair CODE C249F – Sensotronic Brake Control (SBC) If you own a Mercedes E Class W211 or SL R320 and have a brake error, then you must replace the SBC unit which can be very expensive from the dealer. Please note, we can only repair the fault electronically and not the physical hydraulic.
Why is my SBC pump not working on my Mercedes?
Your SBC pump is defective and you loose all the braking or have reduced braking power. The SBC pump which creates pressure and applies that pressure to the brakes when you push the brake pedal is not working properly. This error is common issue on Mercedes E Class W211, SL R230, CLS Class with SBC Error CODE C249F.