Why is the OBDII port on my Mercedes not working?
I received that cable yesterday and took the car to an Advanced Auto store this morning and they tried their basic scanner with this converter cable on the 38 pin socked and still had no communication or power, so I still can’t read my codes.
Can a check engine light show an OBD2 code?
When the system identifies an issue, it turns on the check engine light and provides real-time data in addition to a standardized series of Diagnostic Trouble Codes (or DTCs). With a code reader or scanner, you can access one or more OBD2 codes that indicate the issues.
Why is my PCM not connecting to the OBD2 port?
If no ground the circuit is broken somewhere between the OBD2 connector and the PCM If the ground is good then it is either a bad connection on pin 2 back to the PCM or a Bad PCM itself, which I suspect is the problem. Note that the OBD2 port is fused.
What should I do if my OBD2 is not linking?
Autel AL519 Autel Autolink al319 Launch Scan Tool Launch x431 Launch crp129 Launch crp123 Innova Scanner Innova 3030 Innova 3040 Foxwell Scanner Foxwell NT301 FOXWELL NT510 Foxwell NT624 FOXWELL NT630 Actron Scanner Actron CP9690 Actron CP9680 Actron CP9670 Other Bluedriver OBD2 Bluetooth Scanner Konnwei KW808 Bafx 34t5
Where is the OBD2 port in my Mercedes M / ML class-164?
OBD connector location for Mercedes M Class (ML) – W164 (2005 – 2011) You will find below several pictures which will help you find your OBD connector in your car. The OBD port is located above the pedals. Go to the OBD2. scanner for MERCEDES. Remove the cover, the connector is under it.
I received that cable yesterday and took the car to an Advanced Auto store this morning and they tried their basic scanner with this converter cable on the 38 pin socked and still had no communication or power, so I still can’t read my codes.
Where is my OBD2 port in my car?
Since the implementation of the OBD standard, each vehicle has a standard 16-pin connector, as described on our OBD presentation page. The norm states that the port must be located inside the vehicle passenger compartment.
Autel AL519 Autel Autolink al319 Launch Scan Tool Launch x431 Launch crp129 Launch crp123 Innova Scanner Innova 3030 Innova 3040 Foxwell Scanner Foxwell NT301 FOXWELL NT510 Foxwell NT624 FOXWELL NT630 Actron Scanner Actron CP9690 Actron CP9680 Actron CP9670 Other Bluedriver OBD2 Bluetooth Scanner Konnwei KW808 Bafx 34t5
When does the engine stall in a Mercedes?
There are never any notifications on the dash or any signs of it beginning to fail. This typically happens when I’m slowing down at an intersection or just driving slower in traffic.
Why is my OBDII reader not working in my car?
He even took an OBDII reader and plugged it in to the port in my car to show me that the port is not working, the machine was not even powering up at all.
Why is the ECU not working on my Mercedes Benz?
He specified that he just could not make a connection to the ECU at ALL; he took the time to explain that a lot of times when cars come to his shop the machine is not able to read the readiness portion for the cars to pass smog, something that can be fixed by driving the car around for several hours, but that was not the case with my car.
What should I do if my Mercedes Benz won’t start?
Start the car and you should be able to get around 60 psi. When the engine is running and when you turn off the engine the pressure should stay steady. Always perform this test on a cold engine. Next, make sure that the fuel injector connections are secure and not loose. Check the fuel pump and the fuel pump relay.
Why does my Mercedes not start when I charge the battery?
This Mercedes-Benz is not starting because of a low battery. In this case, what you need to do is trickle charge your battery using any of these 12 volt battery trickle chargers. If you need help read this article on How to charge a Mercedes-Benz the right way. Mercedes won’t start, and it’s not the battery.
What are the problems with a Mercedes Benz?
Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More
When does a Freightliner classic no data link alert come on?
I have a 2005 Freightliner Classic w/14L Detroit 60 Series, 10 spd Ultrashift. I get a “No Data Link” alert after the truck is washed even when the hood is kept closed. When I get the alert the Tach, speedo, oil press, coolant temp, and voltage gages all are dead.
He specified that he just could not make a connection to the ECU at ALL; he took the time to explain that a lot of times when cars come to his shop the machine is not able to read the readiness portion for the cars to pass smog, something that can be fixed by driving the car around for several hours, but that was not the case with my car.
When do I get ” No data link ” alert?
I get a “No Data Link” alert after the truck is washed even when the hood is kept closed. When I get the alert the Tach, speedo, oil press, coolant temp, and voltage gages all are dead. After sitting 20 minutes or so it all goes back to normal. Fortunately when this happens it still starts and shifts.