What is the fault code for the Vito oil sensor?
Have fault codes P1482 (glow) P2006 (mainifold air control) P1470 Boost Pressure P1188 ( Piston cutoff solenoid) and P1192 oil sensor but the last 2 only show up if I plug in Fuse 23. (ecu feed ) Engine fan then comes on an van will rev irratic to 1500rpm up and down like a misfire. Without fuse 23 it runs ok but in limp mode.
Where is the coolant temperature sensor on a Mercedes Vito?
The coolant temperature sensor is located on the front of the thermostat. This is on the left hand side of the engine bay tucked in behind the oil filter and near the alternator. Easiest access is through the front – pop the grill off and you can get your arm in.
Is the CCS sensor on the Vito too sensitive?
If you put the correct amount in ccs according to the manual it would be fine and the level would be bang smack in the middle of the full and low marks . So you have to ask the question is the sensor on the vito too sensitive or is the dipstick just slightly inaccurate did someone get it wrong and not allow for the expansion of oil.
Where is the oil leak on a 272 / 273 Mercedes?
272/273 Engines: The most likely rear engine leaks include the oil separator and the cam plugs ( 30mm and 65mm ). The oil separator is held onto the back of bank 1 (passenger side) with either 4 torx bolts or 4 external torx bolts. Remove the oil separator, replace, and clean the oil residue from the engine.
Where is the oil leak on my Vito?
The oil pools and runs down the side of the alternator. I have a 113 ’99 petrol Vito, get a bright torch and look from under neath to the rear of the block, sounds like from either the oil pump or up towards the timing chain tensioner (back of the block) or from around the oil pump.
How much oil goes into a Mercedes Vito van?
Engineer Bachelor’s Degree 807 satisfied customers How much liters of oil goes into automatic transmission of how much liters of oil goes into automatic transmission of vito 112 cdi 3003 … read more Matt Engineer Bachelor’s Degree 807 satisfied customers vito: ***** ***** can you tell me where can I find the engine
Have fault codes P1482 (glow) P2006 (mainifold air control) P1470 Boost Pressure P1188 ( Piston cutoff solenoid) and P1192 oil sensor but the last 2 only show up if I plug in Fuse 23. (ecu feed ) Engine fan then comes on an van will rev irratic to 1500rpm up and down like a misfire. Without fuse 23 it runs ok but in limp mode.
How do I remove a radiator from my Mercedes Vito van?
How do I remove a radiator from my mercedes vito van 2005 model 109cdi? How do I remove a radiator from my mercedes vito van 2005 model 109cdi? – Answered by a verified Mercedes Mechanic We use cookies to give you the best possible experience on our website.
What kind of engine does a Mercedes Vito have?
Vito nameplate stayed but the Viano was replaced with Valente. They also brought back Front Wheel Drive versions, but with only one engine. The 111CDI 1.6 Litre Turbo Diesel engine; an engine made by Renault. At Grant Walker Parts in Melbourne, we stock a large range of Mercedes-Benz spare parts that can be shipped Australia wide.
Where can I get Mercedes Benz Vito parts?
At Grant Walker Parts in Melbourne, we stock a large range of Mercedes-Benz spare parts that can be shipped Australia wide. Have a question or need some advice? The W447 is the third generation of the “V-Class”. Vito nameplate stayed but the Viano was replaced with Valente.
Why does my Vito CDI 110 2000 shut off?
Hi My Vito CDI 110 2000 has Shut off Fault Code, Boost Pressure Code. 7.5a ECU Fuse causes grey smoke rough running when inserted. Merc Star Can not communicate with the CDI. Van starts and runs ok without the 7.5a fuse but in limp mode. Help.
What makes a union ball valve Viton or EPDM?
The material can dictate the temperature tolerance of a seal. It can also give the seal certain chemical resistances, with some types of rubber being compatible with difference fluids. Two common materials for true union ball valves are Viton and EPDM.
How to set up the cams on a Vito?
ensure the timing adjuster is against its stop in the direction of camshaft rotation. you may need to try the cams in a couple of positions on the chains to get this right – normally the gears should be marked in line with the chain before removal. ensure the slack is on the tensioner side, start with the inlet camshaft 1st, then the exhaustcam.
When do you use Viton seal for fuel?
Viton is great for use with fuel and other corrosive materials, but that extreme durability is unnecessary when dealing with something harmless like water. If you want to ensure maximum durability under stressful conditions, Viton is the ideal choice.
What is the difference between Viton and EPDM seals?
Two common materials for true union ball valves are Viton and EPDM. Viton (shown in image on the right) is a synthetic rubber with a high chemical and temperature resistance. EPDM, which stands for ethylene propylene diene monomer, has its own set of properties that make it an extremely popular O-ring…