How much does a Mercedes Benz control arm cost?

The bushings range from about $40-$50 a side. A good control arm is about $300 a side, and very well might be more if you buy an official MB control arm. You can get cheap control arms for about $150 a side, but they are a pretty critical part of your suspension.

Which is Mercedes Benz engine control unit to replace?

Some of the most popular ecm’s we sell are 2000, 2002, 2003 and 2004 C class and 2005 E320 models. The 2007 S550 ecu is also a popular item. Part number A2731535079 and A2731535679 are both popular S550 replacements. Call us if you have any questions.

Do you need to replace lower control arm or bushing?

I can tell you that no matter who you go to you probably don’t want to replace the entire control arms unless they are bad. With your car being a 1993 you probably do need to change your bushings. While you have the control arm out you should probably go ahead and change your ball joints as well. The ball joints are about $30-$40 a side.

When to replace the ECM in a Mercedes Benz?

Where can I get a Mercedes engine control unit rebuilt?

Order a Mercedes engine control unit from a certified rebuilder at a discounted price. We offer complete ecm repair and rebuild services for all makes and models including Jaguar, BMW, Lexus and Mercedes Benz.

Can a person steal a Mercedes Benz ECM?

The only way someone can steal your car is with your transponder key or a tow truck. So if you have a bad ecm that requires replacement then we will have to program the new ecm to match all the data of your old ecm.

Which is the best Mercedes Sam control module?

Go to top 1 C- Class SAM Control Module C230 C240 C320 W203 W204 (eBay link) 2 E-Class SAM Control Module E320 E350 E500 W210 W211 W212 (eBay link) 3 S-Class SAM Control Module S320 S430 S350 S500 S600 CL500 W220 W221 (eBay link) 4 ML-Class SAM Control Module ML320 ML350 (eBay link) More …

How much does it cost to repair a Mercedes C280?

Over 600,000 car repair estimates provided since 2012. Just fill out the form and get your estimate immediately. The annual cost estimate to maintain a Mercedes-Benz C280 is approximately $598**, depending on your service provider.

What causes a Mercedes signal acquisition module to fail?

Typically this is caused because repair is performed in near the SAM control unit. If the SAM modules are not closed and sealed, properly they will eventually corrode. If a SAM module fails due to corrosion, at first you may notice that electrical problems are intermittent. Excessive current draw – SAM control units don’t fail often.

How do you replace a lower control arm?

To start the ball joint must be released which can be done using a large wrench 20mm to 24mm or socket and loosening the ball joint nut after the cotter pin has been removed. Then by using a hammer strike the spindle or control arm bulkhead to “shock” the taper fit loose.

How do you change the bushing on a control arm?

Place the new bushing into the lower control arm while observing the marks you made from the old bushing. Do not apply lubrication to the bushing case because it will allow the bushing to walk its way out of the arm while in use. Align the press and slowly force the new bushing into place.

What to use to tighten lower control arm bolts?

A universal socket and extension can really help when tightening the control arm bolts. Tighten the lower ball joint castle nut while aligning the cotter pin holes. Once the nut is tight insert the cotter pin. This pin is used to keep the nut in place as a safety precaution.

Is it good to replace your control arm and ball joint?

The reason it’s good to replace your control arm and ball joint is because it has a rubber bushing inside of it that can wear out over time causing your car’s suspension to feel sloppy. With a few simple tools and tricks you’ll be able to swap out your control arms and ball joints like a pro and your car will feel brand new again!

Navigation