What is the Mercedes P2004 check engine code?
Check Engine Mercedes P2004 Code A common failure point for Mercedes-Benz cars equipped with the M272 (350) and M273 (550) engines is the intake manifold air flap lever. When this component fails your Mercedes-Benz will turn on the check engine light triggering any the following codes: P2004 – Intake Manifold Runner Control Stuck Open Bank 1
When is the p0410 Mercedes-Benz code detected?
Most auto repairs shops charge between $75 and $150 per hour. When is the P0410 MERCEDES-BENZ code detected? The secondary air injection system does not detect the presence of air in the exhaust when introduced by the secondary air injection system. An air pump is used on the vehicle to lower tail pipe emissions on start-up.
What are the fault codes for a Mercedes Benz?
P0216 Injection Timing Control Circuit Malfunction P0217 Engine Overtemp Condition P0218 Transmission Over Temperature Condition P0219 Engine Overspeed Condition P0220 Throttle/Petal Position Sensor/Switch B Circuit Malfunction
Where is the air flap on a Mercedes p2005?
P2005 – Intake Manifold Runner Control Stuck Open Bank 2 To fix this problem you will need to replace the intake manifold air flap lever using Repair Kit 2721402401. This part is located by the intake manifold.
Most auto repairs shops charge between $75 and $150 per hour. When is the P0410 MERCEDES-BENZ code detected? The secondary air injection system does not detect the presence of air in the exhaust when introduced by the secondary air injection system. An air pump is used on the vehicle to lower tail pipe emissions on start-up.
What does the Mercedes Benz air pump code mean?
The P0410 Mercedes code definition:the emissions system. The AIR pump puts air to the exhaust to lower emissions. It takes in outside air and pumps it through two one-way check valves into each bank of the exhaust.
P0216 Injection Timing Control Circuit Malfunction P0217 Engine Overtemp Condition P0218 Transmission Over Temperature Condition P0219 Engine Overspeed Condition P0220 Throttle/Petal Position Sensor/Switch B Circuit Malfunction
Why does my Mercedes have an OBD code?
About 90% of the time that this code is set, the one-way check valves have worn out or failed and allow water (which occurs naturally in the exhaust) back into the pump. In any cold climate, especially in climates with higher humidity, this water may be more excessive.
What is the SBC error code on a Mercedes?
This error is common issue on Mercedes E Class W211, SL R230, CLS Class with SBC Error CODE C249F. After so many operation cycles the SBC looses efficiency or can completely fail while driving. So that you don’t get a failure while driving they want you to replace the SBC Hydraulic Unit before it fails catastrophically.
How to check Mercedes Benz air conditioner trouble codes?
Push the left “AUTO” button to scroll forward and right auto button to scroll back. Depress right AUTO switch repeatedly. Note trouble codes Purchase a larger refill can of 134a with a gauge on it so you can read the low side pressure – helps as a guide to filling the system to the correct level.
How to check the history of a Mercedes Benz?
Find all the latest facts, figures and Mercedes-Benz specs based on year, make and model. Mercedes-Benz vehicle history report may contain the following information: title problems, prior damages, unsafe salvage rebuilds, odometer mileage, theft, past sales.
What causes the p0025 OBD-II trouble code?
P0025 is the OBD-II generic code indicating the Engine Control Module (ECM) has determined that the exhaust variable camshaft timing for bank 2 is more retarded than what the ECM has commanded it be. This over retarded timing condition could be during the advancing or retarding phase of the exhaust camshaft timing. What causes the P0025 code?
What to do if your check engine light says p0022?
Check to see if there are any other codes along with P0022 and clear your Check Engine Light with FIXD. Check the engine oil level and condition. If it’s low, adjust to spec and test drive to see if the concern is resolved. If it’s dirty, change the oil and filter and test drive to see if the concern is resolved.
What does the p0012 code on an ECM mean?
The camshaft (s) is (are) adjusted by the ECM through the use of an oil control valve (s) (OCV) also called variable valve timing control solenoid valves. The P0012 code is set when the ECM detects the camshaft timing for the intake camshaft on bank 1 is more retarded than what it has been set to be. What Are The Symptoms Of Code P0012?
Check to see if there are any other codes along with P0022 and clear your Check Engine Light with FIXD. Check the engine oil level and condition. If it’s low, adjust to spec and test drive to see if the concern is resolved. If it’s dirty, change the oil and filter and test drive to see if the concern is resolved.
P0025 is the OBD-II generic code indicating the Engine Control Module (ECM) has determined that the exhaust variable camshaft timing for bank 2 is more retarded than what the ECM has commanded it be. This over retarded timing condition could be during the advancing or retarding phase of the exhaust camshaft timing. What causes the P0025 code?
The camshaft (s) is (are) adjusted by the ECM through the use of an oil control valve (s) (OCV) also called variable valve timing control solenoid valves. The P0012 code is set when the ECM detects the camshaft timing for the intake camshaft on bank 1 is more retarded than what it has been set to be. What Are The Symptoms Of Code P0012?
What is the trouble code for camshaft position B?
P0025 is a diagnostic trouble code (DTC) for “Camshaft Position B – Timing Over-Retarded (Bank 2)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation. Our certified mobile mechanics can come to your home or office to perform the Check Engine Light diagnostic.
What does the Mercedes Benz p0101 error code mean?
Ever started up your Mercedes and wondered what the P0101 error code means? If the malfunction indicator light (MIL) appears on your Mercedes Benz dashboard, this indicates the car’s on-board diagnostics sensor (OBD-II/OBD 2) has identified a problem regarding the mass air flow sensor (MAF Sensor). What is the Mass Air flow (MAF) sensor?
What causes a Mercedes Benz MAF error code?
The most common causes of the P0101 error code include a dirty or clogged air filter, a cracked or damaged air intake, or even the MAF sensor itself being contaminated or damaged.
How long does it take to remove intake manifold from Mercedes P2004?
Take several few pictures before you start disconnecting wires. This is the most time-consuming process and will take one to two hours. Once the intake manifold is removed from the engine cover the intakes with tape to avoid debris, dirt and tools falling into the cylinders.
Can you erase a fault code on a Mercedes Benz?
Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships.
What are all the codes on a Mercedes Benz?
Use an advanced OBD-II code reader to read and erase Engine CEL, Transmission, ETS, ABS, Airbag and other systems. There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner.
How many control units does a Mercedes Benz have?
There are also codes for other control units such as transmission, ABS, SRS, ESP, 4ETS, airbag, A/C. Mercedes-Benz can have up to 47 control units. You can NOT diagnose them with a simple OBD-2 scanner. To read these systems and their fault codes or erase them from your Mercedes-Benz you need more advanced OBD-II scanners.
How much does it cost to repair a P2004 Mercedes Benz?
(P2004) The cost to diagnose the P2004 MERCEDES-BENZ code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
What to do if your Mercedes P2004 manifold gets stuck?
Place some grease on the ball studs and then press the connecting rod until it locks in the ball studs. Once the vacuum actuator, connecting rod and manifold lever are connected test them by moving the manifold flaps. Ensure that there is no restriction that can cause the manifold flaps to get stuck.
Check Engine Mercedes P2004 Code A common failure point for Mercedes-Benz cars equipped with the M272 (350) and M273 (550) engines is the intake manifold air flap lever. When this component fails your Mercedes-Benz will turn on the check engine light triggering any the following codes: P2004 – Intake Manifold Runner Control Stuck Open Bank 1
(P2004) The cost to diagnose the P2004 MERCEDES-BENZ code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.
Place some grease on the ball studs and then press the connecting rod until it locks in the ball studs. Once the vacuum actuator, connecting rod and manifold lever are connected test them by moving the manifold flaps. Ensure that there is no restriction that can cause the manifold flaps to get stuck.
P2005 – Intake Manifold Runner Control Stuck Open Bank 2 To fix this problem you will need to replace the intake manifold air flap lever using Repair Kit 2721402401. This part is located by the intake manifold.
What does P2004 stand for in OBD code?
Code P2004 stands for Intake Manifold Runner Control Stuck Open Bank 1. The intake manifold directs air into the engine via a series of runners.
What causes an intake manifold code of P2004?
Code P2004 is typically caused by one of the following: A failed IMRC actuator A problem with the intake manifold or linkage Wiring issues
Code P2004 stands for Intake Manifold Runner Control Stuck Open Bank 1. The intake manifold directs air into the engine via a series of runners.
Code P2004 is typically caused by one of the following: A failed IMRC actuator A problem with the intake manifold or linkage Wiring issues
How long does it take to remove vacuum actuator from Mercedes P2004?
This is the most time-consuming process and will take one to two hours. Once the intake manifold is removed from the engine cover the intakes with tape to avoid debris, dirt and tools falling into the cylinders. Remove the vacuum actuator rod by pushing it out of the lever using a flat screwdriver.
Why is the air flap on my Mercedes P2004 breaking?
The flap may break due to wear or because of excessive carbon built up near the intake valves. Over time the plastic becomes brittle and eventually fails. Once the lever breaks the pull rod disconnects from the manifold air flap lever. The part is the same design for the M272 V6 and M273 V8 engines.
When was the Mercedes CLK 350 last serviced?
No accident or damage reported to CARFAX… 1st owner purchased on 06/08/09 and owne… Last serviced at 101,973 miles in Van Nu… 1st owner drove an estimated 5,358 miles… No accident or damage reported to CARFAX…
Is the Mercedes Benz CLK based on the C class?
The standard CLK chassis is used, and while the current version is not based on the new C-Class platform, the AMG version of the CLK offers some special undercarriage components.
The flap may break due to wear or because of excessive carbon built up near the intake valves. Over time the plastic becomes brittle and eventually fails. Once the lever breaks the pull rod disconnects from the manifold air flap lever. The part is the same design for the M272 V6 and M273 V8 engines.
What happens if you leave the P2006 code on?
The P2006 code can have some serious symptoms if left for long periods of time. If the intake manifold runner flaps fail engine damage may ensue.
What is the P2006 OBD2 diagnostic trouble code?
The P2006 code is a generic OBD2 diagnostic trouble code relating to the intake manifold runner control circuit.
Are there any problems with the Mercedes GL450?
Check out our Mercedes-Benz GL450 overview to see the most problematic years, worst problems and most recently reported complaints with the GL450.
What causes the P2007 code on an intake manifold?
What causes the P2007 code? 1 Intake runner bank 2 that is defective or clogged 2 Wiring harness that has an open or short 3 Faulty electrical connection 4 Intake manifold runner control solenoid has failed
What does the P2007 OBD-II trouble code mean?
This code is similar to P2004, P2005, P2006, P2008, P2009, P2010 and P2015. The P2007 code means the intake manifold runner is stuck closed for bank 2.
What can be the cause of a p0303 error code?
While it is always beneficial when a problem’s cause is evident and easy to resolve, this specific error code can be caused by a number of factors, spanning from affordable to expensive. For example, the issue can stem from a faulty spark plug or wire, which in the grand scheme of things is relatively easy to repair.
What does a p0304 engine failure code mean?
A mechanical engine failure ; The P0304 error code indicates that the number four cylinder specifically is failing to fire. Symptoms To Look For. Any error code can be triggered by a faulty sensor.
What does the code P2004 on an intake manifold mean?
If you are like most people, you may not know what the intake manifold is, or what it means for it to be stuck open. What does the code P2004 mean? The intake manifold is the part of the engine that supplies the cylinder head with the mixture of fuel and air.
Why does my car have trouble code P2004?
You are probably wondering, “How do I fix trouble code P2004?” There are many things that might cause this problem, which means you need to determine the cause before you can fix it. Before you start, it may be helpful to research whether your car make and model commonly suffers from this problem.
What are the OBDII Codes for a Mercedes?
OBDII Codes definition for car manufacturer Mercedes: B0001. B0002. B0003. B0004. B0005. B0010. B0011. B0012.
What causes a Mercedes Benz to not start?
In most cases you will get a fault code related to one of the following: 1 ECM / PCM computer failure 2 Camshaft position sensor 3 Shifter Selector module 4 Fault codes related to driver authorization or immobilizer 5 Electrical problems
What are the problems with a Mercedes Benz?
Top 5 Mercedes-Benz no start problems 1 Engine Click, No Start 2 Engine Dies Right After It Starts 3 Car turns over, but it won’t start 4 The car makes a clicking noise but won’t start. Hint: Starter Problem or Low Battery 5 Key will not turn the ignition More …
Where can I find a 2004 Mercedes E Class E 320?
Get KBB Fair Purchase Price, MSRP, and dealer invoice price for the 2004 Mercedes-Benz E-Class E 320 Sedan 4D. View local inventory and get a quote from a dealer in your area. Home Car Values Price New/Used My Car’s Value Instant Cash Offer Cars for Sale Cars for Sale Sell Your Car Free Dealer Price Quote Vehicle History Report Find Local Dealers
What are the model codes for Mercedes Benz?
Pages in category “Mercedes-Benz model codes” 1 Mercedes-Benz R107 and C107 2 Mercedes-Benz SL-Class (R129) 3 Mercedes-Benz SLK-Class (R170) 4 Mercedes-Benz SLK-Class (R171) 5 Mercedes-Benz SLK-Class (R172) 6 Mercedes-Benz SL-Class (R230) 7 Mercedes-Benz SL-Class (R231)
How much does a Mercedes-Benz E 320 cost?
Mercedes-Benz E 320 Sedan $6,491 Envision Chrysler Dodge Jeep Ram Used 2003 Mercedes-Benz E 320 Sedan New Listing $6,969 Mercedes-Benz of Arcadia Used 2006 Mercedes-Benz E 350 Sedan $8,990 Nash Auto Used 2002 Mercedes-Benz E 320 Sedan $10,000 VW-BENZ Used 2005 Mercedes-Benz E 500 Sedan $11,431 Audi West Covina
What does code P2006 on OBD II mean?
Although generic, the specific repair steps may vary depending on make/model. If your OBD II equipped vehicle has stored a code P2006, it means that the powertrain control module (PCM) has detected that the intake manifold air control (IMRC) actuator for engine bank one is stuck in the closed position.
What does code P2006 stand for in PCM?
A code P2006 will be stored, and a malfunction indicator lamp may be illuminated, if the PCM doesn’t see a sufficient change in MAP or manifold air temperature as expected with the desired repositioning of the flaps (by the IMRC actuator).
How to find out if your car has a P2006 code?
Check the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P2006 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city.
What does the Mercedes Benz P2006 code mean?
What does this mean? Mercedes Benz Code = 0522 Diagnosis of tumble flap Intake manifold: Open circuit of sensor lines / Tumble flap shafts stick in the nonactuated position. (P2006) The cost to diagnose the P2006 MERCEDES-BENZ code is 1.0 hour of labor.
What are the diagnostic codes for Mercedes Benz?
Mercedes-Benz Diagnostic Trouble Codes (DTC) for 1996+ models Powertrain P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent
What do I need to diagnose a P2006?
A diagnostic scanner, a digital volt/ohmmeter (DVOM), and a reliable vehicle information source will be necessary when attempting to diagnose a code P2006. I would check technical service bulletins (TSB) for the particular symptoms, stored code/s, and vehicle make and model before beginning my diagnosis.
What does diagnostic trouble code DTC stand for?
This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to all 1996-newer vehicles (Nissan, Honda, Infiniti, Ford, Dodge, Acura, Toyota, etc.). Although generic, the specific repair steps may vary depending on make/model.