What is fault code b1859 on Mercedes Benz?

There is a known issue with poor connection in the lines to the steering column module that connect to the airbag for fault code B1859. There is a repair that involves repairing the wiring in the loom to this module as the SRS control module sees too high a resistance to the drivers airbag.

Where can I find the Mercedes Fault code?

Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes. The codes above are retrieved by plugging a diagnostic scanner into the OBD-II port located under the dash, and scanning for fault codes. Location of OBD II port used to retrieve Mercedes-Benz fault codes.

What is the fault code for a mid 128 engine?

Engine ECU Faults (MID 128) Fault Code Description FMI Codes MID 128 PID 26 Engine Fan Speed Percent 3,8 MID 128 PID 27 EGR Valve #1 Position Sensor 3,4,5 MID 128 PID 45 Preheater Relay Status 3,4,5 MID 128 PID 81 Particulate Filter 0,2,3,5,12

Where can I find all the OBD fault codes?

Our software contains all of the 11 000 codes. Don’t hesitate to download it. It is free and, using an ELM327 or ELM323 interface, can be used to read the fault codes. For more details, go to our EOBD-Facile car diagnostic software page. Thank you so much guys. Thia is a valuable tool in anyone’s toolbox. Thanks.

Is the b1628 turn signal lamp in module e2e5 defective?

B1628 Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. B1858 Two-way radio signal. The progammed code is ok, but the programmable code is not synchronised. B2708 ?

What’s the fault code for a 2001 Mercedes Benz?

Click to expand… For the ML class it does not apply to the 2001 models. Also the fault code in the bulletin is for DTC B9103 and DTC B9123. No others would be covered by the DTB. Post # 34 in this thread lists the DTB the parts, and all affected models.

What is the fault code for a D2B ring?

N1141 MCS fault code: Set-actual configuration of D2B ring differs from actual. N1241 CD fault, CD can not be read. 9260 SRS: resistance in drivers airbag too high. Replace Wiring. Please post a link to this string of posts in the Useful W163 Documents and the DIY Stickys at the top of this forum. done. good stuff.. Anyone know anything about it?

B1628 Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. B1858 Two-way radio signal. The progammed code is ok, but the programmable code is not synchronised. B2708 ?

What causes an EOBD fault code ( DTC )?

DTCs may also be triggered by faults earlier down the line. For example, a dirty MAF sensor might be causing the car to overcompensate in its fuel-trim adjustments. As a result, oxygen sensors are likely to report fuel mixture problems.

What are the OBDII Codes for a Mercedes?

OBDII Codes definition for car manufacturer Mercedes: B0001. B0002. B0003. B0004. B0005. B0010. B0011. B0012.

Do you need icarsoft adapter for OBD1 Mercedes?

While it’s made for OBD2 Benzes, the MB V2.0 also works on some OBD1 models. Specifically, you can use it on any Mercedes with chassis 201, 126, 124 and 107. You will, however, need to buy the 38-pin iCarsoft conversion adapter for an OBD1 Benz.

How can I tell if my Mercedes Sam is defective?

Next to confirm that the SAM unit is defective you should read the fault codes. For this you will need to see a mechanic that has Mercedes Star Diagnostic or use a scanner such as iCarsoft MB II. The fault codes will have enough information to tell you if this is a SAM module problem or not.

Which is the best OBD code reader for Mercedes Benz?

Top 3 OBD-2 code readers for Mercedes-Benz have been listed under the green column below. 1. OBD II Code Reading Scanners – For ECU Only 2. BlueDriver Scan Tool for iPhone and Android

Can you read the fault code on a Mercedes Benz?

Can read fault codes from multiple systems such as transmission, engine, ETS, airbag and more. Can clear fault codes. Can read and erase all fault codes on Mercedes-Benz cars. Only works on MB but can perform further troubleshooting including SBC brake systems, convertible systems, Air Conditioner (A/C) system. 3. Mercedes-Benz Star Diagnostic DAS

Where is the OBD II port on a Mercedes Benz?

The OBD II port is located under the dashboard, driver’s side. Look under the dash, over by the brake pedal. Here is an example of where it is located. Find the OBD II Port Location on my Mercedes-Benz

What does the Mercedes Fault code p0801 mean?

Mercedes Fault Code Fault Code Meaning; P0801: Reverse Inhibit Control Circuit Malfunction: P0803: 1-4 Upshift (Skip Shift) Solenoid Control Circuit Malfunction: P0804: 1-4 Upshift (Skip Shift) Lamp Control Circuit Malfunction: P0805: Clutch Position Sensor Circuit Malfunction: P0806: Clutch Position Sensor Circuit Range/Performance: P0807

What does Mercedes Fault code p0400 mean?

P0400 Mercedes Fault Codes Meaning Mercedes Fault Code Fault Code Meaning P0466 Purge Flow Sensor Circuit Range/Performa P0467 Purge Flow Sensor Circuit Low Input P0468 Purge Flow Sensor Circuit High Input P0469 Purge Flow Sensor Circuit Intermittent

How to erase diagnostic trouble codes in Mercedes medic?

Proceed to ERASING DIAGNOSTIC TROUBLE CODES. 1) After display window shows “En° d”, press AUTO push button once again. Display window should show “dE L” (delete). 2) To erase DTCs, simultaneously press down and up arrow push buttons for more than 5 seconds.

What is the code for Mercedes Benz air conditioning?

Also make note of the recharged bar pressure (17) – you can periodically check code 7 to make sure the system is holding the refrigerant pressure – if it decreases over time you have a slow leak and need to address it. Hope this helps and good luck! 2001 E55, 1999 C43. thanks!

Where is the SRS fault on the Mercedes E class?

Here is a way to deal with a common SRS fault that lies within the seat pad of the Mercedes E Class (W210). (I am sure also similar for other models)

What are the fault codes for Mercedes SRS?

Child seat:”Signal” transmission fault between front passenger seat and “Babysafe” Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. C1011. BAS light, play in steering column causes steering angle sensor to lose memory (?) C1401.

What causes a Mercedes SRS to lose memory?

Part E2e5 (Turn signal lamp) in module E2 (Right front headlamp unit) is defective. C1011. BAS light, play in steering column causes steering angle sensor to lose memory (?) C1401. BAS light, play in steering column causes steering angle sensor to lose memory (?) Driveline Disconn.

What causes a Mercedes SRS cable to break?

It is very common for the wires to and around this connector to break (seat-side) as they are very fine conductors indeed and this is compounded by a slight design flaw, in that the cable that enters the seat base to the matrix is tie-wrapped to a metal seat component which in turn causes a stress fracture along the wire length where fixed.

Where are the SRS lights on a Mercedes?

There are 3 wires to connect, colour for colour those that exist under the seat Brown, White and Red on the yellow connector. This resets the SRS lights as before on ignition power, without a star reset.

What are the diagnostic codes for Mercedes Benz?

Mercedes-Benz Diagnostic Trouble Codes (DTC) for 1996+ models Powertrain P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent

What does TPMS mean on a Mercedes Benz?

If the TPMS light on your Mercedes-Benz dashboard stays on, it means that at least one of your tires has low air pressure. Use a tire pressure gauge and make sure that the pressure is at least 36 PSI. Check air pressure on all four tires plus the spare.

What should the air pressure be on a Mercedes Benz?

Air pressure on the rear tires should be between 36 under normal load and 45 PSI for maximum load. If the TPMS light on your Mercedes-Benz dashboard stays on, it means that at least one of your tires has low air pressure.

What does the p1870 Chevrolet engine code mean?

Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. What does this mean? The cost to diagnose the P1870 CHEVROLET code is 1.0 hour of labor.

How much does it cost to repair a p1870 Chevy?

An error occurred while retrieving sharing information. Please try again later. What does this mean? The cost of diagnosing the P1870 CHEVROLET code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

Where are the fault codes on a Mercedes Benz?

Cut off line to Pin 11 (BNYE), Pin 12 (BU) and line to Pin 4 (YE) approx. 160mm after the connector (14-pin) of the frame floor system (FFS) wiring harness to the steering column tube (N80) and unpin from steering column tube module connector. Slide back the flexible cable set jacket and fix in place for this purpose.

What are the warning lights on a Mercedes Benz?

The following are warning lights and indicators found in vehicles built by Mercedes Benz. Click a link to learn more about each one. They are roughly ordered by importance, which tends to be by color (red, amber, yellow, orange, green, blue, gray), but there are over 40 of them so be patient!

What is the option code for Mercedes W123?

Some of the options became standard during the time a car series was built (e.g. code 422 Servolenkung SV/ power steering for W123 became standard since the beginning of modelyear 1983). Codes in the form of e.g. 42/2 power steering W114/115 denote the older code system.

What are the option codes for a 1995 Mercedes Benz?

I have some questions on the VIN Decoder for my 1995 E320 Convertible. There are some options for my car that I do not know what they mean as follows: 1. #283 – Draft Deflector – Is this the mesh assembly that cuts down on drafts when the top is down? 2. #494 – Version for USA – What is that?

Where is the level sensor on Mercedes Benz air suspension?

If you need help with troubleshooting the airmatic valve assembly watch this video. Level sensor is faulty They are located at the rear and front suspension. When they stop working the air suspension control unit may no longer be able to recognize the height of the car.

Is there a diagnostic scanner for Mercedes Benz?

Mercedes-Benz Star Diagnostic DAS This is diagnostic scanner used at Mercedes-Benz dealerships. Yes, it can do anything including programming of sensors and features. Any of the scanners listed above can read and clear the Check Engine / Service Engine Fault Codes.

Why did my Mercedes Benz HVAC blower go dead?

Today, the temp was a somewhat unusual 7 deg F here in the Metro Atlanta area. The car started pretty normally, but the HVAC blower was totally dead. After several errands, the wife and I went to Costco, filled up with premium, moved the car and went inside. During all of this time, the only fault was the dead blower.

What is the temp sensor on a Mercedes medic?

30 = left rear air conditioning heat exchanger temp sensor (not all vehicles; obviously) 40 = control module version software status (?) 43 = variant code second number.

How to remove DTCs from Mercedes A / C air conditioner?

1) After display window shows “En° d”, press AUTO push button once again. Display window should show “dE L” (delete). 2) To erase DTCs, simultaneously press down and up arrow push buttons for more than 5 seconds. The display window should show “- –“. If not erasing DTCs, press the AUTO push button. The permanent DTCs will again be displayed.

Navigation