How do you replace the brakes on a 1998 GMC Sierra?
Replacing the brakes on the 1998 GMC Sierra is a relatively easy task. Open the Sierra’s hood and remove approximately half of the fluid from the brake master cylinder using a turkey baster. Place this fluid in a clean container for reuse. Loosen the front lug nuts with a ratchet and socket, but don’t remove them yet.
What kind of brake line does a 1998 GMC CK have?
GMC CK Pickup 1998, Stainless Steel Braided Rear Drop Brake Hose by Fine Lines®. This automotive brake hydraulic hose was precision-engineered to match the fit, function, and performance of the original brake hose on specific vehicles… Universal Poly Coated Brake Hydraulic Line by Carlson®.
How to replace brake lines in a GMC Truck?
Try using and air bleeder first. Start at the right rear wheel. Let it suck on the system for a while. then over to left rear. That always works for us. Thanks guys. Yeah just replaced the lines as they were all really rusted and 1 blew. Brake fluid was a dark brown but nothing like sludge.
What kind of engine does a 1998 GMC Sierra have?
The 1998 C-1500 Sierra came standard with a 4.3-liter V-6 engine that produced 200 horsepower; it also came standard with front disc brakes. Replacing the brakes on the 1998 GMC Sierra is a relatively easy task.
Can a brake line rupture on a GM Truck?
Adler said that since the front and rear brakes are on different lines, drivers should be able to stop even if one of the lines ruptures. “GM does not see the rusty brake lines as a threat to safety because the brakes will stop the trucks,” he told ConsumerAffairs.
How much does it cost to replace a brake line on a GM Truck?
“Brake failure and systemic corrosion required replacement of all brake lines on the vehicle: master cylinder through ABS module to each wheel cylinder” at a cost of $2,195. GM’s Adler said it shouldn’t cost that much. “Time studies for the repair showed it should take four to 4 1/2 hours based on $100 an hour for labor for a total cost of $500.
What are the brake lines on a Chevy Silverado?
The brake lines used in all GMT800 Silverado/Sierra/Suburbans are a copper plated steel tube. The lines are then coated with an “AlGal” coating to protect them from corrosion.
Are there any brake lines that need replacement?
The brake lines in 1999-2007 GMT800 Silverado’s, Sierra’s, and Suburbans are very prone to rusting out and needing replacement. For individuals who live in “salt” states, where cities commonly salt the roads to prevent ice, the brake line rusting is even more common.
How do you change the rotor on a GMC Sierra?
Slide the rotor on the GMC’s spindle and place the outer bearing, tapered end first, into the hole in the center of the rotor. Reinstall the washer and nut on the spindle and tighten the nut, while spinning the rotor, to 12 foot-pounds with a torque wrench and socket to seat the bearing. Loosen the spindle nut and tighten it to only hand-tight.
What’s the name of the GMC Sierra truck?
The C-series indicated two-wheel drive and the K-series indicated four-wheel drive. In 1975, the names of the trim levels on GMC trucks changed to Sierra, Sierra Grande, High Sierra and Sierra Classic with the Sierra trim level being the base level GMC C-K pickup.
Replacing the brakes on the 1998 GMC Sierra is a relatively easy task. Open the Sierra’s hood and remove approximately half of the fluid from the brake master cylinder using a turkey baster. Place this fluid in a clean container for reuse. Loosen the front lug nuts with a ratchet and socket, but don’t remove them yet.
How to fix rear drum on Chevy Silverado?
That should do the trick. Remove the hub caps from the rear wheels and break the lug nuts loose with the lug wrench. Lift the rear of the vehicle with the floor jack and secure it onto the jack stands. Remove the nuts and wheels. Locate the adjusting porthole on the back of the backing plate.
Slide the rotor on the GMC’s spindle and place the outer bearing, tapered end first, into the hole in the center of the rotor. Reinstall the washer and nut on the spindle and tighten the nut, while spinning the rotor, to 12 foot-pounds with a torque wrench and socket to seat the bearing. Loosen the spindle nut and tighten it to only hand-tight.
The 1998 C-1500 Sierra came standard with a 4.3-liter V-6 engine that produced 200 horsepower; it also came standard with front disc brakes. Replacing the brakes on the 1998 GMC Sierra is a relatively easy task.
When did GMC Sierra change to two wheel drive?
In 1962, General Motors changed the name of Chevrolet and GMC pickups to C- and K-series. The C-series indicated two-wheel drive and the K-series indicated four-wheel drive.
In 1962, General Motors changed the name of Chevrolet and GMC pickups to C- and K-series. The C-series indicated two-wheel drive and the K-series indicated four-wheel drive.