What does the sprint dial code for ERR mean?
This dial code toggles Passthrough. “ERR.” is short for “ERROR”. This Sprint Dial Code displays the last error which caused a soft reset, what program was running, line number, etc. Not yet verified but it appears this dial code should display the device ESN number. This hash code launches network settings to force RTT or EVDO.
How to reset service indicator on MB sprinter?
1. Switch on ignition. If the exceeding of the maintenance interval is shown in the display, you have to wait until the readout in the display automatically jumps over to total km. Only then is it possible to get into the service menu. 2. Press button 0 on the instrument cluster for approximately 30 seconds until a beep sounds. 3.
What causes a sprinter to go into limp home mode?
This is common condition with a few common causes. If you have an Sprinter with the 4-cylinder engine (OM651) see this article about a common issue on this engine that causes Limp Home Mode. Low power – enough power to get to 50 mph in some cases, but not to keep that speed up a hill.
What should the rail pressure be on a Sprinter diesel?
Check rail pressure when engine is off, it should be 0 PSI (+/- 500 PSI). Aerated or restricted fuel supply. Excessive idle time can cause white smoke when cold due to carbon build up on injector tips. More than 20% idle time is excessive. 2007-2009 model years use an electric supply pump in the tank to feed the CP pump at 59 +-2 PSI.
When does the Def warning light come on in a sprinter?
Description: The yellow Mercedes Sprinter DEF – diesel exhaust fluid warning light comes on with the engine running when the exhaust gas aftertreatment system has malfunctioned or the level of Diesel Exhaust Fluid (DEF) is running low.
This is common condition with a few common causes. If you have an Sprinter with the 4-cylinder engine (OM651) see this article about a common issue on this engine that causes Limp Home Mode. Low power – enough power to get to 50 mph in some cases, but not to keep that speed up a hill.
Is there an owner’s manual for a Mercedes Sprinter?
The Owner’s Manual doesn’t address the technical problems. Mercedes tells dealers to explain things like fuel dilution and the DPF regeneration, but dealers don’t have time or the manpower. Plus it’s not in the dealers financial interest to tell owners how to prevent problems.
Why does the Mercedes Sprinter check engine light go out?
The Mercedes Sprinter check engine light has several potential faults associated with it. • Exhaust gas after-treatment malfunction. The Mercedes Sprinter preglow / glow plugs warning light comes on for a short time only and goes out when the diesel engine is ready to start. Symptoms of a possible fault are:
What to do when you get an error code from Dell?
Refix the HDD and run Diagnostics if you receive the same error code Replace the HDD. Refix the Optical Drive and run Diagnostics if you receive the same error code Replace the Optical Drive. An out of date BIOS can cause any of these error codes. Downloads the Updated BIOS from DELL Web Site.
How to find the USSD code on a cell phone?
Universal USSD codes. 1 Field Mode: *3001#12345#*. Type *3001#12345#* into your dialer and then press the call button to access “Field Mode,” which can give you access to 2 Display your IMEI: *#06#. 3 Check Your Call Forwarding: *#67#.
What does the ERR code on a cell phone mean?
Shows all cellular radio debug info, including 1x Engineering RF, 1x Engineering RF, EVDO Engineering RF, EVDO Engineering Protocol, LTE Engineering, Configuration, Bluetooth, Data Status, eHRPD, Memory, Active APN Connections & Others. This dial code toggles Passthrough. “ERR.” is short for “ERROR”.
Refix the HDD and run Diagnostics if you receive the same error code Replace the HDD. Refix the Optical Drive and run Diagnostics if you receive the same error code Replace the Optical Drive. An out of date BIOS can cause any of these error codes. Downloads the Updated BIOS from DELL Web Site.
What do the last three digits on a diagnostic code mean?
The last two numbers refer to the actual component or area the first three digits represent. Example: P0301, the “P” would represent the “powertrain,” the “0” represents it’s a generic code (OBD II), the “3” represents it’s an ignition misfire, and the last two digits represent which cylinder it has detected the misfire on.
How to call Rockwell Automation for technical support?
1.888.382.1583 (toll free) or1.440.646.3434 Monday through Friday from 8:00am to 6:00pm ET. TechConnect Support Direct Dial Numbers For customers with Active TechConnectSMSupport contracts For online technical support: rockwellautomation.com/knowledgebase Select Option 3 1Technical Support Select Option 5
What does the second digit after DTC mean?
The first digit following the DTC indicates the symptom category, while the second digit refers to the subsystem or more in-depth information about the symptom. There are 16 possible symptom categories available for 0 to 9 and A to F. Currently, there are only eight categories in use, 0 through 7.