What are the P codes for fuel metering?
P0XXX Codes Trouble Code Fault Location Probable Cause P0000 – P0099 (Fuel and air metering and auxiliary emission control) P0000 No fault P0001 Fuel volume regulator control -circuit open Wiring, regulator control solenoid P0002 Fuel volume regulator control -circuit range/performance Wiring, regulator control solenoid
What are the DTC codes for air metering?
DTC Codes – P0100-P0199 – Fuel and Air Metering P0100 Mass or Volume Air Flow Circuit Malfunction P0101 Mass or Volume Air Flow Circuit Range/Performance Problem P0102 Mass or Volume Air Flow Circuit Low Input P0103 Mass or Volume Air Flow Circuit High Input P0104 Mass or Volume Air Flow Circuit Intermittent
What are the symptoms of a bad air fuel ratio sensor?
1. Decrease in fuel efficiency One of the first symptoms of a problem with an air-fuel ratio sensor is a decrease in fuel efficiency. The air-fuel ratio sensor monitors the oxygen content in the exhaust stream and sends data to the computer so that it can add or subtract fuel.
What happens if the evaporative emission control system fails?
The Evaporative Emission Control System, commonly referred to as EVAP, is designed to detect gasoline vapors if they are evaporating out of the filler hose. If the system fails it will result in a great decrease in fuel efficiency.
What does p142e mean on a fuel pump?
p142e means fuel pressure to low, your high pressure fuel pump is failing. Also need to have this taken care of asap or the car may leave you stranded on the side of the road symptoms sometimes include sluggishness misfires bucking, or jerking.
What are the P codes for mechanical fault?
P0016 Crankshaft position/camshaft position, bank 1 sensor A -correlation Wiring, CKP sensor, CMP sensor, mechanical fault P0017 Crankshaft position/camshaft position, bank 1 sensor B -correlation Wiring, CKP sensor, CMP sensor, mechanical fault
What is the p code for a fuel volume regulator?
P0001 Fuel volume regulator control -circuit open Wiring, regulator control solenoid P0002 Fuel volume regulator control -circuit range/performance Wiring, regulator control solenoid P0003 Fuel volume regulator control -circuit low Wiring short to earth, regulator control solenoid P0004
What does the error code p1423 stand for?
Error Code P1423 is defined as Secondary Air Injection System Bank 1 Insufficient Flow Detected. This indicates a problem with the secondary system. This error code is a manufacturer-specific trouble code, meaning it does not apply to all vehicles makes. Rather, it applies only to specific vehicle makes, such as Toyota.
How to diagnose p1423 secondary air injection system Bank 1?
Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P1423 code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
What are the p02xx OBD-II DTC trouble codes?
This is the listing of P02xx OBD-II diagnostic trouble codes (DTCs). They all start with P02 (e.g. P0230, P0299, etc.), the first letter P designates they are powertrain related codes, the next digits 02 indicates they are fuel & air metering injector circuit related codes.
What are the symptoms of powertrain code p0155?
Code P0155 occurs when the powertrain control module tests the upstream heated oxygen sensor’s heater circuit on Bank 2 and detects a short in the circuit or excessive resistance in the heater circuit. What Are The Symptoms Of Code P0155?
What does the first letter of a powertrain code mean?
They all start with P00 (e.g. P0022, P0093, etc.), the first letter P designates they are powertrain related codes, the next digits 00 indicates they are fuel & air metering and auxiliary emission control related codes.
Are there any OBD-II powertrain trouble codes?
The codes below are considered generic because they apply to all OBD-II makes/models of vehicles, although specific diagnosis repair steps may vary. We have literally thousands more codes listed on the site, use the links below to go to the other code listings.
What are the OBD codes for fuel trims?
For more information on what OBD codes are , OBD-II codes explained, explanation of fuel trims, or answers to other questions, visit our FAQ area. The most common OBD-II codes are P0___ powertrain codes, which are linked below on this page, along with P2___ generic & P3___ generic codes.
What are the P codes for an engine?
P0012 Camshaft position (CMP), intake/left/front, bank 1 timing over -retarded Valve timing, engine mechanical fault, CMP actuator P0013 Camshaft position (CMP) actuator, exhaust/right/rear, bank 1 -circuit malfunction Wiring, CMP actuator, ECM
What is the fault code on an Intl 9200i?
No International engines have a 197 fault code. If your truck has a Cummins engine, 197 is for low coolant level. 3HTrucking and Captredbeard Thank this. I have 4 fault codes on my 2005 Intl 9200i, ISM Cummins.