What does the p2402 OBD-II code mean?
All our repairs are backed by our 12-month / 12,000-mile warranty. What the P2402 code means? P2402 is an OBD-II generic code for the engine control module (ECM) detecting the evaporative system leak detection pump control circuit has a high voltage signal return.
What does the code p2402 on an evaporative pump mean?
Code P2402 is an indication that the evaporative pump is shorted internally and other than failing emission tests and the check engine light being on, should not cause any drivability problems. What repairs can fix the P2402 code? Replace the evaporative pump and fuse. Replace the evaporative pump relay.
How much does it cost to diagnose a p2402 Toyota code?
The cost to diagnose the P2402 TOYOTA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars?
How much does a p2402 leak detection pump cost?
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P2402 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.
What does the OBD code p2402 stand for?
OBD-II Code P2402 is defined as a Evaporative Emission System Leak Detection Pump Control Circuit The Leak Detection Pump is part of the Evaporative Emissions System. After the vehicle has been sitting for a few hours, this pump will turn on and create a vacuum in the EVAP system. The engine computer (PCM) runs this test when the vehicle is off.
How much does it cost to fix a p2402 code?
The cost of diagnosing the P2402 code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour. Engine Light ON (or Service Engine Soon Warning Light)
Code P2402 is an indication that the evaporative pump is shorted internally and other than failing emission tests and the check engine light being on, should not cause any drivability problems. What repairs can fix the P2402 code? Replace the evaporative pump and fuse. Replace the evaporative pump relay.
Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P2402 code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type. Most auto repairs shops charge between $75 and $150 per hour.
What is the OBD code for the EVAP leak detection pump?
P2402 is an OBD-II generic code for the engine control module (ECM) detecting the evaporative system leak detection pump control circuit has a high voltage signal return.
What is the code for the evaporative pump?
Code P2402 for the evaporative pump is drawing more amps than specified. This is common on higher mileage vehicles after the pump has gotten worn or if the pump relay sticks on and runs the motor continuously until the pump burns out. Test for this when replacing the bad pump.
What is the OBD code for a leak detection pump?
OBD-II Code P2402 is defined as a Evaporative Emission System Leak Detection Pump Control Circuit. The Leak Detection Pump is part of the Evaporative Emissions System.
When does the PCM set the code p2402?
If the PCM does not see the Leak Detection Pump activate as requested, or does not see a vacuum created in the EVAP System, the PCM will set code P2402.
Can a large leak cause trouble code p0455?
Any large leak in your evaporative emission control system, or EVAP system, can signal trouble code P0455. You may be wondering, how do I fix trouble code P0455?