How do you replace the fuel injector on a Mazda 3?
1. Apply a small amount of clean oil to the fuel injector groove and the new O-ring, and assemble them. 2. Temporarily attach a new clip to the fuel injector groove. When the clip is attached correctly, the central area of the fuel injector and the clip finger positions are aligned.
How to remove the air intake in a Mazda 3?
1. Set the air intake mode to FRESH. 2. Disconnect the negative battery cable.. 3. Remove the following parts: a. Front scuff plate (Passenger-side). b. Front side trim (Passenger-side). c. Resistance Inspection NOTE: Because the IAT sensor is integrated in the MAF sensor, replacing the IAT sensor includes replacement of the MAF/IAT sensor. 1.
How to remove fuel rail and intake manifold?
CPE has a slid hammer that works if you can get your hand on one of those, it will make it easier to pull out the injector. You have now removed your IM, fuel rail, and injectors. When putting back together, just work the instructions backwards and you should be fine.
What happens if fuel spills in Mazda 3?
Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin and eyes. To prevent this, always complete the “Fuel Line Safety Procedure”, while referring to the “BEFORE SERVICE PRECAUTION”.
1. Apply a small amount of clean oil to the fuel injector groove and the new O-ring, and assemble them. 2. Temporarily attach a new clip to the fuel injector groove. When the clip is attached correctly, the central area of the fuel injector and the clip finger positions are aligned.
How do you remove fuel line from intake manifold?
There are 2 bolts (10mm) connecting the fuel rail to the fuel line that are in the blue circle. And finally there is a hose with a yellow clip that needs to be removed which in in the yellow circle. Just pry the yellow clip off, but be careful and don’t lose it or break it.
1. Set the air intake mode to FRESH. 2. Disconnect the negative battery cable.. 3. Remove the following parts: a. Front scuff plate (Passenger-side). b. Front side trim (Passenger-side). c. Resistance Inspection NOTE: Because the IAT sensor is integrated in the MAF sensor, replacing the IAT sensor includes replacement of the MAF/IAT sensor. 1.
Fuel is very flammable liquid. If fuel spills or leaks from the pressurized fuel system, it will cause serious injury or death and facility breakage. Fuel can also irritate skin and eyes. To prevent this, always complete the “Fuel Line Safety Procedure”, while referring to the “BEFORE SERVICE PRECAUTION”.
How to drain the fuel tank in a Mazda 3?
Connect a long hose to the disconnected quick release connector and drain the fuel into a container used for collecting gasoline. 5. Drain the fuel from the fuel tank using the following procedure: Connect the M-MDS to the DLC-2. Using the simulation function “FP”, start the fuel pump.. Remove the battery cover..
What causes a Honda Jazz fuel injector to leak?
Leaking fuel injectors are often caused by a bad a crack in their body. When this occurs they must be replaced. If the injectors are clogged you’ll need to have them cleaned by a professional. When they are dirty but not yet clogged, you may be able to clean them with a good fuel injector cleaner.
What are the symptoms of bad fuel injectors?
The symptoms of bad fuel injectors are going to feel almost the same as a bad fuel pump or fuel filter . That’s why it’s important to check the fuel pressure at the rail before replacing injectors, otherwise you may end throwing good money after bad. If you do end up needing to replace the injectors, they are somewhat affordable.
How to remove the PS pump in a Mazda?
For this, you will first need to remove the serpentine belt via the tensioner pulley with a 14mm. Then remove 3 bolts (12mm) holding the PS pump (the top left one, once backed out will not be removed completely). The third one is hidden below but the arrow shows you where it is below.