What is the wiring diagram for a Mazda Protege?

Listed below is the vehicle specific wiring diagram for your car alarm, remote starter or keyless entry installation into your 1999-2002 Mazda Protege . This information outlines the wires location, color and polarity to help you identify the proper connection spots in the vehicle.

Why does my Mazda Protege crank but not start?

It could be the valve timing, spark plug, fuel injection, or ignition timing. If not then it may also be a clog in the fuel line if you let it sit on a downward slope for a few days. Mine was clogged when I was on vacation and mine would crank but would not start.

Why does my Mazda Protege make no noise?

Does it start when you try jumping it. It can also be a bad starter although this will normally have a clicking noise or no noise instead of a cranking noise. It could be the valve timing, spark plug, fuel injection, or ignition timing. If not then it may also be a clog in the fuel line if you let it sit on a downward slope for a few days.

What kind of resistor does a Mazda Protege need?

NOTE #1: THIS IS A 1-WIRE DOOR LOCKING SYSTEM, TO LOCK REQUIRES A (-)NEGATIVE THRU A 1500 OHM RESISTOR. TO UNLOCK REQUIRES A STRIGHT (-) NEGATIVE TO THE SAME WIRE.

Where is tach located on a Mazda Protege?

CAN ALSO FIND TACH IN PIN 48 OF THE ECM (ELECTRONIC CONTROL MODULE). NOTE #3: THE DOOR LOCK RELAYS ARE LOCATED, TO THE DRIVERS SIDE OF THE BRAKE PEDAL.

When to replace the relay on a Mazda Protege?

– If not as specified, replace the relay. fPage 361 fCamshaft Position Sensor: Service and Repair fCAUTION: When foreign material such as an iron chip is on the CMP sensor, it can cause abnormal output from the sensor because of flux turbulence and adversely affect the engine control.

How to change the ECT sensor on a Mazda Protege?

Place the ECT sensor in water with a thermometer, and heat the water gradually. Specification 4. Measure the resistance between the ECT sensor terminals A and B using an ohmmeter. – If not as specified, replace the ECT sensor.

How do you check the PCM on a Mazda Protege?

PCM Inspection Using the SST (104 Pin Breakout Box) 1. Disconnect the negative battery cable. 2. Disconnect the PCM connector. 3. Connect the SST (104 Pin Breakout Box) to the PCM as shown. 4. Tighten the connector bolt. Tightening torque 7.9 – 10.7 N.m {80 – 110 kgf.m, 69.5 – 95.4 in.lbf} 5. Connect the negative battery cable.

NOTE #1: THIS IS A 1-WIRE DOOR LOCKING SYSTEM, TO LOCK REQUIRES A (-)NEGATIVE THRU A 1500 OHM RESISTOR. TO UNLOCK REQUIRES A STRIGHT (-) NEGATIVE TO THE SAME WIRE.

CAN ALSO FIND TACH IN PIN 48 OF THE ECM (ELECTRONIC CONTROL MODULE). NOTE #3: THE DOOR LOCK RELAYS ARE LOCATED, TO THE DRIVERS SIDE OF THE BRAKE PEDAL.

What do you need to know about Mazda wiring?

These Mazda Wiring information / Aftermarket Autostart/Alarm Technical Wiring Diagrams are very useful, if not required, for the installation of alarms, autostart / alarms, remote starts, doorlock info and any other aftermarket installation that would require you to know the / Wire Information / Wiring Information of your Mazda

When did the Mazda Protege repair manual come out?

We’ve checked the years that the manuals cover and we have Mazda Protege repair manuals for the following years; 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 1999, 2000, 2001, 2002 and 2003. Go through the 48 different PDF’s that are displayed below, for example this one.

Navigation