How to change the alternator belt in a car?
Work in reverse, start with the alternator belt. Slip on the new belt, and torque the pivot locking bolt to spec (you can hand tight the locking bolt.) Adjust the tension of the belt. Step 9. Install the water pump/AC belt. Tighten the idle pulley locking nut and adjust the tension of the belt as needed. Step 10. Install the power steering belt.
How do you change the belt on a water pump?
If you have to install a v-belt, slide the tensioner over and tighten it. Make adjustments to the v-belt by loosening and tightening the tensioner until the belt is loose to its width or about a 1/4 inch. Step 13: Pick up all tools used to change the water pump belt. Step 14: Remove the wheel chocks and put them aside.
How do you install a serpentine belt on a water pump?
If you have to install a serpentine belt, use the breaker bar to relax the tensioner and slide the belt onto the last pulley. If you have to install a v-belt, slide the tensioner over and tighten it. Make adjustments to the v-belt by loosening and tightening the tensioner until the belt is loose to its width or about a 1/4 inch.
Where does the serpentine belt go on an alternator?
If you do not have a diagram on the vehicle or in your service manual laying out the direction your serpentine belt travels through the pulleys, take a picture of it with your phone to refer to when installing the new belt. A strictly alternator belt will likely only go around an alternator pulley and the crank pulley at the bottom of the engine.
Can a serpentine belt be replaced in an alternator?
This article will educate you on how to replace alternator belt. An alternator belt also known as a serpentine belt is a continuous, solitary belt that is used to drive numerous devices in an automotive engine, such as power steering pump, alternator, air conditioner compressor, air pump, water pump, and other accessories.
What do you need to know about alternator belts?
This article will educate you on how to replace alternator belt. An alternator belt also known as a serpentine belt is a continuous, solitary belt that is used to drive numerous marginal devices in an automotive engine or a car engine, such as power steering pump, alternator, air conditioner compressor, air pump, water pump, and other accessories.
How do you remove an alternator from a Toyota Camry?
Loosen the two mounting screws by using the 12 and the 14mm sockets. Then, loosen and back out the tension screw to allow enough slack in the belt to pull it off of the alternator pulley. Next, remove the two fasteners you loosened earlier. Now, pull the alternator out by rocking it back and forth until it comes off completely.
How do you remove the harness from an alternator?
Using your 10mm socket wrench, remove the nut from the terminal. Next, remove the wire harness connection by pinching and squeezing the release located on the harness connector. Now, remove the cable and harness from the alternator mount by pushing in the mounting clip and pulling the wires free. Figure 2. Disconnect cable and harness.
How much does it cost to replace an alternator?
Replacing an alternator can cost you several hundred bucks at the local repair shop, but it’s one of the simplest repairs you can do at home. With a few tools and about an hour you can swap it out yourself — and keep your dough in your pocket where it belongs.
Can a manual tensioner be used to replace an alternator?
The belt tensioner will only travel (swing) so far which can make installing the belt difficult. Never pry or force the belt onto the pulley. Vehicles with a manual tensioner or the belt tightens with the alternator, there should about ½ inch of deflection in the belt between the pulleys with the greatest distance between them. 7
How can I tell if I need to replace my alternator?
Once the electrical connections, drive belt and any interference items are inspected, disconnected and removed, the old alternator can be unbolted from the engine and mounting brackets. Match it Up! Compare the old alternator to the replacement alternator.
How much should it cost to replace an alternator belt?
The replacement cost of an alternator belt is typically between $100 and $200 . The part cost is between $25 and $80 while the labor cost is between $75 and $120. Nov 4 2019
How much is the labor to replace an alternator?
Most often, labor on an alternator replacement is billed at book time. Parts costs can vary widely. A typical aftermarket alternator, new or remanufactured, can vary from $150 to $300 . New OE alternators through a dealership range from $400 to $600 on average. Nov 9 2019
How often should you change alternator belt?
Under normal conditions, the belt needs to be replaced every 4 to 6 years. However, those living in areas where the temperature and humidity can vary greatly throughout the year may need to change it more frequently.
How much does it cost to install an alternator?
The alternator cost will range from $200 to $700 just for the part itself! To have a new alternator fitted at a garage you can expect to pay between $172 to $1046 with an average cost in the mid $500 range, depending on the part used and the model of car you own.The Complete Alternator Replacement Cost Guideautoservicecosts.com/alternator-replacement-cost/