What kind of problem does a Mazda 626 have?
I have a Mazda 626 4 cyl. 1995. It was run off in a ditch and then drove home. After it was shut off it would not start back, the lights inside or outside wont do anything. There is no fire from the fuse box.
What causes a gasket on a Mazda 626?
Pump Problems The transmission pump on your Mazda 626, regardless of its model year, is prone to gasket problems. This pump provides continuous hydraulic fluid to the torque converter. The speedometer gear in your pre-1994 Mazda 626 may suddenly fail, which causes the meter to give imprecise readings.
How much does it cost to change the transmission on a Mazda 626?
Same as the diagnosis test done at Mazda last week cost me $300 instead of $79.95 as the mechanic had to do all these tests and take it out for a test drive – the hours were counted and I had to pay to find out it was the transmission – and after all that – transmission is ok – it was the Transmission Range Switch which needed to be changed.
What causes the O / D light to flash on a Mazda 626?
He said that when the O/D light “flashes”, it is caused by a malfunction within the computer or a minor defect in the transmission.
Is it right to buy a manual transmission in a Mazda 626?
The right thing to buy in these cars is a manual transmission. The one in my ’99 ES V6 has been absolutely bulletproof – still performing like new at 176k miles. Clutch has seemingly failed at about 145,000. It failed at about 90,000 and had it replaced for $900.
He said that when the O/D light “flashes”, it is caused by a malfunction within the computer or a minor defect in the transmission.
How much does a transmission cooler cost on a Mazda 626?
Keep in mind that once your car goes in safe mode, your transmission fluid will get burnt up real fast. A transmission cooler cost about 40-50 bucks, and will extend the life of the poorly designed Mazda/Ford transmission.
What is TSB 05-005 / 02 for Mazda 626?
TSB 05-005/02 deals with one specific circumstance: “After extended highway driving, the O/D off light is blinking and code P1783 is set (excessive ATF temperature). Occasionally there will be overflow through the dipstick tube and harsh shifting.
Where does Ford build the Mazda 626 car?
Ford owns a controlling interest in Mazda, and the 626 is built at a plant near Detroit that the two companies share. Designed in Japan, the sedan uses Mazda engines, and its front-drive platform also serves as the basis for the compact Mazda Tribute and Ford Escape sport utility vehicles.
How big is the back of a Honda 626?
With a wheelbase that stretches to just over 105 inches, the 626 sedan measures 187.4 inches long overall just slightly shorter than the Honda Accord and Toyota Camry. The 626 is 69.3 inches wide and 55.1 inches tall. Seating five occupants, the 626 has front buckets and a three-place rear bench with a split, folding rear seatback.
Where does the Mazda6 get its powertrain from?
Ford also plans to offer a hybrid powertrain on the platform. The official Mazda chassis codes are GG (saloon/hatch) and GY (estate) series – following the 626/Capella in its GF/GW series. Mazda’s Hofu Plant in Yamaguchi Prefecture, Japan produced the Mazda6 for international markets from February 2002 to August 2007.
I have a Mazda 626 4 cyl. 1995. It was run off in a ditch and then drove home. After it was shut off it would not start back, the lights inside or outside wont do anything. There is no fire from the fuse box.
How does a starter work on a Mazda 626?
A reliable Mazda 626 starter from AutoZone supplies the force that starts your engine. The starter’s work begins when you turn the key into the crank position. A 12-volt battery sends an electrical signal to the components of the motor to turn the engine over.
What should the ignition rpm be on a Mazda 626?
The essential engine rotation for the ignition process is between 85 and 150 RPMs. Starters for Mazda 626 use a high-amperage electrical battery to give enough juice to rotate your engine to get you going.