How does trouble code work on Mazda B2200?

0.4 second flashes indicate the ‘units’ of the trouble code A 1.6 second pause (MIL OFF) separates ‘TENS’ and ‘UNITS’ Depress the brake pedal for a minimum of 5 seconds Jump test connector (green, 1 pin) to ground Image 1 [1] Connect LED test lamp between DLC terminals Image 1 [2] Switch ignition ON.

What does code 0120 mean on Mazda OBD 1?

No short flashes in a group indicate ‘0’. For example: Trouble code 0120 displayed Fig. 3 . Switch ignition OFF. Rectify faults as necessary. Ensure ignition switched OFF. Disconnect battery earth lead for at least 30 seconds. Depress brake pedal for at least 20 seconds. Reconnect battery earth lead.

How to find the trouble code on a Mazda?

Ensure ignition switched OFF. Jump test connector (green, 1 pin) to ground Image 1 [1] Connect LED test lamp between data link connector (DLC) terminals 1 and 2 Image 1 [2] Count LED flashes and compare with trouble code table 1.2 second flashes indicate the ‘tens’ of the trouble code 0.4 second flashes indicate the ‘units’ of the trouble code

How long does it take to get a check engine light code?

However, it only checks for output device malfunctions in a 3 second period after the ignition switch is turned “ON” with test connector grounded. If there is more than one malfunction code present, the lowest number code is displayed first, followed by subsequent codes in numerical order.

What is error code 17 on Mazda MX-5?

Here shown with MX-5 (no errors) and 626 (error code 17, something wrong with oxygen sensor). You can find the meaning of the codes over the web. Be careful while doing that. You might burn something expensive. Do it on your own responsibility. Music by Teddybears/Cobrastyle. Loading…

Where is the OBD plug-in on a 92 B2600i pick up?

Mazda b2600i: where is the OBD plug-in on a 92 b2600i pick… where is the OBD plug-in… where is the OBD plug-in on a 92 b2600i pick-up Show More Show Less Ask Your Own Mazda Question Share this conversation Answered in 3 minutes by: 9/4/2012 Mazda Mechanic: Ron Z., – Mazda Tech – replied 8 years ago Ron Z., – Mazda Tech – Category: Mazda

Why does my 92 Mazda B2600i run rough?

My 92 Mazda B2600i 4×4 manual runs rough until you hit a higher rpms just had the timing done and new fuel filter and fuel pumps, any help would be great … read more Pete Automotive Diagnostic Specialist

What’s the towing capacity of a 1998 Mazda B2600?

The 1998 Mazda B2600 carries a braked towing capacity of up to 1500 Kg, but check to ensure this applies to the configuration you’re considering. Check out real-world situations relating to the Mazda B2600 here, particularly what our experts have to say about them. What ute is a good first car?

Where is the diagnostic link connector on a Mazda?

Mazda Engines – Please select the connector for your vehicle from the options below. This is an OBD2 / EOBD standard 16 pin data link connector. To get a list of codes that relate to this system click here. This connector is usually located under the driver side dash panel. Diagnostic Link Connector No. 73.

Where are the connectors on a Mazda engine?

Mazda Engines – Please select the connector for your vehicle from the options below. This connector is usually located under the driver side dash panel. Locations: Left-hand side of firewall. Near or in the fuse box, or near the battery. Next to the airflow meter or battery.

How to tell if a Mazda headlamp is at fault?

Trace in RED the portion of the circuit below that you suspect could be at fault. The LEFT HIGH BEAM HEADLAMP does not work in the High Beam Position. Both lamps function normally in the low beam position. The tail lamps function correctly. 3. Trace in BLUE the portion of the circuit below that you suspect could be at fault.

How to read Mazda OBD code without OBD scanner?

Connect LED test lamp between terminals FEN and B+ Fig. 1 . NOTE: Connect LED test lamp positive connection to DLC terminal B+. Switch ignition ON. Count LED flashes. Note trouble codes. Compare with trouble code table.

Where is the Check Engine Light code on a Mazda Bongo?

These are the main check engine light codes for MECS-II 626’s. You put the car into diagnostic mode by using a jumper wire between the C (TEN) & E (GROUND) pins of the diagnostic box under the hood of your car.

How do you find the trouble code on a Mazda?

Step 4 – The check engine light will start to blink, count the number, this will be the first number of the two digit trouble code. For example, if the light blinks two times and then pauses, the first number of the code is 2.

Why does my Mazda B2600 engine not start?

RAN GREAT, DROVE IT 45 MINUTES, TURNED IT OFF WILL NOT START AGAIN.I HAVE NO SOLUTION AND AM VERY FRUSTRATED, PLEASE PLEASE HELP. Was running fine. Quit 15 miles from home sort of. Still would idle and could just press on the throttle for high idle but would cut out at 1500 RPM.

What does trouble code 12 on Mazda OBD mean?

For example: Trouble code 12 displayed Fig. 2 . Each trouble code consists of four groups. A long flash indicates the start of each group Fig. 3 [A]. Short flashes indicate the digits of each group Fig. 3 [B]. No short flashes in a group indicate ‘0’. For example: Trouble code 0120 displayed Fig. 3 . Switch ignition OFF.

How can I remove a trouble code from a Mazda?

Disconnect battery ground cable for a minimum of 10 seconds, then depress brake pedal five times to clear trouble code’s stored in the memory. Connect SST (NGS) tool to data link connector 2. Then select “Clear Diagnosis Codes” function and erase diagnostic trouble codes from the NGS memory.

Which is the correct code for a Mazda check engine light?

1 Refer to our Generic OBD II code list for definitions on all other Mazda diagnostic trouble codes. 2 Manufacturer Specific Codes 3 P1000 4 P1001 5 P1100 6 P1101 7 P1102 8 P1103 9 P1110 10 P1112 11 P1113 12 P1114 13 P1116 14 P1117 15 P1120 16 P1121 17 P1122 18 P1123 19 P1124 20 P1125

How to repair an auto computer with Protech?

1 Send in your Auto Computer. 2 Your Repaired Auto Computer will be sent back to you. No Charge for Shipping. ProTech Autosystems can also reprogram your auto computer to fit your needs. We offer Free Shipping and Expert Care!

How to get a replacement computer for your car?

1 Order Your Auto Computer. 2 A Replacement Auto Computer will be sent to you. No Charge for Shipping. 1 Send in your Auto Computer. 2 Your Repaired Auto Computer will be sent back to you. No Charge for Shipping. ProTech Autosystems can also reprogram your auto computer to fit your needs.

Navigation