Why does my Mazda RX-8 engine not start?
At the time it sounded like the battery, because engine turned very slowly. Since, I’ve changed battery, checked all fuses, and engine still doesn’t start (though it engine turns fine). Would you please assist me with any info which will help me to determine what’s wrong.
What should I do if my Mazda RX-8 stall?
Try puting your car in neutral at the light – the vibration should stop or be barely noticeable. Mazda had a regional rep come out to look at my car, and his solution was to give me my 7th set of motor mounts. The vibration was a little better for about 10 feet, then it was back and worse than ever.
When to use full automatic on Mazda RX-8?
1) Don’t use the full automatic in city driving. 2) For 20MPH use only 1st gear. 3) For 35MPH use only 2nd. 4) For 45MPH use only 3rd gear.) If you are traveling highway speeds above 65MPH full automatic is OK.
How does a compression tester work on a Mazda RX 8?
A compression tester is connected to one of the spark plug holes and the engine is cranked until the tester reads a number in PSI. Rotary engines have 3 combustion surfaces per rotor so they require special compression testers to show each of the three faces.
At the time it sounded like the battery, because engine turned very slowly. Since, I’ve changed battery, checked all fuses, and engine still doesn’t start (though it engine turns fine). Would you please assist me with any info which will help me to determine what’s wrong.
Why is my Mazda RX-8 stalling and stalling?
You feel it in the brake pedal,steering wheel,doors, and you can see the vibration in the mirror’s.Dealer said that their scanner/computer show that everything is in the NORMAL RANGE LIMITS……. The motor mounts have been checked and show no signs of wear.
Why does my car make a grinding noise when I crank the starter?
Note that continually trying to crank a car with a damaged starter could cause additional damage to the starter (the flywheel will turn the starter too fast). If you hear a grinding noise when the key turns in the ignition, one of our certified mechanics can inspect and repair the problem.
1) Don’t use the full automatic in city driving. 2) For 20MPH use only 1st gear. 3) For 35MPH use only 2nd. 4) For 45MPH use only 3rd gear.) If you are traveling highway speeds above 65MPH full automatic is OK.
Is there a recall on a Mazda RX8?
If you have a problem with your ignition system, (no spark) that would not be covered. The recall is for warranty extension from, 5yrs 50K to 8yrs 100K, if the engine has lack of power, stalling, low compression and may not be related to your concern.
What to do if your Mazda RX-8 won’t start?
If the lights anywhere in your car are not turning on, your battery may be dead. Check to see if you can start your engine. If the engine turns on then your battery should be working properly. However, if the engine will not start, refer to the Car Cranks But Won’t Start .
When did the Mazda RX-8 come out?
This category covers 2004, 2005, 2006, 2007, 2008 Mazda RX-8 Troubleshooting models. Your guide to finding the problems with your Mazda RX-8 so you can effectively and efficiently resolve them.
Why does my Mazda RX-8 stall at 3000 rpm?
The rough idle appeared to go away after driving a long highway trip where RPM tended to remain above 3000 for long periods. I believe there are two things going on with the RX-8 AT. The engines simply need to run at least at 3000RPM to keep everything clean and clear.
Where does the oil go in a Mazda RX-8?
For help rotating tires please check out the Tire Rotation Guide. Engine oil in the RX-8 lubricates the moving parts of the engine, but is also injected into the rotary compression chambers to provide lubrication for the apex seals. As you drive the car the oil picks up impurities in the engine and can lose some of its lubricating properties.
What kind of car starts but wont stay running?
Many people have reported having similar failures such as “my 2000 BMW starts but won’t stay running” or “my car starts then die unless I give it gas.” This article is here to give solutions to complaints and answer all the questions related to these kinds of problems.
Why does my car run after I start it up?
One potential problem that could arise is the inability to control the fuel injection system correctly. This might cause problems keeping the car running after you start it up.
Why does my engine start but then stop?
A Bad Camshaft Position Sensor. A bad camshaft position (CMP) sensor can produce different types of symptoms and cause the engine to stall immediately after starting or intermittently. A bad camshaft sensor is likely to trigger the check engine light (CEL).
Why does my Mazda 3 stall at stops?
Something similar happened to me with my 2004 Mazda 3. At the end, the problem was the fuel pump. After disconnecting the battery to jump start another car, my car’s PCM could never re-learn how to control the engine because the fuel pressure was way below specifications.
Where to get a Mazda 3 car starts and then dies inspection?
Mazda 3 Car starts and then dies Inspection at your home or office. Our certified mobile mechanics come to you 7 days a week between 7 AM and 9 PM. Our certified mobile mechanics can come to you now. received a Car starts and then dies Inspection. Mazda 3 Car starts and then dies Inspection costs $85 on average.
Try puting your car in neutral at the light – the vibration should stop or be barely noticeable. Mazda had a regional rep come out to look at my car, and his solution was to give me my 7th set of motor mounts. The vibration was a little better for about 10 feet, then it was back and worse than ever.
Which is better Mazda crossfire or Mazda RX 8?
While the RX-8 is one of the purest sports cars on the road, the Crossfire is more of a GT car. Although it’s undeniably a fine car, I don’t think the Crossfire really compares to the RX-8 from a sporting point of view – plus, it doesn’t have a back seat.
Why is my Mazda RX 8 engine clogged?
Just as a clogged air filter will prevent the engine from sucking in air to combust, a clogged catalytic converter will prevent the engine from releasing the combusted exhaust. As a catalytic converter gets old it begins to clog.
What causes a car to start at the wrong time?
Spark plug wires are a source of electromagnetic interference (EMF), but this is usually only a problem on some aftermarket setups when this interference isn’t taken into account. A timing belt or chain that has skipped a tooth will throw off the cam timing, causing the intake and/or exhaust valves to open at the wrong time.
How to fix a Mazda that stalls at stop?
Remove the air hose from the throttle body. Disconnect the throttle body connector. Remove the throttle body from the intake manifold, with the water hose connected. Clean the throttle body on the air hose side using a soft, clean shop cloth, sprayed with engine cleaner (Mazda recommends their P/N 000-77-A86).
Spark plug wires are a source of electromagnetic interference (EMF), but this is usually only a problem on some aftermarket setups when this interference isn’t taken into account. A timing belt or chain that has skipped a tooth will throw off the cam timing, causing the intake and/or exhaust valves to open at the wrong time.
How do you start a Mazda RX-8 Renesis?
If you can’t, Mazda produced a quick guide on the appropriate starting and stopping procedures for the RX-8 Renesis which we’ve replicated below: Should the engine fail to start, please use the following procedure. With the ignition off, press the accelerator pedal to the floor and hold. Turn key to start the engine, keeping the pedal to the floor.
What’s the best way to stop a Mazda RX 8?
Stopping Procedure Should your Mazda RX-8 not reach normal operating temperature before the end of your journey, please use the following stopping procedure: With the engine running and transmission in neutral, increase engine revs to 4,000 rpm. Hold revs at 4,000 rpm for 10 seconds. Turn off the ignition while the engine is running at 4,000 rpm.
Is the Mazda RX-8 a dynamic car?
As dynamic as it can be. The Mazda RX-8 excels with an even weight distribution between all four wheels, which is key to realising its optimal driving dynamics. This distribution was realised by mounting the compact RENESIS rotary engine as low and as far back in the car as possible in a front-midship layout.
If you can’t, Mazda produced a quick guide on the appropriate starting and stopping procedures for the RX-8 Renesis which we’ve replicated below: Should the engine fail to start, please use the following procedure. With the ignition off, press the accelerator pedal to the floor and hold. Turn key to start the engine, keeping the pedal to the floor.
Stopping Procedure Should your Mazda RX-8 not reach normal operating temperature before the end of your journey, please use the following stopping procedure: With the engine running and transmission in neutral, increase engine revs to 4,000 rpm. Hold revs at 4,000 rpm for 10 seconds. Turn off the ignition while the engine is running at 4,000 rpm.
As dynamic as it can be. The Mazda RX-8 excels with an even weight distribution between all four wheels, which is key to realising its optimal driving dynamics. This distribution was realised by mounting the compact RENESIS rotary engine as low and as far back in the car as possible in a front-midship layout.
Why does my RX8 not start after a hot soak?
RX8 No Start & Hard to Start when Hot soak. This RX8 came into our shop for diagnosing no start when it is hot. When you drive for a while and turn off the engine, then if you try to restart after a short period, it refuses to restart (cranks ok). After at least fifteen minutes to half an a hour wait the car will start.
When did I buy my first Mazda RX8?
Come on you die hards out there…The first of you to buy this car had to be 3rd gen folks…I still own a 3rd Gen RX7, 1993 with 82,000 miles. I absolutely love the car and may never part with it, no matter how much time it spends in the shop, but my experiences with it being a first year car will probably cause me to wait until year 2 of the RX8.
Is the Mazda RX-8 a JDM car?
‘A Cool JDM Car’ or ‘Mazda… 2021 IMSA WeatherTech Sports… The place to discuss anything technical about the RX-8 that doesn’t fit into any of the categories below. Wanna save some coin or time/money in the shop?
What kind of engine does a Mazda RX8 have?
What Engine Does a Mazda Rx8 Have? The Mazda RX-8 receives power from the 1.3L RENESIS two-rotor rotary engine that creates 212 horsepower at 7,500 rpm as well as 159 pound-feet of torque at 5,500 rpm. With a manual transmission, the Mazda RX-8 rotary engine can create 232 horsepower at 8,500 rpm.
Why is my Mazda RX-8 engine not starting?
The RX-8 engine runs very rich when it is first started, meaning as it warms up it it has a higher then normal amount of fuel in the engine. Shutting off the car before it has a chance to warm up can flood the engine and leave it unable to start again.
How many miles does a Mazda RX8 engine last?
Generally speaking, the Mazda Rx8 engine can last about 60,000 miles. It is important to keep in mind to maintain your engine and make sure that you take your car into a mechanic when you have issues. What are some of the most common complaints About the Mazda Rx8 & the Engine?
Why is the oil in my Mazda RX-8 so dirty?
As you drive the car the oil picks up impurities in the engine and can lose some of its lubricating properties. Because in the RX-8 the oil is introduced inside the engine it is even more important that the engine oil remain clean and fresh.
How do you warm up a Mazda RX8 engine?
You need to warm up the engine slowly, stay in low revs depending on outside temperature for at least 20 minutes. Beware you need to warm up the oil, and the gauge on your dash is the water temperature, which heats up a lot faster! After that, drive it like you stole it.
While the RX-8 is one of the purest sports cars on the road, the Crossfire is more of a GT car. Although it’s undeniably a fine car, I don’t think the Crossfire really compares to the RX-8 from a sporting point of view – plus, it doesn’t have a back seat.
What kind of engine does Mazda RX-8 have?
Rear rotor – rotor tip seal failed with a tiny piece breaking away – about a 1mm deep. After much arguing with mazda UK they providea new engine but i had to pay an excessive amount to the stealers to put the engine in. 212-horsepower 1.3L R2 6-speed shiftable automatic RWD
A compression tester is connected to one of the spark plug holes and the engine is cranked until the tester reads a number in PSI. Rotary engines have 3 combustion surfaces per rotor so they require special compression testers to show each of the three faces.
Generally speaking, the Mazda Rx8 engine can last about 60,000 miles. It is important to keep in mind to maintain your engine and make sure that you take your car into a mechanic when you have issues. What are some of the most common complaints About the Mazda Rx8 & the Engine?
Are there any recalls on the Mazda RX 8?
In the following overview, you will find the most common problems for the Mazda RX-8, for which Mazda has announced a recall through the EU Rapex system. For recalls and faults found in the UK scroll down. If the problem is corrected in time, it may not affect the overall reliability of your Mazda RX-8.
If you have a problem with your ignition system, (no spark) that would not be covered. The recall is for warranty extension from, 5yrs 50K to 8yrs 100K, if the engine has lack of power, stalling, low compression and may not be related to your concern.
Is there an automatic version of the Mazda RX 8?
Automatic versions all had lower output/lower rpm engines due to the lack of availability of a transmission that would be able to reliably cope with the engine’s high rpm limits. In 2003 Mazda announced a factory Mazdaspeed Version of the RX-8 exclusively in Japan.
When did the Mazda RX 8 hydrogen car come out?
At the 2004 North American International Auto Show, Mazda unveiled the RX-8 Hydrogen RE concept car, designed to run on either hydrogen or gasoline.
Why does my Mazda RX-8 stall at lights?
My car also “stumbles” from time to time when I put it back in gear from neutral at a light. Try puting your car in neutral at the light – the vibration should stop or be barely noticeable. Mazda had a regional rep come out to look at my car, and his solution was to give me my 7th set of motor mounts.
Why is my Mazda RX 8 engine overheating?
As a catalytic converter gets old it begins to clog. This will keep the hot exhaust gasses in the engine, which along with decreasing power, also can lead to engine overheating.
Is it possible to flood a Mazda RX 8?
If you are a little careful, you will never flood. If you car is at normal operating temperature you will never flood. If you move the car a small amount let it idle for a minute or two rev the car to 5,000rpms and turn off the engine while it is revved to 5000. I have done this for 6 year and never flooded once.
Why does my 2004 Mazda RX 8 not start?
“Owner dropped 2004 Mazda RX-8 to the dealer to fix recall, driver and passenger air bag, voluntary emission recall, and also owner complains that the engine won’t start when the engine is hot, you have wait for about 30 minutes to cool down the engine before the engine starts again. Advisor asked the owner to have the engine diagnose.
Why does my RX8 start hot or cold?
As a matter of fact, cars with a rotary engine, the RX8 included, should start like any other motor vehicle, regardless of whether it is hot or cold. There are two common reasons why car owners are having such a problem. The first reason is that their car’s engine might be suffering from low compression.
What kind of problems does a RX8 have?
RX8 Common Issues. Hot start problems (signs of poor compression). Growling noise and loss of power (sticking SSV or tune valves). Engine Management Light flashing whilst driving (real time detection of engine misfire). Rattling Exhaust (catalyst damaged with ceramic in rear section of exhaust).
Why does my Mazda RX8 engine not start?
My Mazda RX8 will not start, it ran fine yesterday, but today it will not start. It turns over, but sounds different, like no compression or spark. I have heard of engine failures to this model year, but don’t know the symptoms.
How can I defloode my Mazda RX-8 engine?
There are several methods to deflood the engine ranging removing and drying the spark plugs, to taking it to a dealer. Keep in mind that continued cranking while the engine is flooded can drain the battery. This results in the possibility of a low battery preventing the car from starting even after the engine has been deflooded.
There are several methods to deflood the engine ranging removing and drying the spark plugs, to taking it to a dealer. Keep in mind that continued cranking while the engine is flooded can drain the battery. This results in the possibility of a low battery preventing the car from starting even after the engine has been deflooded.
RX8 No Start & Hard to Start when Hot soak. This RX8 came into our shop for diagnosing no start when it is hot. When you drive for a while and turn off the engine, then if you try to restart after a short period, it refuses to restart (cranks ok). After at least fifteen minutes to half an a hour wait the car will start.
Just removing the spark plugs will not resolve a flooded engine concern on this vehicle. The problem is that the engine has lost compression and will not fire. You can verify you ignition system is ok by checking for spark at the plug while a friend crank the engine.
Can you put ATF in a Mazda RX8?
Yes ATF works good. Yes, do not just start the engine and move car 20 feet and shut off. You need to get the engine warm or hold at 4-5K rpms before shutting off. I put oil in one intake port. could not get the cap off the rear one so I put oil in the lead spark plug holes as the manual said.
Why does my Mazda RX 8 engine not start?
There is no easily accessible fuel pressure regulator or fuel filter as both are built into the fuel pump assembly. Worst case scenario, if this engine cranks but won’t start it’s likely got bad compression and will require a rebuild, however if your lucky it might be something else.
If you are a little careful, you will never flood. If you car is at normal operating temperature you will never flood. If you move the car a small amount let it idle for a minute or two rev the car to 5,000rpms and turn off the engine while it is revved to 5000. I have done this for 6 year and never flooded once.
What causes a Mazda RX-8 engine to turn red?
As a catalytic converter gets old it begins to clog. This will keep the hot exhaust gasses in the engine, which along with decreasing power, also can lead to engine overheating. A failing catalytic converter can, but not necessarily, glow red after a hard drive.
What causes RX 7 twin turbo to hesitate at 3000 rpm?
3,000 RPM Hesitation Fix RX-7 twin turbo hesitation at 3000 RPMs. 3,000 RPM Hesitation Fix Last updated: May 3, 2003 There are several potential causes of and fixes for the hesitation that some people have experienced around 3,000 RPM: 3K Hesitation Survey Results(Read This First!) Grounding Battery Fuel Pump / Pressure
What Engine Does a Mazda Rx8 Have? The Mazda RX-8 receives power from the 1.3L RENESIS two-rotor rotary engine that creates 212 horsepower at 7,500 rpm as well as 159 pound-feet of torque at 5,500 rpm. With a manual transmission, the Mazda RX-8 rotary engine can create 232 horsepower at 8,500 rpm.
What makes the Mazda rotary engine one of the most useless?
With the Mazda’s rotary style engine, come a host of well-document problems. What makes the rotary engine one of the most useless engines out there? By design the Wankel engine as a low thermal efficiency. Part of this is due to the fact that they also have low compression ratios- with the poorly made shape of the combustion chamber.