Are there any recalls on the 2011 Mazda CX 9?
Based on information received from our latest subscriber survey, our reliability history charts give you a rundown on how used vehicles are holding up in 17 potential trouble spots, ranging from the engine, transmission, and brakes to power equipment and the electrical system. The 2011 Mazda CX-9 has been recalled 4 times by NHTSA. View Recalls
Is the Mazda CX 9 a good car?
As tested by Consumer Reports, the 2020 Mazda CX-9 performed as it should even during the braking test, an area of concern in previous years. However, the brake pedal is still firm and stopping distances were long for its class. Overall, the Mazda CX-9 is popular among its owners.
How much does it cost to repair a Mazda CX 9?
This issue earns the top spot due to collateral damage. Often, when a Mazda CX-9 water pump fails, it leaks coolant into the engine oil and causes engine failure too. On average this has occurred at 102,150 miles and has a typical repair cost of $3,990 for replacing the entire engine with a used one.
How do you reset the power window on a Mazda?
Here’s how to do the power window reset procedure. 1) Turn the ignition switch to the ON position. 2. Press the switch of each window and fully open the door glass. 3. Pull the switch of each window to the manual-up position to fully close the window and keep holding the switch up at the position for approx. 2 s.
Are there any problems with the Mazda CX-7?
The Mazda CX-7 definitely had its fair share of engine problems, and it all starts with the turbocharger. According to Consumer Reports, there is a long list of problems with the engine.
What makes a Mazda CX-9 a reliable car?
The Reliability score is based on our latest subscriber survey of 2011 Mazda CX-9 owners. The owner comments describe problems respondents experienced with this vehicle. Driveshaft or axle, CV joint, differential, transfer case, 4WD/AWD components, driveline vibration, traction control, electronic stability control (ESC), electrical failure.
How much does it cost to repair a Mazda CX-7?
Signs that the compressor is going out include loud noises, smoke, and in extreme cases, the serpentine belt actually catches on fire. While there are some problems that owners ignore, this is definitely not one that can be overlooked. The average repair cost to fix this is around $700.
Are there any issues with the Mazda CX-7?
The Mazda CX-7 from 2009 has almost no reported issues. However, drivers may still want to be wary of models from 2010 and 2011. The turbo engine failure is still an issue, though it was far less frequent than in 2007. Some cars from these two model years also had suspension problems.
Based on information received from our latest subscriber survey, our reliability history charts give you a rundown on how used vehicles are holding up in 17 potential trouble spots, ranging from the engine, transmission, and brakes to power equipment and the electrical system. The 2011 Mazda CX-9 has been recalled 4 times by NHTSA. View Recalls
When did the Mazda CX-9 have transmission problems?
Between 2007 and 2013 however some issues did crop up that tended to occur somewhere between 65000 and 70000 miles. The worst year for transmission problems in the Mazda CX-9 seem to be 2012. Again, we need to point out that when we say worst year, we don’t mean it was bad by any means.
The Reliability score is based on our latest subscriber survey of 2011 Mazda CX-9 owners. The owner comments describe problems respondents experienced with this vehicle. Driveshaft or axle, CV joint, differential, transfer case, 4WD/AWD components, driveline vibration, traction control, electronic stability control (ESC), electrical failure.
What kind of problems does a Mazda CX 9 have?
Driveshaft or axle, CV joint, differential, transfer case, 4WD/AWD components, driveline vibration, traction control, electronic stability control (ESC), electrical failure. “Became compromised prior to hitting 100,000 miles.
How to check the support rod on a Mazda?
Check under the bonnet area to make certain all filler caps are in place and all loose items (e.g. tools, oil containers, etc.) have been removed. Lift the bonnet, grasp the padded area on the support rod, and secure the support rod in the clip. Verify that the support rod is secured in the clip before closing the bonnet.
What to do when your Mazda car breaks down?
Grasp the support rod in the padded area and secure it in the support rod hole indicated by the arrow to hold the bonnet open. Check under the bonnet area to make certain all filler caps are in place and all loose items (e.g. tools, oil containers, etc.) have been removed.