What does code p0122 on a TPS mean?

Throttle Pedal Position Sensor/Switch (TPS) A Circuit Low Input What Does Code P0122 Mean? Code P0122 is triggered when your vehicle’s Engine Control Module (ECM) detects that your Throttle Position Sensor (TPS) circuit A is reporting an output voltage that is below its expected voltage.

How can I Check my TP sensor code?

With the scope, you can view the voltage signal as a wave form. This enables you to spot any fleeting problems. If the TPS checks out OK, but you still have P0122 code illuminated, you’ll need to check the sensor circuit. First, you want to disconnect the sensor connector and test for power and ground. You can do this using a digital multimeter.

What should the TPS sensor read at idle?

Typically, the sensor should read around 4.5 volts at wide open throttle and .45 volts with the throttle at the idle position. You can also test the TPS with a scan tool. Connect the scan tool to the diagnostic port, and scroll through the PID list until you find the TPS voltage or position PID.

What does trouble code 21 on throttle position sensor mean?

Trouble Code 21 indicates that the Throttle Position Sensor (TPS) is reading abnormally high. TPS volts should be close to 0.42 V at closed throttle and rise smoothly in about 0.02 volt increments to a maximum reading of about 4.85 volts at WOT. TPS signal voltage is greater than 4.3 volts Air Flow is less than 17 gm/sec.

What does trouble code 25 mean on a thermistor?

Trouble Code 25 indicates that the Manifold Air Temperature (MAT) or Intake Air Temperature (IAT) sensor is reading higher than expected. When the air is cold, the thermistor has a high resistance, which falls as the air charge warms. High readings thus indicate possible short circuits in MAT circuit.

What does the code p0122 on the ECM mean?

What Does Code P0122 Mean? Code P0122 is triggered when your vehicle’s Engine Control Module (ECM) detects that your Throttle Position Sensor (TPS) circuit A is reporting an output voltage that is below its expected voltage.

What does the OBD 2 fault code p0222 mean?

What Does Code P0222 Mean? OBD II fault code is defined as “Throttle/Pedal Position Sensor/Switch B Low Input”, and set when the PCM (Powertrain Control Module) detects a signal voltage from the TPS (Throttle Position Sensor) that does not correlate with the current engine speed.

What does code p0102 mean on a car?

When code P0102 is set, there is a low voltage output to the ECM, PCM, or ECU depending on your car type (check your owner’s manual for your specific car). Code P0102 does not pose any serious danger to the driver or the vehicle and there are no drivability issues that may occur.

How to diagnose Honda throttle position sensor p0122?

Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost to diagnose the P0122 HONDA code is 1.0 hour of labor.

What does the TPS sensor on a Honda Civic do?

An excessively low voltage from the Throttle Position Sensor (TPS) is sent to Engine Control Module (ECM). The Throttle Pedal Position (TPP) responds to the accelerator pedal movement. This sensor is a kind of potentiometer which transforms the throttle position into output voltage, and emits the voltage signal to the Engine Control Module ( ECM ).

What does p0122 mean on a TPS sensor?

A P0122 code means that the the vehicle’s computer has detected that the TPS (throttle position sensor) “A” is reporting too low a voltage.

How much does it cost to diagnose Honda code p0122?

The cost to diagnose the P0122 HONDA code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? When is the code detected?

What was the cause of the Volkswagen p0122 accident?

P0122 VOLKSWAGEN Possible Causes 1 Faulty throttle pedal position sensor 2 Throttle pedal position sensor harness is open or shorted 3 Throttle pedal position sensor circuit poor electrical connection

What are the codes for the OBD II?

Learn how to troubleshoot the following OBD II Codes: P0120, P0121, P0122, P0123 and P0124 which are related to the Throttle Position Sensor Circuit. The video also contains detailed instructions about how to test the TPS Sensor ( Throttle Position Sensor), using either an ohm meter, voltmeter or a hand held OBD II Scanner. Loading…

How can I fix the error code p0122?

To fix the error code P0122, you will need first to locate the position of the A circuit. You can find this information in your vehicle’s repair manual. Next, you will want to check the sensor for damage and look at the connections and wiring for any signs of breakage. Then, you will need to check the voltage of the sensor.

What is the diagnostic trouble code for Honda?

This diagnostic trouble code (DTC) is a generic powertrain code and applies to many OBD-II vehicles (1996-newer). That may include but is not limited to vehicles from Honda, Jeep, Toyota, VW, Chevy, Ford, etc.

When does the throttle position sensor display a low voltage?

Code P0122 gets logged when the throttle position sensor “A” displays lower voltage than normal. Several OBD-II trouble codes also cover the performance of the throttle position sensor at the “A” position. They are:

What does OBDII code p0122 mean on Dodge Ram?

P0122 is a common trouble code with the Dodge Ram. It’s an OBDII code that references issues with the Throttle Position Sensor (TPS). It is relatively serious problem since it can leave your vehicle stranded or severely limited. OBDII code P0122 is a serious problem that requires serious attention.

What does a code p0126 mean on a car?

A code P0126 may mean that one or more of the following has happened: Low engine coolant level Faulty thermostat Faulty coolant temperature sensor (CTS) CTS electrical wiring or connector problem – open, short, or poor connection

What does the coolant temperature code p0128 mean?

Code P0128 may trigger if the engine control module (ECM) determines that coolant temperature is lower than desired or does not increase quickly enough. What Does Code P0128 Mean?

What does a p0126 diagnostic trouble code mean?

What does that mean? A P0126 diagnostic trouble code (DTC) is a generic powertrain code. That means it applies to all makes/models from 1996-newer but specific troubleshooting steps may depend on the specific vehicle.

What should I do if I have a p0128 trouble code?

Your intake air temperature sensor, coolant temperature sensor and coolant fan could also signal this trouble code, so these should be inspected after you look over your thermostat and coolant level. Start with the easiest repair solution, which is low coolant levels.

What does p0128 mean on a Dodge thermostat?

Since this often indicates a problem with the thermostat, regardless if you are driving a Dodge, a Ford, or a Jeep, the P0128 code is likely to appear once your coolant thermostat or temperature sensor fails. Of course, as was mentioned earlier, there are other potential causes for the code, as well.

Why does my car have trouble code p0125?

For most vehicles, trouble code P0125 is related to this issue as well. Your thermostat is an essential component for regulating coolant temperature and checking for more serious issues with your engine. However, a damaged thermostat won’t typically cause any performance issues.

What causes p0122 Ford OBD2 engine light codes?

P0122 FORD Possible Causes 1 Faulty throttle position sensor. 2 Throttle position sensor harness is open or shorted 3 Throttle position sensor circuit poor electrical connection More …

How much does it cost to repair a p0122 Ford engine?

Check for damaged components and look for broken, bent, pushed out, or corroded connector’s pins. The cost of diagnosing the P0122 FORD code is 1.0 hour of labor. The auto repair labor rates vary widely across the country, and even within the same city. Most auto repairs shops charge between $75 and $150 per hour.

How much does it cost to diagnose p0122 Ford engine code?

The cost to diagnose the P0122 FORD code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour. How much do you know about cars? When is the code detected?

How to check Ford OBD2 engine trouble code?

Navigation