How to install a rear shock absorber on a Mazda CX 5?
1. Remove in the order indicated in the table. 2. Install in the reverse order of removal. (See Rear Shock Absorber Upper nut Installation Note.) 1. Lift up the rear lower arm using a jack and install the rear shock absorber upper nuts. 1. Remove the rear shock absorber.. 2. Inspect for damage and oil leakage. 3.
How do you replace a rear shock absorber?
1. Lift up the rear lower arm using a jack and install the rear shock absorber upper nuts. 1. Remove the rear shock absorber.. 2. Inspect for damage and oil leakage. 3. Compress and extend the shock piston at least three times. Verify that the operational force does not change and tha 1. Remove the rear stabilizer control link.. 2.
How often should I change my shock absorbers?
It is a good practice to replace the shock absorbers every 35,000 miles. You can easily find out if you need new shocks by doing a bounce test. Go to the rear corner of your car and push down on the rear of the car. If your car bounces up and down a few times, it is time to change the shock absorbers.
Why does my Mazda CX-5 radio keep coming on?
If you leave the car like this and shut the door it will NOT eventually shut off… it will drain your battery! Most people work around this by starting and stopping the car again but putting it in park forcefully… some times it takes several tries.
What are the shocks on a Mazda CX 5?
Mazda CX-5 2014, Strut-Mate™ Rear Shock Boot by Monroe®. The boot is designed to protect the strut piston rod from stones, mud, water, sand, and other abrasives providing longer service life for the strut. In addition, the included… Mazda CX-5 2014, Front Strut Mount by Beck Arnley®.
How tall are the springs on a Mazda CX 5?
Mazda CX-5 AWD 2014, Sport Front and Rear Lowering Coil Springs with 1.25″ Front and 1.75″ Rear Drop Height by H&R®. Quantity: 4 per Pack.
What kind of boot does a Mazda CX-5 have?
Mazda CX-5 2014, Strut-Mate™ Rear Shock Boot by Monroe®. The boot is designed to protect the strut piston rod from stones, mud, water, sand, and other abrasives providing longer service life for the strut. In addition, the included… Mazda CX-5 2014, Front Shock/Strut Bellow Kit by KYB®.
1. Lift up the rear lower arm using a jack and install the rear shock absorber upper nuts. 1. Remove the rear shock absorber.. 2. Inspect for damage and oil leakage. 3. Compress and extend the shock piston at least three times. Verify that the operational force does not change and tha 1. Remove the rear stabilizer control link.. 2.
How to install a steering knuckle on a Mazda CX 5?
Install the steering knuckle to the front shock absorber, insert the bolts from the direction shown as follows, then tighten them to the specified torque. Vehicle right side: Insert the bolts from the vehicle front. Vehicle left side: Insert the bolts from the vehicle rear. Locknut Installation Note 1.
How to repair the front wheel on a Mazda CX 5?
1. Disconnect the front ABS wheel-speed sensor.. 2. Remove in the order indicated in the table. 3. Install in the reverse order of removal. 4. After installation, inspect the front wheel alignment and adjust it if necessary.. 1 ABS wheel-speed sensor 2 Brake hose clip 3 Locknut (See Locknut Removal Note.) (See Locknut Installation Note.) 4
How to install a locknut on a Mazda CX-5?
1. Install the steering knuckle to the front shock absorber, insert the bolts from the direction shown as follows, then tighten them to the specified torque. Vehicle right side: Insert the bolts from the vehicle front. Vehicle left side: Insert the bolts from the vehicle rear. Locknut Installation Note 1.