Why does my Mazda 3 crank but not start?

Why does my Mazda 3 crank but not start?

Not sure if this is relevant or not. After doing a routine oil change in my garage, the engine will crank (pulleys and belts rotate), but it does not start. I called AAA, they showed up and immediately hooked up a battery booster.

What causes a car to turn over but not start?

Sometimes a plugged fuel filter or a problem with the fuel injectors can prevent the engine from getting any gasoline. To check this remove the air cleaner and smell inside the throttle body or air cleaner housing.

Why does my car engine not want to start?

If the engine still doesn’t seem like it wants to start, probably fuel is getting into the cylinders and your problems lies somewhere else. However, if the engine runs momentarily and dies, then the problem is that fuel is not getting to the cylinders. Check for a clogged fuel filter, or a bad fuel pressure regulator.

Why are there spark plugs in my Mazda 3?

Took out the spark plugs, then rotated the crankshaft pulley and I could see the camshaft rotate, so that meant to me the timing chain is still in one piece and at least partially functional. Next put a screwdriver into spark plug hole #1 and set the crankshaft pulley to its timing mark.

What to do if your Mazda3 won’t start?

One way to do this is to start your car and let the engine run for a while to recharge the battery. One thing to know: if the battery is over 4-5 years old, it may be completely dead, so it will not recharge and the car will not restart after you turn it off. In this case, you may need a new battery.

Why does my Mazda MPV engine not start?

Strong crank but no start. Often will start after awhile. Had to tow it and it stared right up after the car was dropped at the shop. Thought it was the fuel pump but mechanic said it was distributor. Another mechanic suggested a sticky air valve that causes important sensor to misread conditions.

What should I do if my engine won’t start?

If the engine cranks but won’t start, the fault may be internal to the distributor. Diagnosis will show no spark and trouble codes for the crankshaft position sensor (CKP) or the camshaft position sensor (CMP). Our technicians recommend replacement of the complete distributor assembly if these conditions occur.

How much does a Mazda no start cost?

The average cost for a Mazda MPV No Start Diagnosis is between $88 -$111. Learn More The van was running great and all of a sudden it will crank but will not start.

Not sure if this is relevant or not. After doing a routine oil change in my garage, the engine will crank (pulleys and belts rotate), but it does not start. I called AAA, they showed up and immediately hooked up a battery booster.

What’s the problem with my 2010 Mazda3?

No idea if it’s the alarm/immobilizer, battery, or something else. It’s a 2010 Mazda3. I’m hoping to avoid towing it to the Mazda dealership, although at this rate, it looks like I might have to. -Car wouldn’t start; it cranked, but wouldn’t catch.

Took out the spark plugs, then rotated the crankshaft pulley and I could see the camshaft rotate, so that meant to me the timing chain is still in one piece and at least partially functional. Next put a screwdriver into spark plug hole #1 and set the crankshaft pulley to its timing mark.

Why are the blinking lights on my Mazda3 not working?

It has enough charge to keep those blinking light and radio on but not enough for everything. The blinking lights will still work, the radio and such will still work. As you noticed once you turned on the headlight with the radio on, it turned off. Sure sign of battery issue.

How to fix a Mazda that stalls at stop?

Remove the air hose from the throttle body. Disconnect the throttle body connector. Remove the throttle body from the intake manifold, with the water hose connected. Clean the throttle body on the air hose side using a soft, clean shop cloth, sprayed with engine cleaner (Mazda recommends their P/N 000-77-A86).

What does a Mazda 3 engine sound like?

He (AAA guy) said the engine sounds like a sawing machine and the timing chain is gone. So I took off the oil filler cap and looked inside with a flash light so that I can see the cam closest to the firewall/driver.

How to fix a Mazda CX 7 turbo problem?

Visit https://www.lemonlaw.com/lemon-law-firm.html to find one in your state. After a lot of leg work Mazda replaced mine. Not to crazy about having a rebuilt but i figured it cant be any worse than the original one. It took 3 weeks to get it back but seems to more power.

Are there any problems with the Mazda Turbo?

Many are having repeat failures with their Mazda turbocharger being replaced numerous times. Others are reporting oil consumption problems and severe engine noise.

Are there any problems with the Mazda CX 9?

According to the calls coming in, Mazda CX 7 and CX 9 drivers appear to be having turbo (turbocharger) and engine problems, and to make matters even worse, the manufacturer is trying to point the finger back at the consumer.

Is there a warranty on a Mazda CX 7?

Even when under warranty, Mazda dealers are asking consumers to present all oil change and service receipts prior to service to confirm they are maintaining the vehicle according to warranty prior to fixing any Mazda turbocharger problem. Failure to produce proof of service could result in Mazda denying warranty coverage.

Why does my Mazda 2 burn so much oil?

Most cars with the oil burning problem are 2004-2005 production cars. There is no clear answer to the question what causes high oil consumption. But Mazda has made some changes in the last years of production which made 2.3L engines less prone to the oil burning. In the rest, the engine is quite reliable and durable.

What kind of engine does a Mazda 3 have?

It is a member of the Mazda’s L-series. It was first introduced in 2003 model year of the Mazda3. This engine also has different later versions – LF-VE and LF-VD. The LF-DE has a high-grade aluminum alloy cylinder block with cast iron sleeves.

Why does my Mazda 2.0L LF-VE engine not warm up?

Bad connecting rod bearings also cause oil consumption. The engine has problems with thermostat often at 60,000 miles. The engine does not warm up or on the contrary, overheats due to a stuck thermostat. Cars with the LF-VE had some issues with acceleration and Check Engine sign.

What kind of engine is in a Mazda?

The Mazda L3-VE engine is a member of the Mazda’s L-series. It is 2.3-liter inline 4-cylinder gasoline engine that produced from 2001 to 2010. The L3-VE is also called as MZR engine. The engine is based on smaller 2.0-liter version – the LF-DE engine.

Most cars with the oil burning problem are 2004-2005 production cars. There is no clear answer to the question what causes high oil consumption. But Mazda has made some changes in the last years of production which made 2.3L engines less prone to the oil burning. In the rest, the engine is quite reliable and durable.

He (AAA guy) said the engine sounds like a sawing machine and the timing chain is gone. So I took off the oil filler cap and looked inside with a flash light so that I can see the cam closest to the firewall/driver.

Why does my motorcycle not start when I turn it on?

Clogged Injector Symptoms of a clogged injector: Your motorcycle will attempt to turn over normally when you try to start it but there won’t be any combustion. If you know it’s sparking correctly and that there is gas in the tank but it has been sitting for a while, your culprit is probably a clogged fuel injector.

What to do when your car wont start?

Next put a screwdriver into spark plug hole #1 and set the crankshaft pulley to its timing mark. The screwdriver was at its highest point so I figured the timing is correct.

Why is my Mazda 3 engine not starting?

There are a lot of issues that can cause your 3 to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code. It is definitely worth it to use an OBDII scanner to check and see if the engine has thrown any trouble codes.

What causes a car to crank but not start?

One of the biggest issues that causes a vehicle to crank but not start is ignition issues. When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc….. Ignition issues can be caused by many things, including bad spark plugs, bad coil packs, bad plug wires, computer issues, and more.

Why does my Acura TLX engine not start?

When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc….. Ignition issues can be caused by many things, including bad spark plugs, bad coil packs, bad plug wires, computer issues, and more. 3. Engine Timing

What to do if your fuel pump won’t turn over?

Replaced fuel pump turns over like new but won’t start fu… Replaced fuel pump new engine but still won’t turn over what else could it be My car has 157000 miles. My car has an automatic transmission. Of course, confirm that the engine immobilizer system (security system) is not activated thus preventing the car from starting.

Why does my Nissan Altima not start up?

Check for adequate fuel pressure, injector operation, and a spark at the spark plugs. Basically, if the starter motor is turning the engine over rapidly, at sufficient RPM, but the engine does not catch and run, that means that there is an ignition, fuel, air induction, or mechanical fault in the engine that will have to be repaired.

Why does my Mazda 3 not start up?

When your Mazda 3 won’t start, the problem is related to the battery, the starter, the fuel system, the ignition, the engine’s timing, or the security. Dealing with starting issues can be very frustrating, especially if you’re driving your beloved Mazda 3.

Replaced fuel pump turns over like new but won’t start fu… Replaced fuel pump new engine but still won’t turn over what else could it be My car has 157000 miles. My car has an automatic transmission. Of course, confirm that the engine immobilizer system (security system) is not activated thus preventing the car from starting.

Check for adequate fuel pressure, injector operation, and a spark at the spark plugs. Basically, if the starter motor is turning the engine over rapidly, at sufficient RPM, but the engine does not catch and run, that means that there is an ignition, fuel, air induction, or mechanical fault in the engine that will have to be repaired.

What causes a fuel pump to not ignite?

If there is fresh fuel being delivered by the injectors (not just “to” the injectors) and the ignition system is working, that means that the air fuel ratio of the mixture delivered to the cylinders is so far off that the mixture just won’t ignite.

What kind of oil is in Mazda 3 boots?

There was no residue, just a brown color. #1 and #4 boots had uniform grey color throughout. The #4 spark plug had oil and gunk on the white part outside the cylinder, and a lot of (what looked like fresh) oil on the thread. I smelled it because of the flooding suspicion, but could not smell gasoline. It might have been oil mixed with gasoline?

Why is my Mazda CX7 not starting properly?

Then they installed a new high pressure fuel pump (I guess the CX7 has two fuel pumps). Finally, after 10 days it seemed like the problem was rectified. However one day later the problem reoccurred. They tell me it is the high pressure fuel pump again.

Can a Mazda CX 7 be shipped to the military?

PLUS, and here is the real kicker, Mazda will not ship to military overseas, nor will they honor warranty to military overseas (contrary to what the dealer says, they’ll say anything won’t they?). Wouldn’t have bought a Mazda if I had known.

What does the PCM do on a Mazda?

by Ashley Hay. The powertrain control module (PCM), or engine control unit (ECU), is a circuit board computer that stores information pertaining to different areas of your Mazda’s engine. If your Mazda’s check engine light or another malfunction indicator light illuminates, it is because of a signal the PCM received.

Why does my Mazda check engine light illuminate?

If your Mazda’s check engine light or another malfunction indicator light illuminates, it is because of a signal the PCM received. The PCM will trigger the indicator light to illuminate to inform you there may be an issue with your Mazda.

Can you reconnect the negative terminal clam on a Mazda?

Reconnect the “Negative” terminal clam on your Mazda’s battery. Based in Columbus, Ga., Ashley Hay has been covering animal health and wellness since 2004, and arts and entertainment since 2008. She holds a Bachelors of Arts in psychology from the University of Central Florida.

Why does my Mazda 3 not want to start?

You’re getting oil on your spark plug; replace the valve cover gasket, it isn’t very hard, basic tools are needed, and a valve cover gasket kit from a dealership and some gasket maker silicon. It could just be a severe enough leak going through #4 to not want to start.

Why does my Mazda Protege crank but not start?

It could be the valve timing, spark plug, fuel injection, or ignition timing. If not then it may also be a clog in the fuel line if you let it sit on a downward slope for a few days. Mine was clogged when I was on vacation and mine would crank but would not start.

by Ashley Hay. The powertrain control module (PCM), or engine control unit (ECU), is a circuit board computer that stores information pertaining to different areas of your Mazda’s engine. If your Mazda’s check engine light or another malfunction indicator light illuminates, it is because of a signal the PCM received.

If your Mazda’s check engine light or another malfunction indicator light illuminates, it is because of a signal the PCM received. The PCM will trigger the indicator light to illuminate to inform you there may be an issue with your Mazda.

How can I tell if my Mazda 6 has no spark?

You have no spark did you check to see if the fuel pump activates when you switch on the ignition ,should activate for 2 seconds and activate again when you crank the engine . I did check for codes and it is giving a P0335 code. I checked wires leading to the sensor and also just replaced the sensor to be 100% sure. Still no spark.

What to do when your engine has no spark?

Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. Finally, Have someone crank the engine and watch for spark. Remove one of the coils from the spark plug. Use an extra spark plug. A spark plug tester. Or even a screwdriver in the end of the coil.

Why does my Mazda RX8 engine not start?

My Mazda RX8 will not start, it ran fine yesterday, but today it will not start. It turns over, but sounds different, like no compression or spark. I have heard of engine failures to this model year, but don’t know the symptoms.

You have no spark did you check to see if the fuel pump activates when you switch on the ignition ,should activate for 2 seconds and activate again when you crank the engine . I did check for codes and it is giving a P0335 code. I checked wires leading to the sensor and also just replaced the sensor to be 100% sure. Still no spark.

What to do if your car cranks but won’t start?

If the engine cranks but won’t start, the fault may be internal to the distributor. Diagnosis will show no spark and trouble codes for the crankshaft position sensor (CKP) or the camshaft position sensor (CMP). Our technicians recommend replacement of the complete distributor assembly if these conditions occur. Ready to sell?

How to tell if your neutral switch is bad?

Symptoms of a Bad or Failing Neutral Safety Switch 1 Engine will not crank in park but cranks in neutral. 2 Engine will not crank in neutral but cranks in park. 3 Engine does not crank at all, regardless of the transmission gear. 4 Engine cranks in any gear.

Why does my Car Crank but not start?

Check The System Security System Security is a probable reason making a car cranks but won’t start. At times, the system security gets confused because of a procedural error. If security system flashes when starting the engine, exit the vehicle and lock all the doors and windows to good 20 minutes.

What happens when you put the car in neutral?

1. Engine will not crank in park but cranks in neutral. When the driver turns the ignition switch and the automatic transmission is in park, or the manual transmission is in neutral and the clutch pedal is engaged, the car should trigger the starter to engage.

Symptoms of a Bad or Failing Neutral Safety Switch 1 Engine will not crank in park but cranks in neutral. 2 Engine will not crank in neutral but cranks in park. 3 Engine does not crank at all, regardless of the transmission gear. 4 Engine cranks in any gear.

Is it safe to start a car in neutral?

If the gear is on this position, it would be easy and safe to start the vehicle. Yet there are some signs that will pinpoint defect on this part. One is when the lever has to be shifted from park or neutral mode in order to get the engine to start. Another, which you are encountering, is if the car starts in Neutral but not in Park mode.

Why does my Mazda 6 have no start?

In extremely cold weather (approximately -30° C), a customer may experience an engine no-start/no-crank condition due to a frozen main relay and/or fuel pump relay. Due to the design, moisture can enter the relays and freeze the contact points after driving a short distance, and this may shut off the engine, resulting in the no-start state.

What kind of engine does a Mazda 3i have?

I have a 2005 Mazda 3i 2.0L 5 speed manual. I bought it back in April with 92,000 miles and it now has 110,000 miles. It has a catback straight pipe exhaust and the previous owner said the engine was swapped, due to a timing chain failure on the previous one.

Why is my Mazda 3 cranking but not starting?

It really can get that one last start out of it. There are a lot of issues that can cause your 3 to crank, but not start. The engine needs air, fuel, and a spark in order to run. It is highly likely that if the engine is cranking, but not starting that it has thrown an OBDII code.

Why does my Mazda RX 8 engine not start?

There is no easily accessible fuel pressure regulator or fuel filter as both are built into the fuel pump assembly. Worst case scenario, if this engine cranks but won’t start it’s likely got bad compression and will require a rebuild, however if your lucky it might be something else.

Why does my Mazda Protege make no noise?

Does it start when you try jumping it. It can also be a bad starter although this will normally have a clicking noise or no noise instead of a cranking noise. It could be the valve timing, spark plug, fuel injection, or ignition timing. If not then it may also be a clog in the fuel line if you let it sit on a downward slope for a few days.

What are common reasons my Mazda B3000 wont start?

What are common reasons my Mazda B3000 won’t start? While there are a variety of reasons your Mazda B3000 won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter. How is a no-start diagnosis fixed?

What to do when your Mazda Truck wont start?

When my truck wont start, I will shoot a little starter fluid into the air intake and about 99% of the time it will fire up. I pull out the hose that goes from your valve cover to your air intake between the air filter and manifold. Its the easiest place to do it. You can also open your air filter housing and spray it in there.

Is there a problem with my Mazda B4000?

I have a Mazda B4000 and I am having problems with it starting. About two weeks ago it would not crank, then after a couple of days it cranked again. It has been doing fine for the last week.

What kind of spark does a Mazda 3 have?

I check the spark by taking out all the spark plugs, then holding one after the other against the metal block and checking for spark while someone turned the ignition. All 4 plugs showed spark, and they looked strong with a bluish spark color.

Why are the cranks on my MX5 not working?

My mx5 cranks but engine does not start, mechanic suggested to replace the camshaft sensor, but still no luck still the same crank but does not start, the funny think about it after 36-48 hours the car starts no problem and then it dies after one working day and it goes back to crank no start till I leave it for a good few hours.

Why is my MX5 still trying to catch fire?

Go to pick it up and it does the whole crank/fire/die thing. Towed it home in the end and it hasn’t started yet. It is getting fuel (pulled hose off and cranked…fuel everywhere) and it is still TRYING to fire (so it’s not the cambelt or petrol pump.)

Insert a spark plug tester into the plug boot and ground it on a piece of metal on the engine. Finally, Have someone crank the engine and watch for spark. Remove one of the coils from the spark plug. Use an extra spark plug. A spark plug tester. Or even a screwdriver in the end of the coil.

Why does my Mazda 6 not start up?

Mazda 6 2004 cranks but wont start. Loses spark after first rotation. We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.

What kind of engine does a Mazda 6 have?

Mazda6 2004 cranks but won’t start. Looses spark after first rotation. Experience: ASE Technician advanced level specialist. Wisconsin certified emissions state inspector Hello! What size engine do you have? Are there any codes in the computer? Does the check engine light come on with the key on?

Why does Mazda 6 I 2.3L engine not start?

Otherwise you have already done all the testing possible to prove that the entire vehicle is operating properly and the only possible cause is a faulty PCM. All Mazda service manual no start diagnosis step have a final test that says if all other test prove out ok then the next step is to replace the PCM.

How to swap Mazda 2.3L to 2.5L?

Then take pretty much everything off the 2.3 and bolt it to the 2.5 long block. Mazda oil pickup, oil pan, timing cover, intake cam shaft, intake manifold, camshaft position sensor, heater hose connector block thing, and all Mazda wiring.

Is there a problem with my Mazda 6i?

Mazda 6i: “04 MAZDA 6 i 2.3L Engine. No-Start. No Codes.”Yo… “04 MAZDA 6 i 2.3L… “04 MAZDA 6 i 2.3L Engine. No-Start. No Codes.” You may recall working this problem about three years ago, but there was no conclusion to this post and I am having the very same problem with a 2003 same vehicle.

I have a 2005 Mazda 3i 2.0L 5 speed manual. I bought it back in April with 92,000 miles and it now has 110,000 miles. It has a catback straight pipe exhaust and the previous owner said the engine was swapped, due to a timing chain failure on the previous one.

Does it start when you try jumping it. It can also be a bad starter although this will normally have a clicking noise or no noise instead of a cranking noise. It could be the valve timing, spark plug, fuel injection, or ignition timing. If not then it may also be a clog in the fuel line if you let it sit on a downward slope for a few days.

What to do if your 2004 Mazda6 won’t start?

No one has added a helpful site for this 2004 MAZDA6 problem yet. Be the first! Read reviews of repair shops in your area. Enter your zip code:

Why does my car not start when I crank the engine?

If the engine doesn’t crank, or makes an unusual noise when cranking, you may have a starting system problem. The car’s security system may have made an error that disabled the fuel or ignition system, or the chip in the key may have failed.

Mazda 6 2004 cranks but wont start. Loses spark after first rotation. We use cookies to give you the best possible experience on our website. By continuing to use this site you consent to the use of cookies on your device as described in our cookie policy unless you have disabled them.

Next put a screwdriver into spark plug hole #1 and set the crankshaft pulley to its timing mark. The screwdriver was at its highest point so I figured the timing is correct.

Why does my Mazda 3 stall at stops?

Something similar happened to me with my 2004 Mazda 3. At the end, the problem was the fuel pump. After disconnecting the battery to jump start another car, my car’s PCM could never re-learn how to control the engine because the fuel pressure was way below specifications.

What to do when your engine stalls at a stop?

Start the vehicle and let idle until engine is warm, and then shut it back off. Wait 10-15 minutes then start the vehicle, let idle until warm & then shut back off.

Can a Mazda MX5 turn over but not fire?

Mazda mx5 will not start, turns over but will not fire, have changed air flow sensor & camshaft sensor, electrician has used a diagnostic machine but no faults showing, he is leaning towards an immobiliser fault, any advice? Clicking this will make more experts see the question and we will remind you when it gets answered.

Why does my Mazda CX 5 won’t start?

While there are a variety of reasons your Mazda CX-5 won’t start, the most common 3 are a dead battery, an alternator problem, or failed starter. How is a no-start diagnosis fixed? Correcting most no-start problems usually involves replacing the alternator, starter or battery, cleaning connections, ignition system repairs, or fuel system repairs.

What happens when you push the start button on a Mazda?

(SKYACTIV-G 1.5, MZR 1.6, SKYACTIV-G 2.0, SKYACTIV-G 2.5) After pressing the push button start and before the engine starts, the operation sound of the fuel pump motor from near the fuel tank can be heard, however, this does not indicate a malfunction.

What’s the best way to start a Mazda?

The engine starts by pressing the push button start while depressing the clutch pedal (manual transaxle) or the brake pedal (automatic transaxle). To switch the ignition position, press the push button start without depressing the pedal.

What does it mean when your Mazda 6 won’t start?

This just means that the engine doesn’t move when you turn the key. The second way that your 6 won’t start is when the engine turns when you engage the starter, but it won’t fire and run on its own. When the engine isn’t turning over at all, that’s a bit easier to diagnose than when it is cranking but not firing.

One of the biggest issues that causes a vehicle to crank but not start is ignition issues. When there is no spark, the engine will not start. You’ll probably have a misfire related code such as P0300, P0301, etc….. Ignition issues can be caused by many things, including bad spark plugs, bad coil packs, bad plug wires, computer issues, and more. 3.

Can a blown head gasket cause a no start?

Although rare, internal engine mechanical problems can and do cause no-start conditions (especially after severe overheating or running the engine with no oil). Blown head gasket. Blown engine. By now, you might be thinking that a no-start condition may be too difficult to diagnose but nothing could be further from the truth.

What to do if your Mazda RX-8 won’t start?

If the lights anywhere in your car are not turning on, your battery may be dead. Check to see if you can start your engine. If the engine turns on then your battery should be working properly. However, if the engine will not start, refer to the Car Cranks But Won’t Start .

What to do if your Mazda RX8 won’t start?

You have flooded the engine if you go too you fuse box and take out the fuel pump fuse turn the engine over for a while this gets rid of the fuel left in the cups in the engine replace the fuse try it again it will start You can’t post conmments that contain an email address.

What causes a car to start but not keep running?

The engine requires the right amount of air and fuel to mix together for ignition. If there is a fuel leak somewhere, then the correct amount of fuel may not make it to the combustion chamber. This might be enough to allow the engine to start, but not keep running.

Can a bad crankshaft sensor cause the engine to stall?

If the crankshaft position sensor or its wiring have any issues, it can cause the crankshaft signal to be cut off while the engine is running, which can cause the engine to stall. This is usually a symptom of a wiring problem, however a bad crankshaft position sensor can also produce this symptom.

What causes a car to stall on a cold start?

It also manages the idle under changing engine loads, like when you kick on the air conditioning, turn on the headlights, or turn up the radio. When the idle air control valve malfunctions, you may experience a rough idle or the vehicle may stall entirely. This is especially true on cold starts.

What should I do if my car wont start?

When the security light goes off, turn the ignition off, wait 20 seconds, and then start the engine. These are the most popular ways to solve the problem of anti theft system car wont start.

If the engine cranks but won’t start, the fault may be internal to the distributor. Diagnosis will show no spark and trouble codes for the crankshaft position sensor (CKP) or the camshaft position sensor (CMP). Our technicians recommend replacement of the complete distributor assembly if these conditions occur. Ready to sell?

There is no easily accessible fuel pressure regulator or fuel filter as both are built into the fuel pump assembly. Worst case scenario, if this engine cranks but won’t start it’s likely got bad compression and will require a rebuild, however if your lucky it might be something else.

What does it mean when your engine won’t start?

Problem Description. If the engine cranks but won’t start, the fault may be internal to the distributor. Diagnosis will show no spark and trouble codes for the crankshaft position sensor (CKP) or the camshaft position sensor (CMP). Our technicians recommend replacement of the complete distributor assembly if these conditions occur.

Can a car start with a faulty immobilizer?

Unfortunately, if the key is faulty or there is a problem with the immobilizer, your car will not start; it is an electronic safety system that prevents the vehicle from cranking without the presence of the original ignition key.

Why does my immobilizer light flash when I Turn Off the starter?

There were two things that caused this. One: when Best Buy installed the remote starter last year they crack an internal antenna in the immobilizer module. And two: one of the wires leading to the starter was corroded and allowed current to flow sporadicly. The red key light always is supposed to flash when the car is off and the key is removed.

How to solve the anti theft system car wont start?

It is another way to solve the problem of anti theft system car wont start. Disconnect the positive terminal of the battery for a minute or two. Reconnect it and make sure that both the anode and cathode terminals are tightly attached. It will reset the computer system and your car is likely to kick off.

Unfortunately, if the key is faulty or there is a problem with the immobilizer, your car will not start; it is an electronic safety system that prevents the vehicle from cranking without the presence of the original ignition key.

What kind of engine does a 2002 protege es Mt have?

What year is the car and what engine did you put into it (from what year?) The car is a 2002 Protege ES MT, the motor is from a 2001 Protege with an AT, but the tranny shouldnt matter, I swapped flex plates and the crankshaft pulley. They were both FS-DE motors.

What year is the car and what engine did you put into it (from what year?) The car is a 2002 Protege ES MT, the motor is from a 2001 Protege with an AT, but the tranny shouldnt matter, I swapped flex plates and the crankshaft pulley. They were both FS-DE motors.

Is there a problem with my Mazda 3?

To present myself a little bit, im from a northern region of Quebec in Canada and im an owner of a Mazda 3 2008 with only 91 000 km. Im going to explain you the problem as detailed as possible. This problem is intermittent…

What to do if your car won’t start?

4. If NOTHING changed after 1.-3. and car battery still loses charge, then recharge car battery again to 100% and then open car fuse box and look which car circuit LEAKS electricity or is SHORT. Read car manual for fuse box circuit descriptions.

Why does my car not start if the battery is OK?

If the battery is OK, but the starter still won’t start, there could be a number of possible reasons. Here are a few: The ignition switch could be faulty – this is a common problem.

Where is the ignition switch on a Mazda 3?

An ignition switch is an electrical switch installed on the rear of the ignition lock mechanism. If shaking the key in the ignition switch helps to start the car, you should check the ignition switch first. The starter solenoid control wire may have a bad connection.

Is it illegal to leave your engine running while parked?

It is not illegal to leave engine running while parked or on public highway,provided the driver is in the car.! It is only illegal if the engine is left running unattended. Also,have some sympathy and respect for your engine and starting system, no machine or any appliance likes to be stopped and started. You will use more fuel and more wear on …

What should I do if my Mazda MPV won’t start?

Our technicians recommend replacement of the complete distributor assembly if these conditions occur. The average cost for a Mazda MPV No Start Diagnosis is between $88 -$111. Learn More The van was running great and all of a sudden it will crank but will not start.

Remove the air hose from the throttle body. Disconnect the throttle body connector. Remove the throttle body from the intake manifold, with the water hose connected. Clean the throttle body on the air hose side using a soft, clean shop cloth, sprayed with engine cleaner (Mazda recommends their P/N 000-77-A86).