How to replace driver door module and passenger door?

Position the door module in the hole on the door panel. Check that the lower mounting for the door module is correctly located in the support on the door panel Press the door module into place Connect the connectors Install the nut and screw Install the door panel.

How do you remove a door control module?

Pull the door module backwards and upwards. Remove the door module from its mounting on the door panel Press up the door module. To remove the upper panel, see Removing the upper panel. Page 1 of 4 Check Check that the control module connectors are intact. Installing the control module

Where is the door module located on a car?

This method of installation applies to both the driver door module (DDM) and the passenger door module (PDM). Position the door module in the hole on the door panel.

Why is my driver side door not working?

My drivers side controls on the door will not work. You can not roll down window, the door does not lock and you can not asdjust mirrors. If you try the passeng … read more

What to do if your driver side door has lost power?

My driver side door has lost power completely, no mirror control or windows, lock or anything. The remote doesn’t work My driver side door has lost power completely, no mirror control… Vocational, Technical or Tra… all of the controls on the drivers door have stopped working. Vocational, Technical or Tra… I have a 2003 Chevy Suburban 1500.

What kind of car door has lost power?

2003 suburban, front passenger door has lost power to all electrically devices (window, lock, and mirror). In addition, the remote control will not lock … read more Vocational, Technical or Tra…

Why is my passenger window not working but the driver window is working?

When passenger windows don’t work, but the driver’s window does, chances are high that you’ve got a bad master switch in the driver’s door or a broken wire in the driver’s door hinge area. Second: Power window motors only have two wires.

What to do if your passenger door actuator is not working?

Start your search on the side that is operating incorrectly. If the HVAC is stuck in one mode, get access to the top higher actuator on the passenger side (see location above) to see if it is functioning correctly. But remember to reset the fuse first (also above) and see if that does the trick. Diagnosing a faulty actuator is pretty easy.

What is the actuator on the passenger side?

Diagnosing a faulty actuator is pretty easy. Again, the driver’s actuator and the lower actuator on the passenger side control heat/cool only to the drive and passenger respectively. The higher actuator on the passenger side controls the defrost/dash/floor settings.

Where is the electric motor on a window?

A window motor is a reversible electric motor powered by a switch. It is usually installed inside the door panel behind the trim. By pressing the window switch, an electric current is sent to the window motor.

What kind of motor do I need for bus passenger door?

Electric door motor for bus electric passenger door. Motor fits most bi-fold electric passenger doors in shuttle buses. 12v door motor with a 12 point gear. If your bus door needs a motor, this should be the one. A&M Systems door motor. Cross reference numbers ; 1068; 6092-ECC; 21252144; P100047; 113260; 13260; 800-171.

What is kit number for bus passenger door?

Kit # K9129, module number AT-CSR-048. We sell more than bus passenger door circuit boards. While you’re here, you should check your bus to see if any lights need to be replaced. We have a great selection of exterior and interior lights for shuttle buses. A&M EMERGENCY RELEASE LEVER.

Can a front passenger door be unlocked with a key?

Usually in cars with manual door locks, only the driver and front passenger doors could be locked or unlocked from the outside with a key. Meanwhile, the locks in the rear passenger doors can only be engaged or disengaged by pushing down or pulling up the button, knob, or pin on the interior side of the car door.

Are there any controls on the passenger door?

Passenger door controls have always worked as you would expect with the door open or closed.

This method of installation applies to both the driver door module (DDM) and the passenger door module (PDM). Position the door module in the hole on the door panel.

How does door control work on a DVD drive?

In comparison with similar software, Door Control uses a special algorithm to recognize whether the doors are open or closed. A single click is enough to open or close the DVD drive door. The user may customize the color of the button, assign a hotkey and launch the software at system start-up.

Can you replace the drivers side door harness?

Some research on the internet pointed to the drivers door wiring harness. Sure enough, replaced the harness and all the problems went away. Not a hard job to replace but a million screws to take out, make sure to watch a video or look at a diagram to be able to find all the little buggers.

Is there a free door control repair guide?

Access our free Door Control Module Schematics Repair Guide for Avalanche, Sierra, Silverado, C&K Series, 1999-2005 through AutoZone Rewards. These diagrams include: Access our Avalanche, Sierra, Silverado, C&K Series, 1999-2005 Door Control Module Schematics Repair Guide by creating an account or signing into your AutoZone Rewards account.

Navigation