What does the code p0161 stand for?
Code P0161 stands for HO2S heater Performance Bank 2 Sensor 2. This indicates the PCM has detected a problem with heater circuit of the downstream oxygen sensor. Bank 2 refers to the side of the engine opposite the #1 cylinder.
Can a faulty oxygen sensor trigger a p0141 code?
If your vehicle only has four cylinders, it will only have one bank and, typically, one downstream sensor, so it can’t trigger this code. Instead, a faulty downstream heated oxygen sensor will be set as P0141 or Oxygen Sensor Heater Circuit Malfunction (Bank 1, Sensor 2).
What does the DTC code p0141 stand for?
DTC P0141 stands for “Oxygen Sensor Heater Circuit Malfunction (Bank 1, Sensor 2).” It indicates a problem with the heater circuit of engine bank 1’s downstream O2 sensor. Make sure you know bank 1 from bank 2 before you start clearing any of the codes.
What does p0161 mean on ho2s Bank 2?
Code P0161 stands for HO2S heater Performance Bank 2 Sensor 2. This indicates the PCM has detected a problem with heater circuit of the downstream oxygen sensor. Bank 2 refers to the side of the engine opposite the #1 cylinder. If you’ve got a four-cylinder, there will only be one bank, and you would not get this code.
Code P0161 stands for HO2S heater Performance Bank 2 Sensor 2. This indicates the PCM has detected a problem with heater circuit of the downstream oxygen sensor. Bank 2 refers to the side of the engine opposite the #1 cylinder.
Code P0161 stands for HO2S heater Performance Bank 2 Sensor 2. This indicates the PCM has detected a problem with heater circuit of the downstream oxygen sensor. Bank 2 refers to the side of the engine opposite the #1 cylinder. If you’ve got a four-cylinder, there will only be one bank, and you would not get this code.
Why is my O2 sensor code po161?
I replace my O2 sen cause I was having PO161 CODE after replacing my O2 sensor the CEL turned-off. 20 miles later PO141 and PO161 came back on. Any idea what is going? I order a replacement O2 SEN part thinking it’s defective.
What does p0161 mean on a ho2s heater?
P0161 is a diagnostic trouble code (DTC) for “HO2S Heater Circuit Malfunction (Bank 2 Sensor 2)”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
How much does it cost to repair a p0161 BMW?
The cost of diagnosing the P0161 BMW code is 1.0 hour of labor. The auto repair’s diagnosis time and labor rates vary by location, vehicle’s make and model, and even your engine type.
What is code p0138 and p0607?
P0138 is for the O2 sensor. Either shorted or open. P0607 is for ECM problem. Most likely the O2 is the main cause of the problem and the code for a bad ECM is thown in just in case raplacing the O2 sensor or checking the wire harness do not fix the problem.
What do codes p1132 and P1152 mean?
DTCs P1132 bank 1 (Cylinder 1) and P1152 bank 2 indicate the fuel/air ratio is correcting lean for an overly rich condition. The HO2S voltage is greater than 0.45 volt. DTC P1130 and P1150 indicate the fuel control system has reached maximum compensation for a lean or rich condition and the HO2S is not switching.
What does engine code p0160 mean?
What the P0160 code means. This code means that the powertrain control module has detected a fault in the circuit for the oxygen sensor for bank 2 sensor 2. The Check Engine Light will illuminate to let the owner know that there is a problem with the emissions system.
What does code p013c mean?
OBD-II Code P013C is defined as a O2 Sensor Slow Response – Rich to Lean. The purpose of the oxygen sensor is to measure the oxygen content in the exhaust gases after they leave the combustion process of the engine. The engine control module (PCM) is constantly adjusting the amount of fuel delivered to the engine based off of the oxygen sensor’s signal.