How to replace the hub and bearing on a Lexus ES300?
To remove and replace the hub-and-bearing assembly, you need to remove the rear brake caliper assembly and brake rotor. This article with video details the steps involved in replacing the rear wheel hub and bearing on a 1999 Lexus ES300.
What causes a loose wheel bearing on a Lexus?
Loose steering is often caused by a loose wheel hub bearing. Here’s a step-by-step guide to replacing it. This article applies to the Lexus (2005-2013).
What causes rear wheel hub bearing to wear out?
Out-of-balance rear tires may cause this problem by wearing out the rear wheel hub bearing. On most Toyota and Lexus passenger vehicles, the rear wheel hub and bearing are integrated as one component and fastened to the rear wheel knuckle with four (4) bolts.
How to replace a wheel hub on a Lexus?
Remove each of the four bolts, one by one, spinning the position of the wheel hub to align the hole with each bolt in turn. Use a magnetized wand to ease removal of each bolt. 3. Remove the wheel hub. Note that the upper hub mounting points are wider than the lower mounting points. 4.
Loose steering is often caused by a loose wheel hub bearing. Here’s a step-by-step guide to replacing it. This article applies to the Lexus (2005-2013).
Where is the axle nut on a Lexus?
The axle nut is on the axle with a lot of torque. Make sure the impact gun you’re using is fully charged or connected to a full air compressor. Figure 8. Remove the axle nut. Remove the two upper 22mm bolts completely from shock absorber. Using a pry bar, pry the steering knuckle off of assembly.
How do you replace a wheel on a Lexus?
Loosen lug nuts on the wheel. Raise the car using a jack and secure the vehicle with jack stands. Figure 2. Raise and secure the vehicle. Once you have the wheel off, you can begin to remove the brake caliper and the disc brake. Figure 3. Remove brake components.
Where are the shock absorber bolts on a Lexus?
Using a 22mm socket, loosen but do not remove the upper shock absorber bolts located under the hood on top of the wheel well. Figure 7. Loosen the upper shock absorber bolts. The axle nut is on the axle with a lot of torque. Make sure the impact gun you’re using is fully charged or connected to a full air compressor.
How to replace the rear brake bearing on a Lexus?
Here are the steps you need to take to perform the replacement yourself. 1. Unbolt the rear brake line from the rear suspension strut. 2. Remove the two (2) bolts that secure the rear brake caliper bracket (with the pads and caliper attached). 3. Pull the rear brake caliper assembly off of the rear brake rotor. 4. Remove the rear brake rotor.
To remove and replace the hub-and-bearing assembly, you need to remove the rear brake caliper assembly and brake rotor. This article with video details the steps involved in replacing the rear wheel hub and bearing on a 1999 Lexus ES300.
Remove each of the four bolts, one by one, spinning the position of the wheel hub to align the hole with each bolt in turn. Use a magnetized wand to ease removal of each bolt. 3. Remove the wheel hub. Note that the upper hub mounting points are wider than the lower mounting points. 4.
Out-of-balance rear tires may cause this problem by wearing out the rear wheel hub bearing. On most Toyota and Lexus passenger vehicles, the rear wheel hub and bearing are integrated as one component and fastened to the rear wheel knuckle with four (4) bolts.
Here are the steps you need to take to perform the replacement yourself. 1. Unbolt the rear brake line from the rear suspension strut. 2. Remove the two (2) bolts that secure the rear brake caliper bracket (with the pads and caliper attached). 3. Pull the rear brake caliper assembly off of the rear brake rotor. 4. Remove the rear brake rotor.
What causes a Lexus steering wheel to loose?
Loose steering is often caused by a loose wheel hub bearing. Here’s a step-by-step guide to replacing it. This article applies to the Lexus (2005-2013). If you ever feel a little play or wiggle room in your Lexus’ steering wheel, you probably have a bad wheel hub bearing.
How do you replace a wheel hub bearing?
Pry the steering knuckle off. Take the hub assembly and new bearing to a machine shop. They will use a special service tool to “press” the bearing and race into place. Once this is done, installation of all components is reverse of removal. Refer to the links below for proper torque procedures. Figure 10. Take the hub assembly to an auto shop.
Loose steering is often caused by a loose wheel hub bearing. Here’s a step-by-step guide to replacing it. This article applies to the Lexus (2005-2013). If you ever feel a little play or wiggle room in your Lexus’ steering wheel, you probably have a bad wheel hub bearing.