Can I use my V-6 transmission on a V8?

v8 swap is very easy, the stock v6 tranny will work but it won’t hold up as well as the v8 tranny, and get the v8 computer and wire in the extra 2 injectors into the wiring harness and your set.

Is a 4.6 Mustang a V-6 or V8?

The Ford 4.6L engine is a naturally aspirated V8 from Ford Motor was used to power a variety of different vehicles like sports cars, pickup trucks, sport utility vehicles, luxury sedans and cargo vans. The first vehicle to be powered by this engine was the Lincoln Town Car in 1990.

Can you switch out a V6 engine to a V8?

There are at least a dozen different companies that make V6-to-V8 conversion kits that include motor mounts, exhaust headers and sometimes a transmission mount. These kits give you the parts you’ll need to physically fit the engine into the truck, but you’re going to have to supply everything else.

What kind of transmission does a 1999 Mustang have?

1999-Early 2001 Mustang GT 4.6L 2V SOHC V8 Equipped with Code-6 Transmission 1999-Early 2001 Cobra 4.6L 4V DOHC V8 Equipped with Code-6 Transmission Early 2001 Mustang Bullitt 4.6L 2V SOHC V8 Equipped with Code-6 Transmission

What kind of transmission does a T45 Mustang have?

Gear ratios for the T45 are: 1996-1998 Ford Mustang GT 4.6L 2V V8 1996-1998 Ford Mustang Cobra 4.6L 4V V8 1999-early 2001 Ford Mustang GT 4.6L 2V V8 with transmission code 6 1999/early 2001 Ford Mustang Cobra 4.6L 2V V8 with transmission code 6 early 2001 Ford Mustang Bullitt 4.6L 2V V8 with transmission code 6

How big is the transmission shaft on a Mustang?

There are three lengths of Mustang input shafts. 83-93 V-8, 94-04 V-6 /94-95 V-8, 4-cyl. The 4-cyl shaft is about a quarter inch longer than the 83-93 V-8 shaft. The difference is considered negligible, but the pilot bearings are also different sizes. The 94-04 input shaft is about 11/16 longer than the 83-93 V-8.

Can a T5 transmission be used on a 302 Mustang?

To upgrade to a T5 (which is plentiful and cheap) you will need to change the flywheel (if upgrading to larger clutch only which you should), bellhousing, and speedo gear (The SROD may have a reverse speedo gear like 60’s Fords). NOTE: The factory bellhousing for your 302/SROD can be used for transmissions like Tremec 3550, TKO, etc…

What kind of transmission do I need for a Ford Mustang?

The most common transmission swap with older Fords is from a C4, C6, or FMX to an AOD or manual 5-speed. The focus here is putting a Ford AOD into a classic Mustang and other vintage Ford applications, which are the more common swaps.

Can a 4 cylinder transmission be swapped in a 83-93 Mustang?

While the 4-cylinder shaft cannot be swapped, a 4-cylinder transmission can be put into an 83-93 Mustang with the right pilot bearing (Do you really want to do this?) The Pilot Diameter of the Input Shaft The V-8 pilots are 0.668 and the 4-cyl pilots are 0.590 inches.

Can a 3.8 T 5 work on a 5.0 Mustang?

The 3.8 T-5 will work fine, its strong enough for your low mod 5.0. You must use a 94-95 5.0 T-5 bellhousing, 5.0 shim plate, and 5.0 157-t 50oz flywheel. Gotta remember that the flywheel must fit the bellhousing and vice versa, this also affects the starter motor. Use 5.0 10.5″ clutch. 3.8 or 94-95 clutch arm will work.

Navigation