What are the trouble codes for Kia OBD-II?
Kia Specific Trouble Codes Code Description P1115 Engine Coolant Temperature Signal from E P1121 Throttle Position Sensor Signal Malfunct P1170 Front Heated Oxygen Sensor Stuck. P1195 EGR Pressure Sensor (1.6L) or Boost Sens
Where to find check engine light code on Kia?
When retrieving Kia check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
Why is the oxygen sensor on my Kia not working?
Oxygen Sensor Circuit Slow Response – Bank 1 Sensor 2. Oxygen Sensor Circuit No Activity detected – Bank 1 Sensor 2. Oxygen Sensor Heater Circuit Malfunction – Bank 1 Sensor 2. Fuel Trim Malfunction – Bank 1. System too Lean – Bank 1. System too Rich – Bank 1. Injector Circuit Low – Cyl.
What is the trouble code on a 1995 Kia Sportage?
TEST and ground terminals. On 1995 Sportage models, turn ignition to On, but do not start engine. On other models, start and warm engine, then run at 2,000 RPM for 3 minutes. Diagnostic trouble codes will be displayed as a series of long and short flashes on the malfunction indicator lamp (MIL).
When retrieving Kia check engine light codes with an OBD II scan tool, proceed as follows: 1. Connect scan tool to the 16-pin data link connector (DLC) located underneath the steering column. The connector may have a removable cover. 2. Turn the ignition on. 3.
How to test Acura check engine light codes?
Next, read our article Automotive Circuit Testing 101, and if there is an article related to the system you are testing, such as Oxygen Sensors or EGR concerns, read these as well. They will provide valuable info! If there is a link to a specific diagnosis strategy for the code then follow that and start testing.
What is the code for Kia Rio LX 2011?
[attachment=0]Screenshot_20210218-234635.png [/attachment]Kia Rio LX 2011. Got this P0708 code for the Transmission Range Sensor or the Inhibitor Switch Sensor come on.
[attachment=0]Screenshot_20210218-234635.png [/attachment]Kia Rio LX 2011. Got this P0708 code for the Transmission Range Sensor or the Inhibitor Switch Sensor come on.
What causes an incorrect O2 sensor reading on a car?
There are also some other possibilities such as an internally leaking EGR system, (but this will typically set a separate code). A leak in the exhaust system before the O2 sensor will also cause incorrect readings. And always check for after- market modifications.
Where is the diagnostic connector on a Kia engine?
Scan Tool for Codes and Live Data for your Kia Engine from $149.95 Kia Engines – Please select the connector for your vehicle from the options below. This connector is usually located under the driver side dash panel. Locations: Left-hand side of firewall. Near or in the fuse box, or near the battery.
TEST and ground terminals. On 1995 Sportage models, turn ignition to On, but do not start engine. On other models, start and warm engine, then run at 2,000 RPM for 3 minutes. Diagnostic trouble codes will be displayed as a series of long and short flashes on the malfunction indicator lamp (MIL).
Oxygen Sensor Circuit Slow Response – Bank 1 Sensor 2. Oxygen Sensor Circuit No Activity detected – Bank 1 Sensor 2. Oxygen Sensor Heater Circuit Malfunction – Bank 1 Sensor 2. Fuel Trim Malfunction – Bank 1. System too Lean – Bank 1. System too Rich – Bank 1. Injector Circuit Low – Cyl.
Why do I have a p0302 code on my OBD II?
The reason for a code P0302 being stored in your OBD II vehicle is that the powertrain control module (PCM) has detected an individual cylinder misfire. A P0302 specifically applies to the number 2 cylinder. Consult a reliable vehicle information source for the location of the number 2 cylinder for the vehicle in question.
What does an OBD code for cylinder 2 mean?
P0302 Cylinder 2 Misfire Detected 1 OBD-II Trouble Code Technical Description. What does that mean? 2 Code Severity. Conditions which promote storage of a P0302 are likely to cause catalytic converter and/or engine damage. 3 Code Symptoms 4 Causes 5 Diagnosis & Repair Steps. …
What does trouble code p0734 OBD-2 mean?
A P0734 trouble code indicates that an abnormality has been detected in the gear ration of one of the automatic transmissions gears, causing the storage of a code in the Powertrain Control Module (PCM) and illumination of the Check Engine Light.
A P0734 trouble code indicates that an abnormality has been detected in the gear ration of one of the automatic transmissions gears, causing the storage of a code in the Powertrain Control Module (PCM) and illumination of the Check Engine Light.
What does trouble code p0302 mean on cylinder 2?
If the P0302 trouble code returns, an inspection of the cylinder 2 compression system will be done (this is not common). If the P0302 trouble code is still unresolved, a problem with the powertrain control module is possible (this is not common).
Why is there a trouble code on my cylinder 2?
This type of code is usually an indication that the car needs a tune up, so replacing one spark plug will normally not resolve the problem. In order to make a quick determination about whether a faulty wire or coil pack is causing the misfiring problem, switch the wires or coil pack for cylinder 2 with another cylinder’s wires or coil packs.