How to remove the ECM from a Kia Sedona?
1. Turn ignition switch OFF and disconnect the negative (-) battery terminal. 2. Remove the battery. 3. Remove the air cleaner assembly and intake air hose. 4. 5. Remove the ECM bracket assembly (B) after loosening the mounting bolts and nuts. 6. After removing the mounting nuts (A), remove the ECM from the bracket. 1.
What’s the best way to remove bolts from a Sedona?
Use a flat washer against the bolt head on one side and the lock washer and nut on the other side. Tighten the bolts and nuts with the impact gun, swivel and a socket while holding the bolt heads with a hand wrench. Remove the debris below the Sedona and lower it down to the floor.
How do you cut a converter on a Sedona?
Place the Sedona on a car lift and bring the vehicle all the way up on the lift. Put on the cutting glasses and light the oxyacetylene torch. Cut the two bolts on the front converter flange with the torch. Cut the bolts flush to the flange on the converter side. Cut the two bolts on the rear converter flange in the same manner.
How to change the VIN on a Kia Sedona?
1. Select “VIN Writing” function in “Vehicle S/W Management”. 2. Select “Write VIN” in “ID Resister”. 3. Enter the VIN. Before entering the VIN, double-check the VIN as it cannot be changed once programmed. 4. Turn the ignition switch OFF, then back ON.
How to turn off the ECM on Kia Sportage?
After finishing “ECM Neutral Mode”, turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically. Turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically.
What should I do if my ECM is broken?
RE-TEST THE ORIGINAL ECM: Install the original ECM (may be broken) into a known-good vehicle and check the vehicle. If the problem occurs again, replace the original ECM with a new one. If problem does not occur, this is intermittent problem.
1. Turn ignition switch OFF and disconnect the negative (-) battery terminal. 2. Remove the battery. 3. Remove the air cleaner assembly and intake air hose. 4. 5. Remove the ECM bracket assembly (B) after loosening the mounting bolts and nuts. 6. After removing the mounting nuts (A), remove the ECM from the bracket. 1.
1. Select “VIN Writing” function in “Vehicle S/W Management”. 2. Select “Write VIN” in “ID Resister”. 3. Enter the VIN. Before entering the VIN, double-check the VIN as it cannot be changed once programmed. 4. Turn the ignition switch OFF, then back ON.
After finishing “ECM Neutral Mode”, turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically. Turn IGN ON then OFF using the smart key or start button. Then the ECM learns information on the smart key automatically.
RE-TEST THE ORIGINAL ECM: Install the original ECM (may be broken) into a known-good vehicle and check the vehicle. If the problem occurs again, replace the original ECM with a new one. If problem does not occur, this is intermittent problem.
How to repair a Kia Sedona engine control module?
1. Install in the reverse order of removal. 1. TEST ECM GROUND CIRCUIT: Measure resistance between ECM and chassis ground using the backside of ECM harness connector as ECM side check point. If the problem is found, repair it.
Is there a problem with the Kia Sedona ECM?
If problem is not found in Step 1 and 2, the ECM could be faulty. If so, replace the ECM with a new one, and then check the vehicle again. If the vehicle operates normally then the problem was likely with the ECM.
What are the components of a Kia Sedona?
1. Engine Control Module (ECM) 2. Barometric Pressure Sensor (BPS) 3. Manifold Absolute Pressure Sensor (MAPS) 4. Intake Air Temperature Sensor (IATS) 5. Engine Coolant Temperature Sensor (ECTS) 6. Throttle Position Sensor (TPS) [integrated into ETC Module] 7. Crankshaft Position Sensor (CKPS) 8. Camshaft Position Sensor (CMPS) [Bank 1 / Intake]
Is the Kia ECM a plug and play unit?
Our Kia PCM, Kia ECM and Kia ECU units that are labeled plug & play will not require any additional programming. All of our control units are OEM, meaning you will get your vehicles original module.