Why is the blower motor on my 2007 rabbit not working?
If blower motor works on full speed then it is the resistor which is under the glove box on 2007 rabbit. Video on YouTube available. I have same issue, fuses are fine, fan does not work at all, have pulled blower and applied power- it works.
Why is my heater blower motor not working?
My heater blower motor is not working. The fuse is fine, and no it doesn’t work on high. This leads me to believe that it is not the relay?
Why is my blower motor on my Tiguan not working?
I had the same problem on my 2013 Tiguan and couldn’t find any solutions. I put an electric heater in the passenger footwell to heat the motor and after about 45 minutes, turned the vehicle on and it worked again. The same problem occurred about 3 times this winter.
Where are the wires on a Volkswagen blower motor?
Two underneath on both lower corners. Two are visible in the upper corners when you open up the glovebox door. There’s a fifth one inside on the back wall of the glovebox. Slide the glove box out slowly – you’ll need to unplug the wires to the light .
What to do if your blower motor stops working?
Have the key on and the fan switch on and bump the motor with you hand. It is the unit with the quick disconnect wire going to it on the right side closet to the wheel well.I took mine out today and cleaned it with spray cleaner for electric motors (NON-FLAMMABLE) and put it back in. There are only three 8 mm bolts holding it in place.
Why did the blower motor on my Dodge Ram stop working?
2007 Dodge Ram 1500, blower motor stopped working after running heater off and on while idle for several hours. Changed resistor, still not blowing heat. Any suggestions? Clicking this will make more experts see the question and we will remind you when it gets answered.
What causes a bad or failing blower motor relay?
Blown fuses. One of the first symptoms of a bad or failing AC blower motor relay is a blown AC blower motor relay circuit fuse. If the blower motor relay develops any sort of problem that hinders its ability to properly limit and distribute power, it may cause the blower motor fuse to blow. Any sort of electrical spikes or excessive current…
Why is my blower motor on my Ranger not working?
I recently experienced a problem where the blower motor in my 1996 Ranger quit working. When working with your blower motor you have to first understand that the blower basically works in the opposite manner of most automotive electrical components. Normally you switch on a positive current to an electrical component to turn it on.
If blower motor works on full speed then it is the resistor which is under the glove box on 2007 rabbit. Video on YouTube available. I have same issue, fuses are fine, fan does not work at all, have pulled blower and applied power- it works.
Why is the blower motor not working on my car?
My car has an automatic transmission. Hi There, The resistor is what controls the speed of the blower motor, not the relay. The blower motor relay supplies power to this motor when you turn the switch to “on” that can sometimes fail. When this happens, you may notice that you will not feel anything blowing out of the vents at all.
Why is the resistor not working on my blower?
Hi There, The resistor is what controls the speed of the blower motor, not the relay. The blower motor relay supplies power to this motor when you turn the switch to “on” that can sometimes fail. When this happens, you may notice that you will not feel anything blowing out of the vents at all.
How is the speed of the blower motor controlled?
The blower resistor is connected in series to the blower fan motor. This means that the current running through the blower motor, and its’ speed is therefore controlled by the resistor value. The user chooses a fan speed by selecting a speed which then connects one of the resistors in the blower resistor pack.
What should I do if my Bentley Blower Motor is not working?
You say you’ve checked the fuse and replaced the resistor. Wiring rarely breaks, so the next logical step is to access the fan motor per instructions in the Bentley service manual and use a multimeter to check for power at the fan motor connector when the switch is on.
Why does my AC / heater blower not work?
My radio, windshield wipers and ac/heater fan will not work. It will however work when you turn the key all the way back or forward but not when the engine is running. Not sure if it is a fuse problem or not. It is a 2003 and has 176,xxx miles on it. It’s not a fuse problem. You probably have a bad ignition switch.
Why is the air conditioning on my Volkswagen Rabbit not working?
What are common reasons my Volkswagen Rabbit has air conditioning problems? While there are a variety of reasons your Volkswagen Rabbit air conditioning won’t work, the most common 3 are a refrigerant leak, an electrical climate control issue, or a problem with the air conditioning compressor.
Why is my Volkswagen blower motor not working?
I put an electric heater in the passenger footwell to heat the motor and after about 45 minutes, turned the vehicle on and it worked again. The same problem occurred about 3 times this winter.
Is it illegal to replace refrigerant in a VW Rabbit?
Depending on location, it may be illegal for a technician to replace refrigerant without updating the A/C system to handle the newest type. Find the most common driver-reported problems that are to blame when a Volkswagen Rabbit has air conditioning problems.
Why are the wipers, heater, and headlights not working?
One day, I’ll turn the car on, and the wipers, blower, and turn signals do not work. Sometimes I drive for 15 minutes, and they all come on. Sometimes they don’t. Every time I’ve taken the car in for service the problem goes away before I get to the dealer, and they tell me they can’t do anything about it if they can’t replicate the problem.
Where are the Torx screws on a VW blower?
There are 5 torx screws. Two underneath on both lower corners. Two are visible in the upper corners when you open up the glovebox door. There’s a fifth one inside on the back wall of the glovebox. Slide the glove box out slowly – you’ll need to unplug the wires to the light .