How do you remove parking brake cable from Kia Sportage?
Loosen the parking brake cable bracket bolts and remove the parking brake cable. 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the rear tire and wheel. 3. Remove the rear brake caliper and Rear disc brake. 4. Remove the parking brake cable (B), after removing the clip (A).
What’s the average speed of a Kia Sportage?
Hand type – While operating the arking brake pedal for 68.6N (7kgf, 15.4 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph ( 18.6 mph). Foot type – While operating the parking brake lever for 147N (15kgf, 33 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph ( 18.6 mph).
Why do you need to replace your brake pads?
Brake pads are the most often replaced part of the brake system. This is because they are the part that makes contact with the rotor, and the resulting friction slows your vehicle down and allows you to stop. The pads also often include shims and abutment clips to prevent brake noise and ensure consistent, smooth, and even braking.
What should I do if my parking brake is replaced?
If the parking brake shoe or the brake disc are replaced a newly one, perform the brake shoe bed-in procedure. Hand type – While operating the parking brake pedal for 68.6N (7kgf, 15.4 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph (18.6 mph).
Loosen the parking brake cable bracket bolts and remove the parking brake cable. 1. Raise the vehicle, and make sure it is securely supported. 2. Remove the rear tire and wheel. 3. Remove the rear brake caliper and Rear disc brake. 4. Remove the parking brake cable (B), after removing the clip (A).
What should I do if my Kia Sportage has a problem?
The fix isn’t a ‘part’ problem, rather a software glitch that requires a hard reset. A hard reset can be a do-it-yourself fix at home, so usually, no costly trips to the dealership or mechanic’s shop. Instead, disconnecting and reconnecting the battery for a period of 15 minutes or so should do the trick.
Why does my Kia Sportage have no sound?
The cabins fall eerily quiet as no sound comes from the radio, phone connectivity, navigation, or CD players. The fix isn’t a ‘part’ problem, rather a software glitch that requires a hard reset. A hard reset can be a do-it-yourself fix at home, so usually, no costly trips to the dealership or mechanic’s shop.
Hand type – While operating the arking brake pedal for 68.6N (7kgf, 15.4 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph ( 18.6 mph). Foot type – While operating the parking brake lever for 147N (15kgf, 33 lbf) effort, drive the vehicle 500 meters (0.31 miles) at the speed of 30kph ( 18.6 mph).
The fix isn’t a ‘part’ problem, rather a software glitch that requires a hard reset. A hard reset can be a do-it-yourself fix at home, so usually, no costly trips to the dealership or mechanic’s shop. Instead, disconnecting and reconnecting the battery for a period of 15 minutes or so should do the trick.
Where is the clutch bracket on a Kia Sportage?
On the front of the gearbox, detach the clutch pipe bracket and the slave cylinder assembly. The clutch pipe remains connected to the slave cylinder, which should be stowed away to allow for easy gearbox removal. Next, undo the lower starter motor bolt.
The cabins fall eerily quiet as no sound comes from the radio, phone connectivity, navigation, or CD players. The fix isn’t a ‘part’ problem, rather a software glitch that requires a hard reset. A hard reset can be a do-it-yourself fix at home, so usually, no costly trips to the dealership or mechanic’s shop.
How do you remove a parking brake switch?
1. Remove the crash pad lower panel and reinforcement panel. (Refer to the Body group-crash pad) 2. Remove the junction box. (Refer to the Body Electrical System group – Fuses and Relays) 3. Disconnect the parking brake switch connector (A).
How to install parking brake on Kia Sportage?
6. Install the rear brake disc, then adjust the rear brake shoe clearance. Remove the plug from the disc. Rotate the toothed wheel of adjuster by a screw driver until the disc is not moving, and then return it by 3 notches in the opposite direction. 7. Install the brake caliper. (Refer to “Rear brake installation”) 8. Install the tire and wheel.
Where are the drum brakes on a Kia?
Many Kia vehicles have drum brakes on the rear wheels. While drum brakes are generally less effective than disc brakes, they have the advantage of being lighter and less expensive. It is also easy to incorporate the parking brake into a drum brake, eliminating the need for a separate parking brake mechanism.
What’s the best way to remove a brake drum?
Use a screwdriver to attach the brake drum puller’s screw tightly. Tighten the screw until the brake drum puller is securely fastened around the brake drum. Do not over-tighten the screw on the brake drum puller. Knock the back of the brake drum lightly with a hammer. Tap the hammer against the brake drum with an outward motion.
How do you replace parking brake on Kia?
Pull the primary brake shoe off of the backing plate then pull out the secondary brake shoe assembly. Remove the parking brake cable from the secondary shoe by removing the retaining clip with pliers then pulling the cable off. Use a large screwdriver to spread the control lever retaining clip then grasp the clip with pliers and pull it off.
Many Kia vehicles have drum brakes on the rear wheels. While drum brakes are generally less effective than disc brakes, they have the advantage of being lighter and less expensive. It is also easy to incorporate the parking brake into a drum brake, eliminating the need for a separate parking brake mechanism.
Use a screwdriver to attach the brake drum puller’s screw tightly. Tighten the screw until the brake drum puller is securely fastened around the brake drum. Do not over-tighten the screw on the brake drum puller. Knock the back of the brake drum lightly with a hammer. Tap the hammer against the brake drum with an outward motion.
Pull the primary brake shoe off of the backing plate then pull out the secondary brake shoe assembly. Remove the parking brake cable from the secondary shoe by removing the retaining clip with pliers then pulling the cable off. Use a large screwdriver to spread the control lever retaining clip then grasp the clip with pliers and pull it off.
What do you need to know about drum brakes?
Learn more… Drum brakes (as opposed to disc brakes) are a braking system that slows a vehicle by pressing brake shoes into the inside surface of a metal drum attached to the wheel to create friction. Like any braking system, drum brakes undergo wear and tear with use.
What should I do if my kick down Cable is bad?
Anytime you notice any of these warning signs, it’s important for you to contact a local ASE certified mechanic that has experience working on automatic transmissions. A faulty or worn out kickdown cable can be replaced rather easily. But, if the cable has broken, it may result in a complete transmission rebuild.
How does the kick down cable work in a car?
One component that helps both drive systems communicate is the kickdown cable. This device helps the engine relay information on revolutions per minute (RPM) to the automatic transmission and essentially tells it that it’s time to shift gears. Like any other component under the hood of your vehicle,…