What happens when a timing belt goes slack?
Basic Failure. Timing belt failure comes in three flavors: stretching, worn teeth and snapping, generally in that order. All timing belts stretch, and most of that stretch occurs about 15 minutes after installation. A spring-loaded tensioner keeps the belt tight, but after a while the tensioner will run out of travel and the belt will go slack.
What to do if your timing belt is off?
GO BACK THERE…THATS IT!!! TELL THEM A HONDA MECHANIC SAID THE TIMING IS OFF ONE OR MORE TEETH AND MUST BE CORRECTED. YOU WILL NOT PAYTHEM ONE RED CENT UNTIL NORMAL OPERATION IS RESTORED…THEY TOTALLY MESSED UP.
Why does my car vibrate after a timing belt change?
This is also a very precise allignment procedure while doing the T-belt service. This will make your cars engine vibrate in an unusual manner after a T-belt job. FAR more likely is that your cam timing is now off one tooth one direction or another. This is THE MOST LIKELY CAUSE OF THIS ISSUE IT IS NOT NORMAL AND WILL NOT GO AWAY…THEY SCREWED UP!!!
What happens to Honda Accord after timing belt change?
ALSO your honda 4cyliner in the Accord has a BALANCE SHAFT belt as well. This is also a very precise allignment procedure while doing the T-belt service. This will make your cars engine vibrate in an unusual manner after a T-belt job.
What happens when the timing belt is worn out?
A worn out timing belt might also impact the engine’s fire rate. The timing belt is attached to pulleys that drive the crank and camshaft as we’ve indicated above. However, sometimes the belt will slip on the camshaft drive and cause one cylinder to open or close earlier than it should.
When does a V-belt slip what happens?
What is belt slippage? Belt slippage occurs whenever torque demand exceeds the available friction between a V-belt and one or more of the pulleys (sheaves). When this occurs, the belt begins to slide backwards a bit as it moves with the pulley. This action is similar in two ways to slightly slipping the clutch in a manual transmission car:
Can a crank pulley be removed from a timing belt?
The crank pulley is the main pulley at the bottom of the engine. It needs to be removed in order to change the timing belt. However, it’s not easy if you only have hand tools, since the torque on this bolt is often pretty extreme.
What should I do if my timing belt snaps?
At this point, the camshaft sprockets will align with the marks on engine, and the crank sprocket will align with the marks on the engine. Some engines, like GM interference DOHC V6s, will require special tools keep the cams from moving, so consult with a factory service manual if you can.
Basic Failure. Timing belt failure comes in three flavors: stretching, worn teeth and snapping, generally in that order. All timing belts stretch, and most of that stretch occurs about 15 minutes after installation. A spring-loaded tensioner keeps the belt tight, but after a while the tensioner will run out of travel and the belt will go slack.
When do you lose power after timing belt change?
Right after the timing belt change I noticed that the car was more sluggish and did not accelerate as fast as before. Three days ago the car started losing power occasionally, especially when it was just starting and low speed. I could regain the power after about 30 second, and then it was fine.
What causes a car to start at the wrong time?
Spark plug wires are a source of electromagnetic interference (EMF), but this is usually only a problem on some aftermarket setups when this interference isn’t taken into account. A timing belt or chain that has skipped a tooth will throw off the cam timing, causing the intake and/or exhaust valves to open at the wrong time.
When to change timing belt on Honda Civic EX?
I have the timing belt changed on my 2001 Honda Civic EX two weeks ago. Right after the timing belt change I noticed that the car was more sluggish and did not accelerate as fast as before.
Can a worn out timing belt cause a fire?
Engine misfires A worn out timing belt might also impact the engine’s fire rate. The timing belt is attached to pulleys that drive the crank and camshaft as we’ve indicated above. However, sometimes the belt will slip on the camshaft drive and cause one cylinder to open or close earlier than it should.
What are the symptoms of a faulty timing belt?
Ticking noise coming from the engine. The timing belt is attached by way of a series of pulleys to the engine’s crank and cam shaft. The crankshaft powers the engine’s connecting rods which are attached to pistons inside the combustion chamber. The camshaft operates the cylinder head valves and rocker arm assembly, which…
What to do if your timing belt is broken?
Engine won’t turn over If the timing belt has broken inside, the engine will not be able to turn over or ignite. When you turn the key, you might hear the starter motor engage, but since the timing belt operates the crank and camshaft, it will not turn over. Obviously, if the car won’t start, a phone call to a mechanic is usually the first step.