How to replace the front drive shaft on a Kia Sorento?
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (B) with wire. 3. Remove the coking nut (A). The front hub coking nut should be replaced with new ones. After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4.
How to remove the coking nut on a Kia Sorento?
After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4. Remove the brake hose (A) and wheel speed sensor (B).
Can a pry bar be used on a Kia Sorento?
Use a pry bar being careful not to damage the transaxle and joint. Do not insert the pry bar too deep, as this may cause damage to the oil seal. Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.
Remove the brake caliper mounting bolts, and then place the brake caliper assembly (B) with wire. 3. Remove the coking nut (A). The front hub coking nut should be replaced with new ones. After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4.
How do you remove a CV axle from a Kia?
Wiggle the knuckle off, or place a pry bar between the strut and the knuckle until they are separated. Push or tap the CV axle shaft through the wheel hub until the two are separated. III. Removing the CV Axle From the Transmission Remove the splash guard that covers the crank shaft and harmonic balancer.
After installation coking nut (A), stake the coking nut using a chisel and hammer as shown in the illustration below. 4. Remove the brake hose (A) and wheel speed sensor (B).
Use a pry bar being careful not to damage the transaxle and joint. Do not insert the pry bar too deep, as this may cause damage to the oil seal. Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing.
How are driveshafts attached to center support bearings?
The two driveshaft’s that attach in the center support bearings are attached on opposite sides of the vehicle as well. The front drive shaft is attached to the output shaft coming out of the transmission, while the rear driveshaft’s propeller shaft is attached to the yoke that comes out of the rear axle differential.
Wiggle the knuckle off, or place a pry bar between the strut and the knuckle until they are separated. Push or tap the CV axle shaft through the wheel hub until the two are separated. III. Removing the CV Axle From the Transmission Remove the splash guard that covers the crank shaft and harmonic balancer.
Where are the CV joints on a driveshaft?
Driveshaft CV Joint Kit – Front, Propeller Shaft, Forward Position,… Propeller Shaft CV Joint Kit – 8 Bolt Hole, 35 Tooth, M8 X 2.15 Bolt… A Constant Velocity or CV joint is a drivetrain component that connects the driveshaft to the transmission, allowing power to be delivered to the wheels at a constant speed.
The two driveshaft’s that attach in the center support bearings are attached on opposite sides of the vehicle as well. The front drive shaft is attached to the output shaft coming out of the transmission, while the rear driveshaft’s propeller shaft is attached to the yoke that comes out of the rear axle differential.
How do you remove a front drive support bearing?
The front driveshaft is going to be attached solid inside the output shaft supports. In order to remove the driveshaft, you’ll need a rubber or plastic tipped hammer. On the front of the driveshaft is a welding mark that is solid and is the best place to hit with the hammer to loosen the driveshaft.
Where does the front drive shaft attach to the transmission?
Step 7: Locate where the front driveshaft attaches to the transmission. Using your chalk or marker, draw a solid line directly underneath the transmission output shaft and align that line to a similar line drawn on the front of the driveshaft.
Are there any problems with the Kia Sorento differential?
Kia Motor Sorento owners have reported 18 problems related to differential unit (under the power train category). The most recently reported issues are listed below. Also please check out the statistics and reliability analysis of Kia Motor Sorento based on all problems reported for the Sorento.
How many miles does a Kia Sorento have?
This 2014 Sorento only has 105,000 miles on it, mainly from highway driving. This was a major safety issue as I lost control of the vehicle. Had I been going faster, the likeliehood of an accident was high. While driving at 25 – 30 mph a loud noise sounded from under the car. A repetitive banging sound then occurred.
What should I do if I pull my Kia Sorento driveshaft?
Do not pull the driveshaft by excessive force it may cause components inside the joint kit to dislodge resulting in a torn boot or a damaged bearing. Plug the hole of the transaxle case with the oil seal cap to prevent contamination.
How many seats does a Kia Sorento have?
The well-proportioned 2014-2015 Sorento is sized between small and mid-sized SUVs, with plenty of interior space and easy maneuverability. It’s also simple to climb in or out and it offers an optional, though tiny third-row seat to bring seating to seven. There are 5 recalls on this vehicle.
When did I buy a 2004 Kia Sorento?
I foolishly purchased a 2004 Kia Sorento EX, in 2009, to date I have replaced the following, Crankshaft, rings, bearings, head qasket, radiator, oil pump. At a tune of 5300.00, at that time is how much I owed to pay it off.
When to replace transmission on used Kia Sorento?
Here are some tips for test driving a used Kia Sorento. Feel the transmission shift to make sure they are smooth. If you buy the car, don’t drive it too hard. My transmission needed to be replaced after 5 years around 100,000 miles.
What kind of car is a Kia Sorento?
Consumer Ratings Rank Vehicles HP #2 2004 Saturn VUE 250 #3 2004 Isuzu Axiom 250 #4 2004 Buick Rendezvous 245 #9 2003 Kia Sorento 192
Here are some tips for test driving a used Kia Sorento. Feel the transmission shift to make sure they are smooth. If you buy the car, don’t drive it too hard. My transmission needed to be replaced after 5 years around 100,000 miles.
What causes spongy brakes on a Kia Sorento?
Spongy brakes are common if the brake fluid has not been flush. Lack of power steering may also be a result of poor maintenance. Make sure that you have the fluids flushed out and replaced properly.
Why does my Kia Sorento get poor gas mileage?
The reason for the poor gas mileage is the ratio between horsepower and weight. If you don’t mind the gas mileage its a good buy. I foolishly purchased a 2004 Kia Sorento EX, in 2009, to date I have replaced the following, Crankshaft, rings, bearings, head qasket, radiator, oil pump.